Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY(for 2GR-FKS) › from 2016.11
RM3160E _52 Drivetrain _019686 DRIVE SHAFT / PROPELLER SHAFT _0295731 FRONT DRIVE SHAFT ASSEMBLY(for 2GR-FKS) A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY(for 2GR-FKS)  REASSEMBLY  


PROCEDURE

Hide 43410C 1.INSTALL FRONT DRIVE SHAFT BEARING (for AWD)

a.
C092032C05
1.063,0.292 1.323,0.292 1.323,0.292 1.323,0.604 false 0.844,1.177 1.156,1.177 1.156,1.177 1.156,1.313 false 2.344,1.396 2.156,1.396 2.156,1.396 2.156,1.552 false 0.885,0.208 1.219,0.469 0.333,0.26 10 false *a 0.552,1.094 1.01,1.354 0.458,0.26 10 false SST 2.396,1.302 2.792,1.583 0.396,0.281 10 false SST
*a Steel Plate


Using SST, a steel plate and a press, install a new front drive shaft bearing.

SST
09527-10011  

NOTICE:

The bearing should be completely installed.



b.
C092033

Using a snap ring expander, install a new drive shaft hole snap ring.

NOTICE:

Install the drive shaft hole snap ring securely.



Hide 2.INSTALL FRONT AXLE OUTBOARD JOINT BOOT

a.
C166359C04
1.917,0.885 2.427,0.375 2.427,0.375 2.792,0.375 false 2.823,0.281 3.177,0.49 0.354,0.208 10 *a
*a Protective Tape


Wrap the splines of the front drive outboard joint shaft assembly with protective tape to prevent the boot from being damaged.


b.
C274280C01
1.115,1.719 1.115,1.427 false 1.656,1.74 1.656,1.479 false 2.344,1.74 2.344,1.438 false 2.979,1.75 2.979,1.229 false 1.063,1.781 1.375,1.938 0.313,0.156 10 *1 1.604,1.792 1.917,1.948 0.313,0.156 10 *2 2.281,1.781 2.594,1.938 0.313,0.156 10 *3 2.948,1.792 3.26,1.948 0.313,0.156 10 *4
*1 Front Drive Outboard Joint Shaft Assembly
*2 Front No. 2 Axle Outboard Joint Boot Clamp
*3 Front Axle Outboard Joint Boot
*4 Front Axle Outboard Joint Boot Clamp
V100135

Outboard joint side
V100136

Inboard joint side


Install new parts to the front drive outboard joint shaft assembly in the following order:

i.

Front No. 2 axle outboard joint boot clamp


ii.

Front axle outboard joint boot


iii.

Front axle outboard joint boot clamp



c.

Pack the joint portion of the front drive outboard joint shaft assembly and front axle outboard joint boot with grease.

Standard Grease Capacity:

164 to 174 g (5.79 to 6.13 oz)



d.

Install the front axle outboard joint boot to the front drive outboard joint shaft assembly groove.

NOTICE:
·

Do not allow grease to adhere to the boot clamp track of the outboard joint boot.

·

Keep the inside of the outboard joint boot free of foreign matter.




Hide 3.INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP

a.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Install the front axle outboard joint boot clamp to the front axle outboard joint boot.


c.
C298538C01
2.219,1.26 2.74,1.26 true 2.792,1.177 3.25,1.375 0.458,0.198 10 false SST 2.448,1.719 2.76,1.917 0.313,0.198 10 false *a 1.542,0.125 1.854,0.323 0.313,0.198 10 false *b
*a Turn
*b Hold


Place SST to the front axle outboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


d.

Tighten SST so that the front axle outboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



e.

Remove SST.


f.
C164317N01
1.781,1.5 2.531,1.5 false 2.573,1.417 3.031,1.615 0.458,0.198 10 false SST

Using SST, measure the clearance of the front axle outboard joint boot clamp.

SST
09240-00020  

Clearance:

0.5 to 1.5 mm (0.0197 to 0.0590 in.)


If the clearance is outside the specified range, retighten SST.


Hide 4.INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP

a.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Install the front No. 2 axle outboard joint boot clamp to the front axle outboard joint boot.


c.
C285537C04
0.708,0.646 1.469,1.021 false 2.656,0.594 2.969,0.792 0.313,0.198 10 false *a 1.219,0.292 1.531,0.49 0.313,0.198 10 false *b 0.427,0.552 0.885,0.75 0.458,0.198 10 false SST
*a Turn
*b Hold


Place SST to the front No. 2 axle outboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


d.

Tighten SST so that the front No. 2 axle outboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



e.

Remove SST.


f.
C106165N13
2.031,1.031 2.698,1.844 false 2.646,1.865 3.094,2.104 0.448,0.24 10 SST

Using SST, measure the clearance of the front No. 2 axle outboard joint boot clamp.

SST
09240-00020  

Clearance:

0.5 to 1.5 mm (0.0197 to 0.0590 in.)


If the clearance is outside the specified range, retighten SST.


Hide 43474E 5.INSTALL FRONT DRIVE SHAFT DAMPER (w/ Drive Shaft Damper)

a.
C315781C04
0.167,1.604 0.167,1.365 false 1.198,1.615 1.198,1.375 false 0.646,1.615 0.646,1.448 false 1.719,0.385 2.177,0.583 0.458,0.198 10 false A 0.125,1.656 0.438,1.854 0.313,0.198 10 false *1 0.604,1.656 0.917,1.854 0.313,0.198 10 false *2 1.135,1.646 1.448,1.844 0.313,0.198 10 false *1
*1 Front Drive Shaft Damper Clamp
*2 Front Drive Shaft Damper


Temporarily install the front drive shaft damper and 2 new front drive shaft damper clamps to the front drive outboard joint shaft assembly as shown in the illustration.


b.

Set the dimension (A) as specified below.

Dimension (A):
for LH Side 234.9 to 238.9 mm (9.25 to 9.40 in.)
for RH Side 229.9 to 233.9 mm (9.06 to 9.20 in.)



c.

Install the 2 front drive shaft damper clamps to the front drive shaft damper.

NOTICE:

Make sure to install the clamps in the correct position.



d.
C292475

Using needle-nose pliers, install the 2 front drive shaft damper clamps.


Hide 6.INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY

a.
C274277C02
0.688,1.875 0.688,1.333 false 1.698,1.854 1.698,1.615 false 2.49,1.875 2.49,1.667 false 2.927,1.885 2.927,1.25 false 0.625,1.896 0.938,2.052 0.313,0.156 10 *1 1.635,1.896 1.948,2.052 0.313,0.156 10 *2 2.417,1.906 2.729,2.063 0.313,0.156 10 *3 2.875,1.896 3.188,2.052 0.313,0.156 10 *a
*1 Front Axle Inboard Joint Boot Clamp
*2 Front Axle Inboard Joint Boot
*3 Front No. 2 Axle Inboard Joint Boot Clamp
*a Protective Tape
V100135

Outboard joint side
V100136

Inboard joint side


Install new parts to the front drive outboard joint shaft assembly in the following order:

i.

Front axle inboard joint boot clamp


ii.

Front axle inboard joint boot


iii.

Front No. 2 axle inboard joint boot clamp



b.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



c.

Remove the protective tape.


d.
C067417C02
1.26,1.719 2.125,1.719 2.125,1.719 1.76,1.427 false 2.156,1.625 2.542,1.885 0.385,0.26 10 false *a
*a Matchmark


Align the matchmarks and install the tripod joint to the front drive outboard joint shaft assembly.

NOTICE:

Face the serrated side of the tripod joint outward and install it to the outboard joint end.



e.

Align the matchmarks placed before removal.


f.

Using a brass bar and a hammer, install the tripod joint to the front drive outboard joint shaft assembly.

NOTICE:
·

Do not tap the rollers.

·

Keep the tripod joint free of foreign matter.

·

Be sure to install the tripod joint in the correct direction.




g.
F045046

Using a snap ring expander, install a new shaft snap ring to the front drive outboard joint shaft assembly.


h.

Pack the front drive inboard joint assembly and front axle inboard joint boot with grease.

Standard Grease Capacity:

195 to 205 g (6.88 to 7.23 oz)



i.
C345676C02
1.198,1.656 0.573,1.656 0.573,1.656 0.573,0.781 true 1.042,1.646 1.042,0.781 true 1.229,1.573 1.542,1.771 0.313,0.198 10 false *a
*a Lip


Install a new front axle inboard joint grommet to the front drive inboard joint assembly.

NOTICE:
·

Securely fit the protrusion on the front axle inboard joint grommet into the front drive inboard joint assembly.

·

Make sure that the lip of the front axle inboard joint grommet is not damaged.




j.
C345674C03
1.448,1.031 0.969,0.5 0.969,0.5 1.906,0.646 true 0.792,0.417 1.104,0.615 0.313,0.198 10 false *a
*a Matchmark


Align the matchmarks and install the front drive inboard joint assembly to the front drive outboard joint shaft assembly.


Hide 7.INSTALL FRONT AXLE INBOARD JOINT BOOT

a.

Install the front axle inboard joint boot to the front drive inboard joint assembly.


b.
C157783N28
1.563,1.688 1.792,1.865 0.229,0.177 10 false A

Check whether the drive shaft dimension (A) is within specification.

Dimension (A) (for 2WD):
for LH Side 604.75 mm (1.98 ft.)
for RH Side 925.55 mm (3.04 ft.)


Dimension (A) (for AWD):
for LH Side 604.75 mm (1.98 ft.)
for RH Side 926.55 mm (3.04 ft.)



Hide 8.INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP

a.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Install the front axle inboard joint boot clamp to the front axle inboard joint boot.


c.
C296175C02
1.74,1.396 2.104,1.708 2.104,1.708 2.729,1.708 true 2.781,1.625 3.24,1.823 0.458,0.198 10 false SST 2.729,0.094 3.042,0.292 0.313,0.198 10 false *a 1.448,0.521 1.76,0.719 0.313,0.198 10 false *b
*a Turn
*b Hold


Place SST to the front axle inboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


d.

Tighten SST so that the front axle inboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



e.

Remove SST.


f.
C195760N02
1.531,1.5 2.365,1.5 false 2.406,1.417 2.854,1.667 0.448,0.25 10 false SST

Using SST, measure the clearance of the front axle inboard joint boot clamp.

SST
09240-00020  

Clearance:

0.5 to 1.5 mm (0.0197 to 0.0590 in.)


If the clearance is outside the specified range, retighten SST.


Hide 9.INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP

a.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Install the front No. 2 axle inboard joint boot clamp to the front axle inboard joint boot.


c.
C298539C02
0.677,1.625 1.521,1.625 1.521,1.625 2.146,1.125 true 0.385,1.542 0.844,1.74 0.458,0.198 10 false SST 2.281,1.76 2.594,1.958 0.313,0.198 10 false *a 1.938,0.073 2.25,0.271 0.313,0.198 10 false *b
*a Turn
*b Hold


Place SST to the front No. 2 axle inboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


d.

Tighten SST so that the front No. 2 axle inboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



e.

Remove SST.


f.
C086270N05
0.708,1.333 1.125,1.333 1.125,1.333 1.656,0.885 true 0.406,1.25 0.865,1.448 0.458,0.198 10 false SST

Using SST, measure the clearance of the front No. 2 axle inboard joint boot clamp.

SST
09240-00020  

Clearance:

0.5 to 1.5 mm (0.0197 to 0.0590 in.)


If the clearance is outside the specified range, retighten SST.