Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 1AR-FE) › from 2016.11
RM3160E _51 Engine / Hybrid System _019684 CRUISE CONTROL _0296315 DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 1AR-FE) C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 1AR-FE)  U0235  Lost Communication with Cruise Control Front Distance Range Sensor  U1104  Lost Communication with Driving Support ECU  


DESCRIPTION

The driving support ECU assembly sends vehicle speed and vehicle condition information to the millimeter wave radar sensor assembly. The millimeter wave radar sensor assembly then sends information on the presence, distance, and relative speed of objects in front of the vehicle to the driving support ECU assembly. The driving support ECU assembly sends this information to the ECM and the ECM operates the dynamic radar cruise control system.

DTC No. Detection Item DTC Detection Condition Trouble Area
U0235 Lost Communication with Cruise Control Front Distance Range Sensor
·

While the vehicle speed is 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, a communication error between the millimeter wave radar sensor assembly and the driving support ECU assembly is detected for approximately 1 second.


·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly

·

Harness or connector


U1104 Lost Communication with Driving Support ECU
·

While the vehicle speed is 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, a communication error between the driving support ECU assembly and the millimeter wave radar sensor assembly is detected for approximately 1 second.


·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly

·

Harness or connector



WIRING DIAGRAM

A395895E01
1.052,5.26 4.719,5.458 3.667,0.198 10 false : CAN Communication Line 4.094,5.396 6.115,5.615 2.021,0.219 10 false Driving Support ECU Assembly 3.708,5.396 5.729,5.615 2.021,0.219 10 false F128 4.135,4.875 4.906,5.094 0.771,0.219 10 false GND 4.135,4.208 4.906,4.427 0.771,0.219 10 false B 4.5,4.188 5.271,4.406 0.771,0.219 10 false CA1P 4.51,2.99 5.281,3.208 0.771,0.219 10 false CA1P 4.469,1.302 5.24,1.521 0.771,0.219 10 false CANH 4.51,4.865 5.281,5.083 0.771,0.219 10 false CA1N 4.51,2.406 5.281,2.625 0.771,0.219 10 false CA1N 4.5,0.75 5.271,0.969 0.771,0.219 10 false CANL 2.958,3.573 5.573,3.781 2.615,0.208 10 false Millimeter Wave Radar Sensor Assembly 2.969,3.417 4.99,3.635 2.021,0.219 10 false A81 4.135,3.125 4.906,3.344 0.771,0.219 10 false SGND 4.146,1.396 4.917,1.615 0.771,0.219 10 false GND 4.146,0.635 4.917,0.854 0.771,0.219 10 false IGB 4.146,2.458 4.917,2.677 0.771,0.219 10 false IGB 3.979,4.094 4.75,4.313 0.771,0.219 10 false 7 3.896,4.729 4.667,4.948 0.771,0.219 10 false 28 4.938,3.958 5.708,4.177 0.771,0.219 10 false 8 4.948,4.667 5.719,4.885 0.771,0.219 10 false 9 4.948,2.219 5.719,2.438 0.771,0.219 10 false 6 4.938,2.823 5.708,3.042 0.771,0.219 10 false 5 1.958,4.406 2.729,4.625 0.771,0.219 10 false IG1 NO. 3 3.302,1.802 5.323,2.021 2.021,0.219 10 false S18 3.958,0.51 4.729,0.729 0.771,0.219 10 false 7 3.896,1.271 4.667,1.49 0.771,0.219 10 false 10 4.917,0.563 5.688,0.781 0.771,0.219 10 false 12 4.948,1.115 5.719,1.333 0.771,0.219 10 false 6 3.969,2.344 4.74,2.563 0.771,0.219 10 false 8 3.958,3.021 4.729,3.24 0.771,0.219 10 false 1 3.615,1.802 6.229,2.01 2.615,0.208 10 false Forward Recognition Camera 0.021,4.198 1.396,4.438 1.375,0.24 10 false from IG1 NO. 3 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the driving support ECU assembly, make sure to replace it with a new one. If a device which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle, and as a result, a DTC may be stored.

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Using the GTS, check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN communication system DTCs are not output OK
CAN communication system DTCs are output NG



OK

2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BATTERY AND BODY GROUND)

NG

2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.

Disconnect the F128 driving support ECU assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F128-7 (B) - Body ground Engine switch on (IG) 11 to 14 V
F128-7 (B) - Body ground Engine switch off Below 1 V


Standard Resistance:
Tester Connection Condition Specified Condition
F128-28 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BATTERY AND BODY GROUND)
a.
A393386C03
1.5,0.177 1.896,0.417 0.396,0.24 0.875,1.583 1.417,1.063 true 2.458,1.625 1.948,1.208 true 0.094,0.115 0.406,0.271 0.313,0.156 10 false *a 0.469,1.552 1.083,1.75 0.615,0.198 10 false SGND 2.521,1.552 3.135,1.75 0.615,0.198 10 false IGB 1.583,0.219 2.198,0.417 0.615,0.198 10 false A81
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the A81 millimeter wave radar sensor assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A81-8 (IGB) - Body ground Engine switch on (IG) 11 to 14 V
A81-8 (IGB) - Body ground Engine switch off Below 1 V


Standard Resistance:
Tester Connection Condition Specified Condition
A81-1 (SGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.

Disconnect the F128 driving support ECU assembly connector.


b.

Disconnect the A81 millimeter wave radar sensor assembly connector.


c.

Disconnect the S18 forward recognition camera connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F128-8 (CA1P) - A81-5 (CA1P) Always Below 1 Ω
F128-9 (CA1N) - A81-6 (CA1N) Always Below 1 Ω
F128-8 (CA1P) or A81-5 (CA1P) - Body ground Always 10 kΩ or higher
F128-9 (CA1N) or A81-6 (CA1N) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly with a new one.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


b.

Perform millimeter wave radar sensor assembly adjustment.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR DTCs (RADAR CRUISE 2)
6.CHECK FOR DTCs (RADAR CRUISE 2)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 1AR-FE)>DTC CHECK / CLEAR

Powertrain > Radar Cruise2 > Clear DTCs
50002 197

b.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the following conditions are not met, the system cannot detect the malfunction.

1.

Turn the engine switch on (IG).

2.

Turn the dynamic radar cruise control system on using the cruise control main switch (ON-OFF button).

3.

Drive the vehicle at 36 km/h (22 mph) or more for 1 second or more.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 1AR-FE)>DTC CHECK / CLEAR

Powertrain > Radar Cruise2 > Trouble Codes
50001 197

Result:
Result Proceed to
DTC U0235 and U1104 are not output A
DTC U0235 or U1104 is output B



A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B