Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › from 2016.11
RM3160E _51 Engine / Hybrid System _019684 CRUISE CONTROL _0109815 CRUISE CONTROL SYSTEM J

CRUISE CONTROL  CRUISE CONTROL SYSTEM  Cruise Control Switch Circuit  


DESCRIPTION

The cruise control main switch is used to turn the cruise control system on and off, as well as operate 7 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP and CANCEL. The SET, TAP-DOWN and - (COAST) functions, and the RES (RESUME), TAP-UP and + (ACCEL) functions are operated with the same switch. The cruise control main switch is an automatic return type switch which turns on only while operating it in the direction of each arrow and turns off after releasing it. The internal contact points of the cruise control main switch turn on with switch operation. Then the ECM reads the voltage value that has been changed by the switch operation to control the SET, - (COAST), RES (RESUME), + (ACCEL), and CANCEL functions.

WIRING DIAGRAM

for 1AR-FE
A369504E72
6.542,2.781 6.99,3 0.448,0.219 10 false ECM 4.583,2.552 5.646,2.906 1.063,0.354 10 false Spiral Cable Sub-assembly 3.469,2.573 4.385,2.948 0.917,0.375 10 false Cruise Control Switch Wire 0.792,2.594 2.521,2.813 1.729,0.219 10 false Cruise Control Main Switch 0.448,1.438 1.365,1.635 0.917,0.198 10 false CANCEL 1.219,1.427 1.833,1.625 0.615,0.198 10 false -SET 1.875,1.427 2.49,1.625 0.615,0.198 10 false +RES 2.51,1.427 3.427,1.625 0.917,0.198 10 false ON-OFF 2.771,0.771 3.229,0.969 0.458,0.198 10 false CCS 4.906,0.792 5.365,0.99 0.458,0.198 10 false CCS 6.385,0.875 6.844,1.073 0.458,0.198 10 false CCS 4.906,1.99 5.365,2.188 0.458,0.198 10 false ECC 2.75,1.979 3.208,2.177 0.458,0.198 10 false ECC 4.417,0.875 4.729,1.073 0.313,0.198 10 false z8 3.26,0.875 3.573,1.073 0.313,0.198 10 false A 5.521,0.875 5.958,1.083 0.438,0.208 10 false F61 6.375,2.594 6.833,2.792 0.458,0.198 10 false A43 6.156,0.75 6.906,0.969 0.75,0.219 10 false 40 5.594,1.865 5.75,2.063 0.156,0.198 10 false 2 5.604,0.667 5.76,0.865 0.156,0.198 10 false 1 4.406,0.667 4.646,0.865 0.24,0.198 10 false 3 3.26,0.656 3.417,0.854 0.156,0.198 10 false 3 4.427,1.854 4.583,2.052 0.156,0.198 10 false 4 3.26,1.865 3.417,2.063 0.156,0.198 10 false 1 3.75,0.781 4.208,0.979 0.458,0.198 10 false CCS 3.75,1.99 4.208,2.188 0.458,0.198 10 false ECC 3.26,2.073 3.573,2.271 0.313,0.198 10 false A 5.521,2.073 5.958,2.281 0.438,0.208 10 false F61 4.417,2.083 4.729,2.281 0.313,0.198 10 false z8

for 2GR-FKS
A369504E73
6.542,2.781 6.99,3 0.448,0.219 10 false ECM 4.615,2.552 5.729,2.927 1.115,0.375 10 false Spiral Cable Sub-assembly 3.469,2.573 4.385,2.948 0.917,0.375 10 false Cruise Control Switch Wire 0.792,2.594 2.521,2.813 1.729,0.219 10 false Cruise Control Main Switch 0.448,1.438 1.365,1.635 0.917,0.198 10 false CANCEL 1.219,1.427 1.833,1.625 0.615,0.198 10 false -SET 1.875,1.427 2.49,1.625 0.615,0.198 10 false +RES 2.51,1.427 3.427,1.625 0.917,0.198 10 false ON-OFF 2.771,0.771 3.229,0.969 0.458,0.198 10 false CCS 4.906,0.792 5.365,0.99 0.458,0.198 10 false CCS 6.385,0.875 6.844,1.073 0.458,0.198 10 false CCS 4.906,1.99 5.365,2.188 0.458,0.198 10 false ECC 2.75,1.979 3.208,2.177 0.458,0.198 10 false ECC 4.417,0.875 4.729,1.073 0.313,0.198 10 false z8 3.26,0.875 3.573,1.073 0.313,0.198 10 false A 5.521,0.875 5.958,1.083 0.438,0.208 10 false F61 6.375,2.594 6.833,2.792 0.458,0.198 10 false A43 6.167,0.781 6.479,0.979 0.313,0.198 10 false 41 5.594,1.865 5.75,2.063 0.156,0.198 10 false 2 5.604,0.667 5.76,0.865 0.156,0.198 10 false 1 4.406,0.667 4.646,0.865 0.24,0.198 10 false 3 3.26,0.656 3.417,0.854 0.156,0.198 10 false 3 4.427,1.854 4.583,2.052 0.156,0.198 10 false 4 3.26,1.865 3.417,2.063 0.156,0.198 10 false 1 3.75,0.781 4.208,0.979 0.458,0.198 10 false CCS 3.75,1.99 4.208,2.188 0.458,0.198 10 false ECC 3.26,2.073 3.573,2.271 0.313,0.198 10 false A 5.521,2.073 5.958,2.281 0.438,0.208 10 false F61 4.417,2.083 4.729,2.281 0.313,0.198 10 false z8

PROCEDURE

1.READ VALUE ON GTS
a.
E107091C01
2.144,0.084 2.42,0.273 0.276,0.189 10 *c 2.763,1.172 3.003,1.374 0.24,0.202 10 *a 1.934,1.577 2.325,1.779 0.391,0.202 10 *b 1.033,1.235 1.268,1.437 0.235,0.202 10 *d
*a ON-OFF
*b -SET
*c +RES
*d CANCEL


Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Cruise Control*1 or Radar Cruise 1*2 / Data List.


e.

Check the Data List to confirm proper functioning of the cruise control main switch.

Powertrain > Cruise Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Main SW M-CPU Cruise control main switch signal (Main CPU) ON or OFF ON: Cruise control main switch (ON-OFF button) being pushed and held
OFF: Cruise control main switch (ON-OFF button) released
-
Cancel Switch Switch CANCEL switch signal ON or OFF ON: CANCEL switch operated
OFF: CANCEL switch released
-
SET/COAST Switch -SET switch signal ON or OFF ON: -SET switch operated
OFF: -SET switch released
-
RES/ACC Switch +RES switch signal ON or OFF ON: +RES switch operated
OFF: +RES switch released
-
Powertrain > Cruise Control > Data List
Tester Display
Main SW M-CPU
Cancel Switch
SET/COAST Switch
RES/ACC Switch
50003 237 16,23,22,21
Powertrain > Radar Cruise1 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Cancel Switch CANCEL switch status ON or OFF ON: CANCEL switch on
OFF: CANCEL switch off
-
-SET Switch -SET switch status ON or OFF ON: -SET switch on
OFF: -SET switch off
-
+RES Switch +RES switch status ON or OFF ON: +RES switch on
OFF: +RES switch off
-
Cruise Main Switch Operation Condition Cruise control main switch (ON-OFF button) status ON or OFF ON: Cruise control main switch (ON-OFF button) pushed
OFF: Cruise control main switch (ON-OFF button) not pushed
-
Powertrain > Radar Cruise1 > Data List
Tester Display
Cancel Switch
-SET Switch
+RES Switch
Cruise Main Switch Operation Condition
50003 374 18,19,20,41
OK:

When the cruise control main switch is operated, the display changes as shown above.



*1: for 1AR-FE

*2: for 2GR-FKS


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT CRUISE CONTROL MAIN SWITCH
2.INSPECT CRUISE CONTROL MAIN SWITCH
a.

Inspect the cruise control main switch.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL MAIN SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK CRUISE CONTROL SWITCH WIRE

NG

3.CHECK CRUISE CONTROL SWITCH WIRE
a.
A315700C13
1.302,0.385 1.708,0.667 0.406,0.281 1.271,2.885 1.677,3.167 0.406,0.281 0.781,4.344 1.198,3.927 true 0.948,2.271 1.365,1.854 true 2.042,2.26 1.635,1.854 true 2.052,4.323 1.646,3.917 true 0.396,0.688 0.708,0.906 0.313,0.219 10 false *a 0.5,3.104 0.813,3.302 0.313,0.198 10 false *b 1.427,0.448 1.74,0.646 0.313,0.198 10 false z8 1.427,2.948 1.74,3.146 0.313,0.198 10 false A 0.813,2.281 1.271,2.479 0.458,0.198 10 false CCS 1.938,4.354 2.396,4.552 0.458,0.198 10 false CCS 0.604,4.354 1.063,4.552 0.458,0.198 10 false ECC 1.896,2.281 2.354,2.479 0.458,0.198 10 false ECC
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)
*b Front view of wire harness connector
(to Cruise Control Main Switch)


Remove the cruise control switch wire.

Click hereSteering>STEERING COLUMN>STEERING WHEEL>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z8-3 (CCS) - A-3 (CCS) Always Below 1 Ω
z8-4 (ECC) - A-1 (ECC) Always Below 1 Ω
z8-3 (CCS) or A-3 (CCS) - Body ground Always 10 kΩ or higher
z8-4 (ECC) or A-1 (ECC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE CRUISE CONTROL SWITCH WIRE

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)

NG

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)
a.

Disconnect the F61 spiral cable sub-assembly.


b.

Disconnect the A43 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for 1AR-FE):
Tester Connection Condition Specified Condition
F61-1 (CCS) - A43-40 (CCS) Always Below 1 Ω
F61-2 (ECC) - Body ground Always Below 1 Ω
F61-1 (CCS) or A43-40 (CCS) - Body ground Always 10 kΩ or higher


Standard Resistance (for 2GR-FKS):
Tester Connection Condition Specified Condition
F61-1 (CCS) - A43-41 (CCS) Always Below 1 Ω
F61-2 (ECC) - Body ground Always Below 1 Ω
F61-1 (CCS) or A43-41 (CCS) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK A
NG B



A

B

REPAIR OR REPLACE HARNESS OR CONNECTOR