CHECK FOR INSTALLED SYSTEMS (ECUS AND SENSORS) THAT USE CAN COMMUNICATION
The systems (ECUs and sensors) that use CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed to the vehicle.
| Connected to | Code | ECU/Sensor Name | GTS Display | Applicability |
|---|---|---|---|---|
| - | CGW | Central Gateway ECU (Network Gateway ECU) | ·
CAN Gateway1 ·
CAN Gateway2 |
Installed on all vehicles |
| V Bus | DLC3 | DLC3 | - | Installed on all vehicles |
| Bus 2 | MET | Combination Meter Assembly | Combination Meter | Installed on all vehicles |
| BRK | Skid Control ECU (Brake Actuator Assembly) | Skid Control (ABS/VSC/TRAC) | Installed on all vehicles | |
| SRS | Airbag Sensor Assembly | Airbag | Installed on all vehicles | |
| CS | Clearance Warning ECU Assembly | Clearance Warning (Clearance Sonar) | Vehicles with Toyota Parking Assist-sensor System | |
| SMT | Certification ECU (Smart Key ECU Assembly) | Certification (Smart) | Vehicles with Smart Entry and Start System | |
| A/C | Air Conditioning Amplifier Assembly | Air Conditioning Amplifier | Installed on all vehicles | |
| LIT | Headlight Leveling ECU Assembly | Headlight swivel (AFS) | Vehicles with Automatic Headlight Beam Level Control System | |
| STR | Steering Sensor | Spiral cable (Steering Angle Sensor) | Installed on all vehicles | |
| ENG | ECM | ECM (Engine) | Installed on all vehicles | |
| AWD | 4WD ECU Assembly | Four Wheel Drive Control | Vehicles with AWD | |
| EPS | Power Steering ECU Assembly | Power Steering (EPS) | Installed on all vehicles | |
| MB | Main Body ECU (Multiplex Network Body ECU) | Main Body | Installed on all vehicles | |
| Bus 3 | AV | Navigation Receiver Assembly | Display and Navigation (AVN) | Vehicles with Navigation Receiver Type |
| Radio and Display Receiver Assembly | Display and Navigation (AVN) | Vehicles with Radio and Display Type | ||
| DCM | Telematics Transceiver | DCM | Vehicles with Telematics Transceiver | |
| Bus 5 | F-CAM | Forward Recognition Camera | Front Camera Module | Vehicles with Toyota Safety Sense |
| F-MR | Millimeter Wave Radar Sensor Assembly | Front Radar | Vehicles with Toyota Safety Sense | |
| DS | Driving Support ECU Assembly | Driving Support (Cruise Control-ACC) | Vehicles with Toyota Safety Sense | |
| PAC | Parking Assist ECU | Panoramic View Monitor | Vehicles with Panoramic View Monitor System | |
| BSM | Blind Spot Monitor Sensor LH | Blind Spot Monitor Master | Vehicles with Blind Spot Monitor System | |
| R-CA | Television Camera Assembly | Parking Assist Monitor System | Vehicles with Parking Assist Monitor System | |
| Sub Bus 1 | MB | Main Body ECU (Multiplex Network Body ECU) | - | Installed on all vehicles |
| MIR-R | Outer Mirror Control ECU Assembly (for Front Passenger Side) | ·
Front Door RH/R-Mirror (FR-Door2/R-Mirror) (for LHD) ·
Front Door LH/L-Mirror (FL-Door2/L-Mirror) (for RHD) |
Vehicles with Seat Position Memory System | |
| DST | Position Control ECU and Switch Assembly | D-Seat | Vehicles with Seat Position Memory System | |
| MIR-L | Outer Mirror Control ECU Assembly (for Driver Side) | ·
Front Door LH/L-Mirror (FL-Door2/L-Mirror) (for LHD) ·
Front Door RH/R-Mirror (FR-Door2/R-Mirror) (for RHD) |
Vehicles with Seat Position Memory System | |
| BKD | Multiplex Network Door ECU | Back Door | Vehicles with Power Back Door System |
The names of ECUs and sensors shown on the GTS display may differ from those shown in the DTC Table by ECU section that follows.
CAN BUS CHECK
The ECUs and sensors that are properly connected to the CAN communication system can be displayed using the GTS.
Using the GTS, select the CAN Bus Check screen.
It may be possible to select buses that do not have ECUs or sensors from the bus selection pull-down menu. This is not a malfunction. (This occurs when optional devices are not on a sub bus that is monitored by a gateway function equipped ECU.)
In the bus selection pull down menu, all buses applicable to the model are displayed (e.g. LIN communication buses are also displayed). Therefore, refer to the wiring diagrams to check the names of sub buses for CAN communication.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>SYSTEM DIAGRAM
Different connection statuses are indicated by the background color of ECUs and sensors that are displayed.
| Bus Type | Background Color | Connection Status |
|---|---|---|
| Bus | White | Communication has been normal. |
| Yellow | Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication). | |
| Red | Currently not communicating (either of the following):
·
Not communicating since the start of the CAN bus check ·
Communication occurred at least once since the start of the CAN bus check, but is currently not occurring. |
|
| Not displayed | Either of the following:
·
The central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS.*4 ·
No ECUs or sensors are connected to the bus.*5 |
|
| Sub bus with a gateway function equipped ECU that does not memorize connected ECUs or sensors*2 | White | Communication has been normal since the start of the CAN bus check. |
| Yellow | Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication). | |
| Red | Communication occurred at least once since the start of the CAN bus check, but is currently not occurring. | |
| Not displayed | Communication stop has continued since the start of the CAN bus check.*1 | |
| Sub bus with a gateway function equipped ECU that memorizes connected ECUs and sensors*3 | White | Communication has been normal. |
| Yellow | Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication). | |
| Red | Currently not communicating (either of the following):
·
Not communicating since the start of the CAN bus check ·
Communication occurred at least once since the start of the CAN bus check, but is currently not occurring. |
|
| Not displayed | Either of the following:
·
The gateway function equipped ECU cannot communicate with the central gateway ECU (network gateway ECU).*6 ·
No ECUs or sensors are connected to the sub bus.*7 |
Gateway function equipped ECUs relay signals between ECUs and sensors connected to different buses.
*1: An ECU or sensor is installed to the vehicle but is not displayed on the "Communication Bus Check" screen.
*2: The gateway function equipped ECU does not memorize ECUs and sensors connected to its respective sub bus.
*3: The gateway function equipped ECU memorizes ECUs and sensors connected to its respective sub bus.
*4: When the central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS, the name of buses, sub buses, ECUs and sensors will not be displayed.
*5: When no ECUs or sensors are connected to a bus, the message "There is no system found on the communication Bus." will be displayed.
*6: When a gateway function equipped ECU cannot communicate with the central gateway ECU (network gateway ECU), the name of sub buses and ECUs or sensors connected to the sub bus will not be displayed.
*7: When no ECUs or sensors are connected to the sub bus, the message "There is no system found on the communication Bus." will be displayed.
If there is no communication between the GTS and the vehicle, or no ECUs or sensors are displayed as connected, check the central gateway ECU (network gateway ECU) and V bus (the bus that connects the DLC3 to the central gateway ECU (network gateway ECU)) for malfunctions.
Observe the connection response screen for approximately 2 minutes to check for a change in connection status of the connected ECUs and sensors.
If an open occurs in one of the lines of a CAN branch (except DLC3), output from the other branch line (the line that is not open) will be unstable and it may interfere with the response (display) of other ECUs and sensors.
If the connection status changes during the inspection, repair the open in the branch line of the ECU or sensor that does not respond (is not detected) and then perform the CAN bus check again.
HOW TO INTERPRET CAN BUS CHECK SCREEN
When a communication stop is currently occurring, the probable malfunctioning part can be determined from the CAN bus check and by using the following methods.
The following CAN bus wiring diagram is provided only as an example. This wiring diagram is different from the actual wiring diagram for this vehicle.
When a communication stop is currently occurring, it is easier to determine the probable malfunctioning part from the CAN bus check rather than from communication DTCs.
Wait for approximately 2 minutes after turning the ignition switch to ON (or simulate the driving conditions that enable the malfunction to be reproduced) and select "CAN Bus Check". Then observe the communication status of each ECU on the screen.
If a communication error of only 1 ECU or sensor is indicated on the CAN Bus Check screen, a communication stop of the ECU or sensor is suspected.
Open in both CAN branch lines of HV on the bus 4
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub Bus | *d | V Bus |
| *e | Location of Malfunction | *f | Background color is red |
When there are communication stops, ECUs that are present in the vehicle may not be displayed on the CAN Bus Check screen.
If communication errors for multiple ECUs or sensors are indicated on the CAN Bus Check screen, then a communication stop of the ECU or sensor that shows a more serious communication stop (an ECU or sensor whose background color is red) is suspected.
Example: Open in a CAN branch line for HV on the bus 4
| *a | Background color is red | *b | Background color intermittently becomes yellow or red |
| *c | Not displayed or background color is yellow or red | - | - |
| Bus Type | Background Color | Connection Status |
|---|---|---|
| Bus | White | Communication has been normal. |
| Yellow | Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication). | |
| Red | Currently not communicating (either of the following):
·
Not communicating since the start of the CAN bus check ·
Communication occurred at least once since the start of the CAN bus check, but is currently not occurring. |
|
| Not displayed | Either of the following:
·
The central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS.*4 ·
No ECUs or sensors are connected to the bus.*5 |
|
| Sub bus with a gateway function equipped ECU that does not memorize connected ECUs or sensors*2 | White | Communication has been normal since the start of the CAN bus check. |
| Yellow | Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication). | |
| Red | Communication occurred at least once since the start of the CAN bus check, but is currently not occurring. | |
| Not displayed | Communication stop has continued since the start of the CAN bus check.*1 | |
| Sub bus with a gateway function equipped ECU that memorizes connected ECUs and sensors*3 | White | Communication has been normal. |
| Yellow | Communication stop occurred at least once since the start of the CAN bus check, but communication is currently occurring (unstable communication). | |
| Red | Currently not communicating (either of the following):
·
Not communicating since the start of the CAN bus check ·
Communication occurred at least once since the start of the CAN bus check, but is currently not occurring. |
|
| Not displayed | Either of the following:
·
The gateway function equipped ECU cannot communicate with the central gateway ECU (network gateway ECU).*6 ·
No ECUs or sensors are connected to the sub bus.*7 |
Gateway function equipped ECUs relay signals between ECUs and sensors connected to different buses.
*1: An ECU or sensor is installed to the vehicle but is not displayed on the "Communication Bus Check" screen.
*2: The gateway function equipped ECU does not memorize ECUs and sensors connected to its respective sub bus.
*3: The gateway function equipped ECU memorizes ECUs and sensors connected to its respective sub bus.
*4: When the central gateway ECU (network gateway ECU) has an internal malfunction or cannot communicate with the GTS, the name of buses, sub buses, ECUs and sensors will not be displayed.
*5: When no ECUs or sensors are connected to a bus, the message "There is no system found on the communication Bus." will be displayed.
*6: When a gateway function equipped ECU cannot communicate with the central gateway ECU (network gateway ECU), the name of sub buses and ECUs or sensors connected to the sub bus will not be displayed.
*7: When no ECUs or sensors are connected to the sub bus, the message "There is no system found on the communication Bus." will be displayed.
The example of the CAN Bus Check screen in the illustration shows the result of electrical noise on the CAN bus which is caused by an open in a CAN branch line of HV is also unstable. In addition, in this example, MB is equipped with a gateway function. Therefore, communication is also unstable between the Sub bus ECUs of MB and the bus 4.
The example in the illustration shows that HV has a red background color on the CAN Bus Check screen. This indicates a more significant communication stop. In this case, a communication stop of HV is suspected.
If a communication error is indicated on both the bus 4 and Sub bus on the CAN Bus Check screen, suspect any communication stop displayed for the bus 4 first.
Example: Open in both CAN branch lines of MB on the bus 4
| *a | Background color is red | *b | Not displayed |
In the CAN bus check, it is possible to confirm the communication status of ECUs connected to the bus after connecting the GTS to the DLC3. As for sub bus, it is possible to confirm which sub bus connected ECUs can communicate with a gateway function equipped ECU on the bus.
If a gateway function equipped ECU has a communication error, ECUs connected to the gateway function equipped ECU are also affected, and communication stops will be indicated.
The CAN Bus Check screen in the illustration shows that MB has a gateway function and a communication stop in MB is suspected.
If the CAN Bus Check screen indicates a communication stop only in the sub bus, a communication stop in the sub bus is suspected.
Example: Open in both CAN branch lines of MIR-R on the sub bus
| *a | Background color is red | - | - |
A communication error in a sub bus does not affect the other buses.
When a gateway function equipped ECU has memorized the ECUs that are connected to the sub bus, if any of the ECUs connected to the gateway function equipped ECU has a communication error, the background color changes to yellow or red. (The displayed name will not disappear.)
If both of the bus 2 main bus lines are open, ECUs or sensors that are located farther away from the central gateway ECU (network gateway ECU) than the open part will be displayed as a communication stop on the CAN Bus Check screen.
(In this case, HVB, R-MGC and ENG background color changes to red.)
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub Bus | *d | V Bus |
| *e | Location of Malfunction | *f | Background color is red |
If a communication error occurs in an ECU, it is not displayed on the CAN Bus Check screen even though the ECU is present.
If both of the sub bus main bus lines are open, ECUs that are located farther away from the gateway function equipped ECU than the open part will be displayed as a communication stop on the CAN Bus Check screen.
(In this case, MIR-L background color changes to red.)
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub Bus | *d | V Bus |
| *e | Location of Malfunction | *f | Background color is red |
When any of the following malfunctions occur, CAN communication cannot be established and almost all ECUs and sensors on the bus show a communication error on the CAN Bus Check screen.
| Short between CAN lines (CANH and CANL) |
| Short between a CAN line (CANH or CANL) and +B |
| Short between a CAN line (CANH or CANL) and ground |
| Open in a CAN main bus line |
| *a | When any of the following malfunctions occur on the bus 4 | *b | When any of the following malfunctions occur on a sub bus |
| *c | Background color is red | *d | Not displayed |
When a malfunction occurs in the bus, almost all ECUs and sensors on the bus and sub bus indicate a communication error (almost all ECUs are not displayed). As communication with the gateway function equipped ECU that is connected to the bus stops, communication from the ECUs connected to the sub bus that is monitored by the gateway function equipped ECU also stops (these ECUs are not displayed).
When a malfunction occurs in a sub bus, almost all ECUs connected to the sub bus indicate a communication error.
A communication error in a sub bus does not affect the other buses.
The malfunctioning part can be determined by checking for a short circuit between CAN bus lines or between a CAN bus line and ground or +B short using an electrical tester.
If a communication error of all ECUs and sensors is indicated on the CAN Bus Check screen, a communication stop of the V bus (DLC3 - central gateway ECU (network gateway ECU)) is suspected.
Open in both CAN branch lines in the V bus
| *a | Bus 2 | *b | Bus 4 |
| *c | Sub Bus | *d | V Bus |
| *e | Location of Malfunction | *f | Not displayed |
When there is no communication between the GTS and the vehicle, no ECUs or sensors will be displayed.
DTC TABLE BY ECU
In the CAN communication system, the CAN communication DTCs of each ECU can be displayed using the GTS.
If CAN communication system DTCs are output, the malfunction cannot be determined only by the DTCs. Perform troubleshooting according to How to Proceed with Troubleshooting.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
If the system function temporarily returns to normal, DTCs may not be output again even though the following DTC check procedures are used.
ECM (for 1AR-FE) / GTS Display "Engine and ECT"
This ECU uses the CAN communication system for DTC communication.
*1: Refer to Automatic Transaxle System.
Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>U0100
*2: Refer to SFI System.
Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>U0101
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100*1 | Lost Communication with ECM/PCM "A" | The TCM does not receive data from the ECM for 1.25 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the ECM is 10.5 V or more. |
Turn the ignition switch to ON and wait at least 1.25 seconds. | MIL illuminates. | DTC is stored until it is cleared using the GTS. |
| U0101*2 | Lost Communication with TCM | The ECM does not receive data from the TCM for 1.25 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the ECM is 10.5 V or more. |
Turn the ignition switch to ON and wait at least 1.25 seconds. | MIL illuminates. | DTC is stored until it is cleared using the GTS. |
ECM (for 2GR-FKS) / GTS Display "Engine"
This ECU uses the CAN communication system for DTC communication.
*: Refer to SFI System.
Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>U010187
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U010187* | Lost Communication with TCM Missing Message | The ECM does not receive data from the TCM for 1.25 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the ECM is 10 V or more. |
Turn the ignition switch to ON and wait at least 3.5 seconds. | MIL illuminates. | DTC is stored until it is cleared using the GTS. |
TCM (for 2GR-FKS) / GTS Display "Transmission"
This ECU uses the CAN communication system for DTC communication.
*: Refer to Automatic Transaxle System.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U010087* | Lost Communication with ECM/PCM "A" Missing Message | The TCM does not receive data from the ECM for 1.25 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the ECM is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 2.5 seconds. | MIL illuminates. | DTC is stored until it is cleared using the GTS. |
Skid Control ECU (Brake Actuator Assembly) / GTS Display "ABS/VSC/TRC"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0073 | Control Module Communication Bus Off | One of the following conditions is met:
·
Delayed reception of data from the steering sensor and airbag sensor assembly continues for 1 second or more. ·
The following condition occurs 10 times or more within 60 seconds: -
Delayed reception of data from the steering sensor and airbag sensor assembly occurs once or more within 5 seconds. ·
The following condition occurs 10 times in succession: -
The skid control ECU (brake actuator assembly) cannot send/receive data (bus off) once or more within 0.1 seconds. |
Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the skid control ECU (brake actuator assembly) (+BS terminal voltage) is between 10 and 17.4 V. |
Turn the ignition switch to ON and wait at least 60 seconds. | ·
ABS warning light illuminates. ·
Slip indicator light illuminates. ·
Brake warning light illuminates. |
DTC is stored until it is cleared using the GTS. |
| U0100 | Lost Communication With ECM/PCM | The skid control ECU (brake actuator assembly) does not receive data from the ECM for 2 seconds or more. | All conditions are met:
·
The ignition switch is ON for 1 second or more. ·
Vehicle speed is 15 km/h (9 mph) or more. ·
The power source voltage of the skid control ECU (brake actuator assembly) (+BS terminal voltage) is between 10 and 17.4 V. |
Turn the ignition switch to ON and drive the vehicle at a speed of 15 km/h (9 mph) or more for 3 seconds or more. | Slip indicator light illuminates. | DTC is stored until it is cleared using the GTS. |
| U0124 | Lost Communication With Lateral Acceleration Sensor Module | Either of the following conditions is met:
·
The skid control ECU (brake actuator assembly) does not receive data from the airbag sensor assembly for 1 second or more. ·
The following condition occurs 10 times or more within 60 seconds: -
The skid control ECU (brake actuator assembly) does not receive data from the airbag sensor assembly once or more within 5 seconds. |
Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the skid control ECU (brake actuator assembly) (+BS terminal voltage) is between 10 and 17.4 V. |
Turn the ignition switch to ON and wait at least 60 seconds. | ·
ABS warning light illuminates. ·
Slip indicator light illuminates. |
DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication With Steering Angle Sensor Module | Either of the following conditions is met:
·
The skid control ECU (brake actuator assembly) does not receive data from the steering sensor for 1 second or more. ·
The following condition occurs 10 times or more within 60 seconds: -
The skid control ECU (brake actuator assembly) does not receive data from the steering sensor once or more within 5 seconds. |
Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the skid control ECU (brake actuator assembly) (+BS terminal voltage) is between 10 and 17.4 V. |
Turn the ignition switch to ON and wait at least 60 seconds. | Slip indicator light illuminates. | DTC is stored until it is cleared using the GTS. |
Power Steering ECU Assembly / GTS Display "EMPS"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM/PCM "A" | The power steering ECU assembly does not receive data from the ECM for 5 seconds or more. | All conditions are met:
·
The ignition switch is ON for 1 second or more. ·
Vehicle speed is 20 km/h (12 mph) or more. ·
The power source voltage of the power steering ECU assembly is 9 V or more. |
Drive the vehicle at a speed of 20 km/h (12 mph) or more for 6 seconds or more. | EPS warning light illuminates. | DTC remains stored only while malfunction is occurring. |
| U0129 | Lost Communication with Brake System Control Module | The power steering ECU assembly cannot receive data from the skid control ECU (brake actuator assembly) for 2.34 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 2 seconds or more. ·
The power source voltage of the power steering ECU assembly is 9 V or more. |
Turn the ignition switch to ON and wait at least 4.34 seconds. | EPS warning light illuminates. | DTC remains stored only while malfunction is occurring. |
Main Body ECU (Multiplex Network Body ECU) / GTS Display "Main Body"
This ECU uses the CAN communication system for DTC communication.
*1: for LHD
*2: for RHD
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication With ECM/PCM "A" | The main body ECU (multiplex network body ECU) does not receive data from the ECM for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0101 | Lost Communication with TCM | The main body ECU (multiplex network body ECU) does not receive data from the TCM for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0120 | Lost Communication With Starter / Generator Control Module | The main body ECU (multiplex network body ECU) does not receive data from the certification ECU (smart key ECU assembly) for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The main body ECU (multiplex network body ECU) does not receive data from the skid control ECU (brake actuator assembly) for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0151 | Lost Communication with Restraints Control Module | The main body ECU (multiplex network body ECU) does not receive data from the airbag sensor assembly for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Instrument Panel Cluster (IPC) Control Module | The main body ECU (multiplex network body ECU) does not receive data from the combination meter assembly for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0164 | Lost Communication with HVAC Control Module | The main body ECU (multiplex network body ECU) does not receive data from the air conditioning amplifier assembly for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0199 | Lost Communication with ''Door Control Module A'' | ·
The main body ECU (multiplex network body ECU) does not receive data from the outer mirror control ECU assembly (for front passenger side) for 10 seconds or more. *1 ·
The main body ECU (multiplex network body ECU) does not receive data from the outer mirror control ECU assembly (for driver side) for 10 seconds or more.*2 |
Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0200 | Lost Communication with ''Door Control Module B'' | ·
The main body ECU (multiplex network body ECU) does not receive data from the outer mirror control ECU assembly (for driver side) for 10 seconds or more.*1 ·
The main body ECU (multiplex network body ECU) does not receive data from the outer mirror control ECU assembly (for front passenger side) for 10 seconds or more. *2 |
Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0208 | Lost Communication with ''Seat Control Module A'' | The main body ECU (multiplex network body ECU) does not receive data from the position control ECU and switch assembly for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0230 | Lost Communication with Rear Gate Module | The main body ECU (multiplex network body ECU) does not receive data from the multiplex network door ECU for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U023A | Lost Communication With Image Processing Module "A" | The main body ECU (multiplex network body ECU) does not receive data from the forward recognition camera for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0327 | Software Incompatibility with Vehicle Security Control Module | The main body ECU (multiplex network body ECU) does not receive data from the certification ECU (smart key ECU assembly) for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U1002 | Lost Communication with Gateway Module | The main body ECU (multiplex network body ECU) detects communication errors between itself and the position control ECU and switch assembly, outer mirror control ECU assembly (for front passenger side), outer mirror control ECU assembly (for driver side) and multiplex network door ECU. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U1126 | Lost Communication with Parking Assist Monitor Module | The main body ECU (multiplex network body ECU) does not receive data from the television camera assembly for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the main body ECU (multiplex network body ECU) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
Certification ECU (Smart Key ECU Assembly) / GTS Display "Entry&Start"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication With ECM/PCM | The certification ECU (smart key ECU assembly) does not receive data from the ECM for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Body Control Module "B" | The certification ECU (smart key ECU assembly) does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Instrument Panel Cluster (IPC) Control Module | The certification ECU (smart key ECU assembly) does not receive data from the combination meter assembly for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected and 10 seconds or more elapse. ·
The power source voltage of the certification ECU (smart key ECU assembly) is 10 V or more. |
Turn the ignition switch to ON and wait at least 20 seconds. | - | DTC is stored until it is cleared using the GTS. |
Certification ECU (Smart Key ECU Assembly) / GTS Display "Power Source Control"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | ECM Communication | The certification ECU (smart key ECU assembly) does not receive data from the ECM for 3.1 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the certification ECU (smart key ECU assembly) is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 4.1 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0140 | Lost Communication with Body Control Module | The certification ECU (smart key ECU assembly) does not receive data from the main body ECU (multiplex network body ECU) for 3 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the certification ECU (smart key ECU assembly) is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 3 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Instrument Panel Cluster (IPC) Control Module | The certification ECU (smart key ECU assembly) does not receive data from the combination meter assembly for 3.1 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the certification ECU (smart key ECU assembly) is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 3.1 seconds. | - | DTC is stored until it is cleared using the GTS. |
Certification ECU (Smart Key ECU Assembly) / GTS Display "Starting Control"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM/PCM "A" | The certification ECU (smart key ECU assembly) does not receive data from the ECM for 2 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the certification ECU (smart key ECU assembly) is 10.5 V or more. |
Turn the ignition switch to ON and wait at least 2 seconds. | - | DTC remains stored only while malfunction is occurring. |
Headlight Leveling ECU Assembly / GTS Display "HL AutoLeveling"
This ECU uses the CAN communication system for DTC communication.
*: The headlight leveling ECU assembly stores this DTC if an internal error related to the CAN communication system is detected.
Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM>U1000
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM/PCM "A" | The headlight leveling ECU assembly does not receive data from the ECM for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the headlight leveling ECU assembly is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 13 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The headlight leveling ECU assembly does not receive data from the skid control ECU (brake actuator assembly) for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the headlight leveling ECU assembly is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 13 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Body Control Module "B" | The headlight leveling ECU assembly does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the headlight leveling ECU assembly is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 13 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U1000* | CAN Communication Failure(Message Registry) | When the ignition switch is turned ON, a CAN communication malfunction is detected. | The ignition switch is ON. | Turn the ignition switch to ON. | Displays messages on the multi-information display. | DTC remains stored only while malfunction is occurring. |
Television Camera Assembly / GTS Display "IPA/Parking Assist Monitor"
This ECU uses the CAN communication system for DTC communication.
*: The television camera assembly stores this DTC if an internal error related to the CAN communication system is detected.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>U1000
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM/PCM "A" | The television camera assembly does not receive data from the ECM for 11 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the television camera assembly is 5.5 V or more. |
Turn the ignition switch to ON and wait at least 14 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication with Steering Angle Sensor Module | The television camera assembly does not receive data from the steering sensor for 11 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the television camera assembly is 5.5 V or more. |
Turn the ignition switch to ON and wait at least 14 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The television camera assembly does not receive data from the skid control ECU (brake actuator assembly) for 11 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the television camera assembly is 5.5 V or more. |
Turn the ignition switch to ON and wait at least 14 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0131 | Lost Communication with Power Steering Control Module | The television camera assembly does not receive data from the power steering ECU assembly for 11 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the television camera assembly is 5.5 V or more. |
Turn the ignition switch to ON and wait at least 14 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0140 | Lost Communication with Body Control Module | The television camera assembly does not receive data from the main body ECU (multiplex network body ECU) for 11 seconds or more. | Both conditions are met:
·
The ignition switch is ACC for 3 seconds or more. ·
The power source voltage of the television camera assembly is 5.5 V or more. |
Turn the ignition switch to ON and wait at least 14 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0163 | Lost Communication with Navigation Control Module | The television camera assembly does not receive data from the radio and display receiver assembly for 11 seconds or more. | Both conditions are met:
·
The ignition switch is ACC for 3 seconds or more. ·
The power source voltage of the television camera assembly is 5.5 V or more. |
Turn the ignition switch to ON and wait at least 14 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0233 | Lost Communication with Blind Spot Monitor Master Module | The television camera assembly does not receive data from the blind spot monitor sensor LH for 11 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the television camera assembly is 5.5 V or more. |
Turn the ignition switch to ON and wait at least 14 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U1000* | CAN Communication Failure(Message Registry) | When the ignition switch is turned ON, a CAN communication malfunction is detected. | The ignition switch is ON. | Turn the ignition switch to ON. | - | DTC remains stored only while malfunction is occurring. |
| U1110 | Lost Communication with Clearance Sonar Module | The television camera assembly does not receive data from the clearance warning ECU assembly for 11 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the television camera assembly is 5.5 V or more. |
Turn the ignition switch to ON and wait at least 14 seconds. | - | DTC is stored until it is cleared using the GTS. |
Air Conditioning Amplifier Assembly / GTS Display "Air Conditioner"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication With ECM/PCM "A" | The air conditioning amplifier assembly does not receive data from the ECM for 5 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the air conditioning amplifier assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 5 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0131 | Lost Communication With Power Steering Control Module | The air conditioning amplifier assembly does not receive data from the power steering ECU assembly for 5 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the air conditioning amplifier assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 5 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication With Body Control Module "B" | The air conditioning amplifier assembly does not receive data from the main body ECU (multiplex network body ECU) for 5 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the air conditioning amplifier assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 5 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication With Instrument Panel Cluster (IPC) Control Module | The air conditioning amplifier assembly does not receive data from the combination meter assembly for 5 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the air conditioning amplifier assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 5 seconds. | - | DTC is stored until it is cleared using the GTS. |
Navigation Receiver Assembly / GTS Display "Navigation System"
This ECU uses the CAN communication system for DTC communication.
*1: w/ Toyota Parking Assist-sensor System
*2: w/o Toyota Parking Assist-sensor System
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0073 | Sending Malfunction (Navigation to APGS) | The navigation receiver assembly does not send/receive data for 5 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the navigation receiver assembly is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 6 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0100 | Engine ECU Communication | Either of the following conditions is met:
·
The navigation receiver assembly does not receive data from the ECM for 12 seconds or more.*1 ·
The navigation receiver assembly does not receive data from the ECM for 4 seconds or more.*2 |
Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the navigation receiver assembly is 9.5 V or more. |
·
Turn the ignition switch to ON and wait at least 13 seconds.*1 ·
Turn the ignition switch to ON and wait at least 5 seconds.*2 |
- | DTC is stored until it is cleared using the GTS. |
| U0140 | Lost Communication with Body Control Module | The navigation receiver assembly does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the navigation receiver assembly is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 11 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Meter ECU Communication | The navigation receiver assembly does not receive data from the combination meter assembly for 30 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the navigation receiver assembly is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 31 seconds. | - | DTC is stored until it is cleared using the GTS. |
Radio and Display Receiver Assembly / GTS Display "Navigation System"
This ECU uses the CAN communication system for DTC communication.
*1: w/ Toyota Parking Assist-sensor System
*2: w/o Toyota Parking Assist-sensor System
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0073 | Sending Malfunction (Navigation to APGS) | The radio and display receiver assembly does not send/receive data for 5 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 6 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0100 | Engine ECU Communication | Either of the following conditions is met:
·
The radio and display receiver assembly does not receive data from the ECM for 12 seconds or more.*1 ·
The radio and display receiver assembly does not receive data from the ECM for 4 seconds or more.*2 |
Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
·
Turn the ignition switch to ON and wait at least 13 seconds.*1 ·
Turn the ignition switch to ON and wait at least 5 seconds.*2 |
- | DTC is stored until it is cleared using the GTS. |
| U0140 | Lost Communication with Body Control Module | The radio and display receiver assembly does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 11 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Meter ECU Communication | The radio and display receiver assembly does not receive data from the combination meter assembly for 30 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the radio and display receiver assembly is 9.5 V or more. |
Turn the ignition switch to ON and wait at least 31 seconds. | - | DTC is stored until it is cleared using the GTS. |
Combination Meter Assembly / GTS Display "Combination Meter"
This ECU uses the CAN communication system for DTC communication.
*1: for Navigation Receiver Type
*2: for Radio and Display Type
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM/PCM "A" | The combination meter assembly does not receive data from the ECM for 3 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the combination meter assembly is 11.5 V or more. |
Turn the ignition switch to ON and wait at least 4 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The combination meter assembly does not receive data from the skid control ECU (brake actuator assembly) for 3 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the combination meter assembly is 11.5 V or more. |
Turn the ignition switch to ON and wait at least 4 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0131 | Lost Communication with Power Steering Control Module | The combination meter assembly does not receive data from the power steering ECU assembly for 3 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the combination meter assembly is 11.5 V or more. |
Turn the ignition switch to ON and wait at least 4 seconds. | EPS warning light illuminates. | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Body Control Module "B" | The combination meter assembly does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the combination meter assembly is 11.5 V or more. |
Turn the ignition switch to ON and wait at least 11 seconds. | Tire pressure warning light illuminates. | DTC is stored until it is cleared using the GTS. |
| U0151 | Lost Communication with Restraints Control Module | The combination meter assembly does not receive data from the airbag sensor assembly for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the combination meter assembly is 11.5 V or more. |
Turn the ignition switch to ON and wait at least 11 seconds. | ·
SRS warning light illuminates. ·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
| U0163 | Lost Communication With Navigation Control Module | ·
The combination meter assembly does not receive data from the navigation receiver assembly for 3 seconds or more.*1 ·
The combination meter assembly does not receive data from the radio and display receiver assembly for 3 seconds or more.*2 |
Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the combination meter assembly is 11.5 V or more. |
Turn the ignition switch to ON and wait at least 4 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0182 | Lost Communication with Lighting Control Module Front | The combination meter assembly does not receive data from the headlight leveling ECU assembly for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the combination meter assembly is 11.5 V or more. |
Turn the ignition switch to ON and wait at least 11 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U023A | Lost Communication with Front Camera Module | The combination meter assembly does not receive data from the forward recognition camera for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the combination meter assembly is 11.5 V or more. |
Turn the ignition switch to ON and wait at least 11 seconds. | ·
Lane departure alert indicator light illuminates. ·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
| U1104 | Lost Communication with Driving Support ECU | The combination meter assembly does not receive data from the driving support ECU assembly for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the combination meter assembly is 11.5 V or more. |
Turn the ignition switch to ON and wait at least 11 seconds. | ·
PCS warning light flashes. ·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
Outer Mirror Control ECU Assembly (for Front Passenger Side) / GTS Display "Mirror R" (for LHD), "Mirror L" (for RHD)
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0142 | Lost Communication With Body Control Module ''B'' | The outer mirror control ECU assembly (for front passenger side) does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected. ·
The power source voltage of the outer mirror control ECU assembly (for front passenger side) is 10 V or more. |
Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
Outer Mirror Control ECU Assembly (for Driver Side) / GTS Display "Mirror L" (for LHD), "Mirror R" (for RHD)
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0142 | Lost Communication With Body Control Module ''B'' | The outer mirror control ECU assembly (for driver side) does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. | Both conditions are met:
·
Power source status change (+B OFF → ON, ACC ON ←→ OFF, IG ON ←→ OFF) is detected. ·
The power source voltage of the outer mirror control ECU assembly (for driver side) is 10 V or more. |
Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
Multiplex Network Door ECU / GTS Display "Back Door"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0101 | Lost Communication with TCM | The multiplex network door ECU does not receive data from the ECM for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the multiplex network door ECU is 10.5 V or more. |
Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0122 | Lost Communication with Vehicle Dynamics Control Module | The multiplex network door ECU does not receive data from the skid control ECU (brake actuator assembly) for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the multiplex network door ECU is 10.5 V or more. |
Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Body Control Module "B" | The multiplex network door ECU does not receive data from the main body ECU (multiplex network body ECU) for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the multiplex network door ECU is 10.5 V or more. |
Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Instrument Panel Cluster (IPC) Control Module | The multiplex network door ECU does not receive data from the combination meter assembly for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The power source voltage of the multiplex network door ECU is 10.5 V or more. |
Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
ECM (for 2GR-FKS) / GTS Display "Radar Cruise1"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U012287 | Lost Communication with Vehicle Dynamics Control Module Missing Message | The ECM does not receive data from the skid control ECU (brake actuator assembly) for 2.65 seconds or more. | All conditions are met:
·
The ignition switch is ON for 1 second or more. ·
Cruise control main switch is on. ·
The power source voltage of the ECM is 10.5 V or more. |
Allow the cruise control system to operate for 2.65 seconds or more. | - | DTC is stored until it is cleared using the GTS. |
ECM (for 1AR-FE) / GTS Display "Radar Cruise1"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM/PCM "A" | The skid control ECU (brake actuator assembly) does not receive data from the ECM for 1 second or more. | Both conditions are met:
·
The ignition switch is ON. ·
The radar cruise control system (vehicle control mode) is operating. |
Allow the radar cruise control system (vehicle control mode) to operate for 1 second or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0122 | Lost Communication with Vehicle Dynamics Control Module | The ECM does not receive data from the skid control ECU (brake actuator assembly) for 2.65 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The radar cruise control system (vehicle control mode) is operating. |
Allow the radar cruise control system (vehicle control mode) to operate for 2.65 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U1104 | Lost Communication with Distance Control Module | The driving support ECU assembly data sent to the ECM, skid control ECU (brake actuator assembly) or millimeter wave radar sensor assembly is lost for 1.02 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The radar cruise control system (vehicle control mode) is operating. |
Allow the radar cruise control system (vehicle control mode) to operate for 1.02 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
ECM (for 2GR-FKS) / GTS Display "Radar Cruise1"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U010087 | Lost Communication with ECM/PCM "A" Missing Message | The skid control ECU (brake actuator assembly) does not receive data from the ECM for 1 second or more. | Both conditions are met:
·
The ignition switch is ON. ·
The radar cruise control system (vehicle control mode) is operating. |
Allow the radar cruise control system (vehicle control mode) to operate for 1 second or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U012287 | Lost Communication with Vehicle Dynamics Control Module Missing Message | The ECM does not receive data from the skid control ECU (brake actuator assembly) for 2.65 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The radar cruise control system (vehicle control mode) is operating. |
Allow the radar cruise control system (vehicle control mode) to operate for 2.65 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U110487 | Lost Communication with Driving Support ECU Missing Message | The driving support ECU assembly data sent to the ECM, skid control ECU (brake actuator assembly) or millimeter wave radar sensor assembly is lost for 1.02 seconds or more. | Both conditions are met:
·
The ignition switch is ON. ·
The radar cruise control system (vehicle control mode) is operating. |
Allow the radar cruise control system (vehicle control mode) to operate for 1.02 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
Driving Support ECU Assembly / GTS Display "Radar Cruise2"
This ECU uses the CAN communication system for DTC communication.
*: Refer to Dynamic Radar Cruise Control System.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM/PCM "A" | The driving support ECU assembly does not receive data from the ECM for 0.92 seconds or more. | All conditions are met:
·
The ignition switch is ON for 1 second or more. ·
Vehicle speed is 36 km/h (22 mph) or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. ·
The cruise control main switch is on. |
Turn the cruise control main switch on and drive the vehicle at a speed of 36 km/h (22 mph) or more for 1.92 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0125 | Lost Communication with Yaw Rate Sensor Module | The driving support ECU assembly does not receive data from the airbag sensor assembly for 0.72 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
Vehicle speed is 36 km/h (22 mph) or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. ·
The cruise control main switch is on. |
Turn the cruise control main switch on and drive the vehicle at a speed of 36 km/h (22 mph) or more for 3.72 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication with Steering Angle Sensor Module | The driving support ECU assembly does not receive data from the steering sensor for 0.72 seconds or more. | All conditions are met:
·
The ignition switch is ON for 1 second or more. ·
Vehicle speed is 36 km/h (22 mph) or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. ·
The cruise control main switch is on. |
Turn the cruise control main switch on and drive the vehicle at a speed of 36 km/h (22 mph) or more for 1.72 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The driving support ECU assembly does not receive data from the skid control ECU (brake actuator assembly) for 1.08 seconds or more. | All conditions are met:
·
The ignition switch is ON for 2 seconds or more. ·
Vehicle speed is 36 km/h (22 mph) or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. ·
The cruise control main switch is on. |
Turn the cruise control main switch on and drive the vehicle at a speed of 36 km/h (22 mph) or more for 3.08 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0235* | Lost Communication with Cruise Control Front Distance Range Sensor | The driving support ECU assembly does not receive data from the millimeter wave radar sensor assembly for 1.6 seconds or more. | All conditions are met:
·
The ignition switch is ON for 1 second or more. ·
Vehicle speed is 36 km/h (22 mph) or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. ·
The cruise control main switch is on. |
Turn the cruise control main switch on and drive the vehicle at a speed of 36 km/h (22 mph) or more for 2.6 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U1104* | Lost Communication with Driving Support ECU | The driving support ECU assembly does not receive data from the millimeter wave radar sensor assembly for 0.144 seconds or more. | All conditions are met:
·
The ignition switch is ON for 1 second or more. ·
Vehicle speed is 36 km/h (22 mph) or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. ·
The cruise control main switch is on. |
Turn the cruise control main switch on and drive the vehicle at a speed of 36 km/h (22 mph) or more for 1.144 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
Driving Support ECU Assembly / GTS Display "Pre-Collision 2"
This ECU uses the CAN communication system for DTC communication.
*: Refer to Pre-Collision System.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM/PCM "A" | The driving support ECU assembly does not receive data from the ECM for 5.12 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
Vehicle speed is 5 km/h (3 mph) or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
Drive the vehicle at a speed of 5 km/h (3 mph) or more for 8.12 seconds or more. | ·
Displays messages on the multi-information display. ·
PCS indicator light blinks. |
DTC is stored until it is cleared using the GTS. |
| U0125 | Lost Communication with Yaw Rate Sensor Module | The driving support ECU assembly does not receive data from the airbag sensor assembly for 0.72 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
Turn the ignition switch to ON and wait for at least 3.72 seconds. | ·
Displays messages on the multi-information display. ·
PCS indicator light blinks. |
DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication with Steering Angle Sensor Module | The driving support ECU assembly does not receive data from the steering sensor for 5.04 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
Turn the ignition switch to ON and wait for at least 6.04 seconds. | ·
Displays messages on the multi-information display. ·
PCS indicator light blinks. |
DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The driving support ECU assembly does not receive data from the skid control ECU (brake actuator assembly) for 4.92 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
Turn the ignition switch to ON and wait for at least 6.92 seconds. | ·
Displays messages on the multi-information display. ·
PCS indicator light blinks. |
DTC is stored until it is cleared using the GTS. |
| U0235* | Lost Communication with Cruise Control Front Distance Range Sensor | The driving support ECU assembly does not receive data from the millimeter wave radar sensor assembly for 0.3 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
Turn the ignition switch to ON and wait for at least 3.3 seconds. | ·
Displays messages on the multi-information display. ·
PCS indicator light blinks. |
DTC is stored until it is cleared using the GTS. |
| U023A* | Lost Communication with Image Processing Module "A" | The driving support ECU assembly does not receive data from the forward recognition camera for 3 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
Turn the ignition switch to ON and wait for at least 6 seconds. | ·
Displays messages on the multi-information display. ·
PCS indicator light blinks. |
DTC is stored until it is cleared using the GTS. |
| U1002* | Lost Communication with Gateway Module | The driving support ECU assembly does not receive data from the millimeter wave radar sensor assembly and forward recognition camera for 0.5 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
Turn the ignition switch to ON and wait for at least 3.5 seconds. | ·
Displays messages on the multi-information display. ·
PCS indicator light blinks. |
DTC is stored until it is cleared using the GTS. |
| U1104* | Lost Communication with Driving Support ECU | Either of the following conditions is met:
·
The millimeter wave radar sensor assembly or forward recognition camera does not receive data from the driving support ECU assembly for 0.224 seconds or more. ·
The skid control ECU (brake actuator assembly) does not receive data from the driving support ECU assembly for 1.456 seconds or more. |
Both conditions are met:
·
The ignition switch is ON for 2 seconds or more. ·
The power source voltage of the driving support ECU assembly is 10 V or more. |
Turn the ignition switch to ON and wait for at least 3.456 seconds. | ·
Displays messages on the multi-information display. ·
PCS indicator light blinks. |
DTC is stored until it is cleared using the GTS. |
Clearance Warning ECU Assembly / GTS Display "Clearance Sonar"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0101 | Lost Communication with TCM | The clearance warning ECU assembly does not receive data from the ECM for 5 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 5 seconds or more. ·
The power source voltage of the clearance warning ECU assembly is 10.2 V or more. |
Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication With Instrument Panel Cluster (IPC) Control Module | The clearance warning ECU assembly does not receive data from the combination meter assembly for 5 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 5 seconds or more. ·
The power source voltage of the clearance warning ECU assembly is 10.2 V or more. |
Turn the ignition switch to ON and wait at least 10 seconds. | - | DTC is stored until it is cleared using the GTS. |
4WD ECU Assembly / GTS Display "Four Wheel Drive"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0073 | Control Module Communication Bus Off | The 4WD ECU assembly keeps sending data to an ECU or a sensor for 5 seconds or more because a receive completion signal is not received. | Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the 4WD ECU assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 6 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0100 | Lost Communication With ECM/PCM "A" | The 4WD ECU assembly does not receive data from the ECM for 3.5 seconds or more. | All conditions are met:
·
The ignition switch is ON for 1 second or more. ·
Vehicle speed is 60 km/h (37 mph) or more. ·
The power source voltage of the 4WD ECU assembly is 10 V or more. |
Drive the vehicle at a speed of 60 km/h (37 mph) or more for 4.5 seconds or more. | - | DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication With Steering Angle Sensor Module | Either of the following conditions is met:
·
The 4WD ECU assembly does not receive data from the steering sensor for 1 second or more. ·
condition occurs 10 times or more within 60 seconds: -
The 4WD ECU assembly does not receive data from the steering sensor once or more within 5 seconds. |
Both conditions are met:
·
The ignition switch is ON for 1 second or more. ·
The power source voltage of the 4WD ECU assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 60 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication With Brake System Control Module | The 4WD ECU assembly does not receive data from the skid control ECU (brake actuator assembly) for 8 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 2 seconds or more. ·
The power source voltage of the 4WD ECU assembly is 10 V or more. |
Turn the ignition switch to ON and wait at least 10 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
Blind Spot Monitor Sensor LH / GTS Display "Blind Spot Monitor Master"
This ECU uses the CAN communication system for DTC communication.
*: If U0232 or U1331 is output alone, the CAN communication is normal.
(Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>U0232 for U0232, Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>U1331 for U1331)
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM/PCM "A" | The blind spot monitor sensor LH does not receive data from the ECM for 10.84 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the blind spot monitor sensor LH is 10 V or more. |
Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch) and wait at least 13.84 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0125 | Lost Communication with Yaw Rate Sensor Module | The blind spot monitor sensor LH does not receive data from the airbag sensor assembly for 3.06 seconds or more. | All conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
Vehicle speed is 7 km/h (4 mph) or more. ·
The power source voltage of the blind spot monitor sensor LH is 10 V or more. |
Turn the blind spot monitor main switch on and then drive the vehicle at a speed of 7 km/h (or 4 mph) or more for 6.06 seconds or more. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication with Steering Angle Sensor Module | The blind spot monitor sensor LH does not receive data from the steering sensor for 10.68 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the blind spot monitor sensor LH is 10 V or more. |
Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch) and wait at least 13.68 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The blind spot monitor sensor LH does not receive data from the skid control ECU (brake actuator assembly) for 3.036 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the blind spot monitor sensor LH is 10 V or more. |
Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch) and wait at least 6.036 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Body Control Module "B" | The blind spot monitor sensor LH does not receive data from the main body ECU (multiplex network body ECU) for 10.6 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the blind spot monitor sensor LH is 10 V or more. |
Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch) and wait at least 13.6 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U0232* | Lost Communication with Blind Spot Monitor Slave Module | The blind spot monitor sensor LH does not receive data from the blind spot monitor sensor RH for 10.6 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the blind spot monitor sensor LH is 10 V or more. |
Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch) and wait at least 13.6 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
| U1331* | Software Incompatibility with Body Control Module "B" | Destination information of the main body ECU (multiplex network body ECU) and blind spot monitor sensor do not match. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the blind spot monitor sensor LH is 10 V or more. |
Turn the ignition switch to ON, turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch) and wait at least 3 seconds. | Displays messages on the multi-information display. | DTC is stored until it is cleared using the GTS. |
Forward Recognition Camera / GTS Display "LKA/LDA"
This ECU uses the CAN communication system for DTC communication.
*: Refer to Lane Departure Alert System.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM/PCM "A" | The forward recognition camera does not receive data from the ECM for 5 seconds or more. | All conditions are met:
·
The power source voltage (IGB terminal voltage) of the forward recognition camera is 10 V or more for 2 seconds or more. ·
The LDA main switch is on. ·
Vehicle speed is 1 km/h (or 1 mph) or more. |
Turn the LDA main switch on and then drive the vehicle at a speed of 1 km/h (or 1 mph) or more for 7 seconds or more. | ·
Lane departure alert indicator light illuminates yellow. ·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
| U0101 | Lost Communication with TCM | The forward recognition camera does not receive data from the ECM for 5 seconds or more. | All conditions are met:
·
The power source voltage (IGB terminal voltage) of the forward recognition camera is 10 V or more for 2 seconds or more. ·
The LDA main switch is on. ·
Vehicle speed is 1 km/h (or 1 mph) or more. |
Turn the LDA main switch on and then drive the vehicle at a speed of 1 km/h (or 1 mph) or more for 7 seconds or more. | ·
Lane departure alert indicator light illuminates yellow. ·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
| U0123 | Lost Communication with Yaw Rate Sensor Module | The forward recognition camera does not receive data from the airbag sensor assembly for 5 seconds or more. | All conditions are met:
·
The power source voltage (IGB terminal voltage) of the forward recognition camera is 10 V or more for 2 seconds or more. ·
The LDA main switch is on. ·
Vehicle speed is 1 km/h (or 1 mph) or more. |
Turn the LDA main switch on and then drive the vehicle at a speed of 1 km/h (or 1 mph) or more for 7 seconds or more. | ·
Lane departure alert indicator light illuminates yellow. ·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication with Steering Angle Sensor Module | The forward recognition camera does not receive data from the steering sensor for 5 seconds or more. | Both conditions are met:
·
The power source voltage (IGB terminal voltage) of the forward recognition camera is 10 V or more for 2 seconds or more. ·
The LDA main switch is on. |
Turn the ignition switch to ON, turn the LDA main switch on and wait for at least 7 seconds. | ·
Lane departure alert indicator light illuminates yellow. ·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The forward recognition camera does not receive data from the skid control ECU (brake actuator assembly) for 5 seconds or more. | Both conditions are met:
·
The power source voltage (IGB terminal voltage) of the forward recognition camera is 10 V or more for 2 seconds or more. ·
The LDA main switch is on. |
Turn the ignition switch to ON, turn the LDA main switch on and wait for at least 7 seconds. | ·
Lane departure alert indicator light illuminates yellow. ·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
| U0131 | Lost Communication with Power Steering Control Module | The forward recognition camera does not receive data from the power steering ECU assembly for 5 seconds or more. | Both conditions are met:
·
The power source voltage (IGB terminal voltage) of the forward recognition camera is 10 V or more for 2 seconds or more. ·
The LDA main switch is on. |
Turn the ignition switch to ON, turn the LDA main switch on and wait for at least 7 seconds. | ·
Lane departure alert indicator light illuminates yellow. ·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Body Control Module "B" | The forward recognition camera does not receive data from the main body ECU (multiplex network body ECU) for 5 seconds or more. | Both conditions are met:
·
The power source voltage (IGB terminal voltage) of the forward recognition camera is 10 V or more for 2 seconds or more. ·
The LDA main switch is on. |
Turn the ignition switch to ON, turn the LDA main switch on and wait for at least 7 seconds. | ·
Lane departure alert indicator light illuminates yellow. ·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Instrument Panel Cluster (IPC) Control Module (Combination Meter) | The forward recognition camera does not receive data from the combination meter assembly for 50 seconds or more. | Both conditions are met:
·
The power source voltage (IGB terminal voltage) of the forward recognition camera is 10 V or more for 2 seconds or more. ·
The LDA main switch is on. |
Turn the ignition switch to ON, turn the LDA main switch on and wait for at least 52 seconds. | ·
Lane departure alert indicator light illuminates yellow. ·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
| U0235* | Lost Communication with Cruise Control Front Distance Range Sensor | The forward recognition camera does not receive data from the millimeter wave radar sensor assembly for 5 seconds or more. | Both conditions are met:
·
The power source voltage (IGB terminal voltage) of the forward recognition camera is 10 V or more for 2 seconds or more. ·
The LDA main switch is on. |
Turn the ignition switch to ON, turn the LDA main switch on and wait for at least 7 seconds. | ·
Lane departure alert indicator light illuminates yellow. ·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
| U023A* | Lost Communication with Image Processing Module "A" | The power steering ECU assembly does not receive data from the forward recognition camera for 5 seconds or more. | Both conditions are met:
·
The power source voltage (IGB terminal voltage) of the forward recognition camera is 10 V or more for 2 seconds or more. ·
The LDA main switch is on. |
Turn the ignition switch to ON, turn the LDA main switch on and wait for at least 7 seconds. | ·
Lane departure alert indicator light illuminates yellow. ·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
| U1104* | Lost Communication with Driving Support ECU | The forward recognition camera does not receive data from the driving support ECU assembly for 5 seconds or more. | Both conditions are met:
·
The power source voltage (IGB terminal voltage) of the forward recognition camera is 10 V or more for 2 seconds or more. ·
The LDA main switch is on. |
Turn the ignition switch to ON, turn the LDA main switch on and wait for at least 7 seconds. | ·
Lane departure alert indicator light illuminates yellow. ·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
Forward Recognition Camera / GTS Display "Front Recognition Camera"
This ECU uses the CAN communication system for DTC communication.
*1: Refer to Front Recognition Camera System.
Click hereEngine / Hybrid System>CRUISE CONTROL>FORWARD RECOGNITION CAMERA SYSTEM>U0235
*2: Blinks when the pre-collision system is malfunctioning.
*3: w/ Automatic High Beam System
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM/PCM "A" | The forward recognition camera does not receive data from the ECM for 5 seconds or more. | All conditions are met:
·
The power source voltage (IGB terminal voltage) of the forward recognition camera is 10 V or more for 2 seconds or more. ·
Vehicle speed is 1 km/h (or 1 mph) or more. ·
Automatic high beam main switch is on.*3 |
Turn the automatic high beam main switch on and then drive the vehicle at a speed of 1 km/h (or 1 mph) or more for 7 seconds or more. | ·
Displays messages on the multi-information display. ·
PCS indicator light blinks.*2 ·
Master warning light illuminates.*3 |
DTC is stored until it is cleared using the GTS. |
| U0101*3 | Lost Communication with TCM | The forward recognition camera does not receive data from the ECM for 5 seconds or more. | All conditions are met:
·
The power source voltage (IGB terminal voltage) of the forward recognition camera is 10 V or more for 2 seconds or more. ·
Vehicle speed is 1 km/h (or 1 mph) or more. ·
Automatic high beam main switch is on. |
Turn the automatic high beam main switch on and then drive the vehicle at a speed of 1 km/h (or 1 mph) or more for 7 seconds or more. | ·
Displays messages on the multi-information display. ·
Master warning light illuminates. |
DTC is stored until it is cleared using the GTS. |
| U0123 | Lost Communication with Yaw Rate Sensor Module | The forward recognition camera does not receive data from the airbag sensor assembly for 5 seconds or more. | All conditions are met:
·
The power source voltage (IGB terminal voltage) of the forward recognition camera is 10 V or more for 2 seconds or more. ·
Vehicle speed is 1 km/h (or 1 mph) or more. ·
Automatic high beam main switch is on.*3 |
Turn the automatic high beam main switch on and then drive the vehicle at a speed of 1 km/h (or 1 mph) or more for 7 seconds or more. | ·
Displays messages on the multi-information display. ·
PCS indicator light blinks.*2 ·
Master warning light illuminates.*3 |
DTC is stored until it is cleared using the GTS. |
| U0126*3 | Lost Communication with Steering Angle Sensor Module | The forward recognition camera does not receive data from the steering sensor for 5 seconds or more. | Both conditions are met:
·
The power source voltage (IGB terminal voltage) of the forward recognition camera is 10 V or more for 2 seconds or more. ·
Automatic high beam main switch is on. |
Turn the ignition switch to ON, turn the automatic high beam main switch on and wait for at least 7 seconds. | ·
Displays messages on the multi-information display. ·
Master warning light illuminates. |
DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The forward recognition camera does not receive data from the skid control ECU (brake actuator assembly) for 5 seconds or more. | Both conditions are met:
·
The power source voltage (IGB terminal voltage) of the forward recognition camera is 10 V or more for 2 seconds or more. ·
Automatic high beam main switch is on.*3 |
Turn the ignition switch to ON, turn the automatic high beam main switch on and wait for at least 7 seconds. | ·
Displays messages on the multi-information display. ·
PCS indicator light blinks.*2 ·
Master warning light illuminates.*3 |
DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Body Control Module "B" | The forward recognition camera does not receive data from the main body ECU (multiplex network body ECU) for 5 seconds or more. | The power source voltage (IGB terminal voltage) of the forward recognition camera is 10 V or more for 2 seconds or more. | Turn the ignition switch to ON and wait for at least 7 seconds. | ·
Displays messages on the multi-information display. ·
PCS indicator light blinks. |
DTC is stored until it is cleared using the GTS. |
| U0235*1 | Lost Communication with Cruise Control Front Distance Range Sensor | The forward recognition camera does not receive data from the millimeter wave radar sensor assembly for 5 seconds or more. | Both conditions are met:
·
The power source voltage (IGB terminal voltage) of the forward recognition camera is 10 V or more for 2 seconds or more. ·
Automatic high beam main switch is on.*3 |
Turn the ignition switch to ON, turn the automatic high beam main switch on and wait for at least 7 seconds. | ·
Displays messages on the multi-information display. ·
PCS indicator light blinks.*2 ·
Master warning light illuminates.*3 |
DTC is stored until it is cleared using the GTS. |
| U1104*1 | Lost Communication with Driving Support ECU | The forward recognition camera does not receive data from the driving support ECU assembly for 5 seconds or more. | The power source voltage (IGB terminal voltage) of the forward recognition camera is 10 V or more for 2 seconds or more. | Turn the ignition switch to ON and wait for at least 7 seconds. | ·
Displays messages on the multi-information display. ·
PCS indicator light blinks.*2 |
DTC is stored until it is cleared using the GTS. |
Forward Recognition Camera / GTS Display "Road Sign Assist"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Lost Communication with ECM/PCM "A" | The forward recognition camera does not receive data from the ECM for 5 seconds or more. | All conditions are met:
·
The power source voltage (IGB terminal voltage) of the forward recognition camera is 10 V or more for 2 seconds or more. ·
Vehicle speed is 1 km/h (or 1 mph) or more. ·
The road sign assist system is operating. |
Drive the vehicle at a speed of 1 km/h (or 1 mph) or more for 7 seconds or more. | ·
Master warning light illuminates. ·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
| U0101 | Lost Communication with TCM | The forward recognition camera does not receive data from the ECM for 5 seconds or more. | All conditions are met:
·
The power source voltage (IGB terminal voltage) of the forward recognition camera is 10 V or more for 2 seconds or more. ·
Vehicle speed is 1 km/h (or 1 mph) or more. ·
The road sign assist system is operating. |
Drive the vehicle at a speed of 1 km/h (or 1 mph) or more for 7 seconds or more. | ·
Master warning light illuminates. ·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
| U0123 | Lost Communication with Yaw Rate Sensor Module | The forward recognition camera does not receive data from the airbag sensor assembly for 5 seconds or more. | All conditions are met:
·
The power source voltage (IGB terminal voltage) of the forward recognition camera is 10 V or more for 2 seconds or more. ·
Vehicle speed is 1 km/h (or 1 mph) or more. ·
The road sign assist system is operating. |
Drive the vehicle at a speed of 1 km/h (or 1 mph) or more for 7 seconds or more. | ·
Master warning light illuminates. ·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The forward recognition camera does not receive data from the skid control ECU (brake actuator assembly) for 5 seconds or more. | Both conditions are met:
·
The power source voltage (IGB terminal voltage) of the forward recognition camera is 10 V or more for 2 seconds or more. ·
The road sign assist system is operating. |
Turn the ignition switch to ON and wait at least 7 seconds. | ·
Master warning light illuminates. ·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
| U0142 | Lost Communication with Body Control Module "B" | The forward recognition camera does not receive data from the main body ECU (multiplex network body ECU) for 5 seconds or more. | Both conditions are met:
·
The power source voltage (IGB terminal voltage) of the forward recognition camera is 10 V or more for 2 seconds or more. ·
The road sign assist system is operating. |
Turn the ignition switch to ON and wait at least 7 seconds. | ·
Master warning light illuminates. ·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
| U0155 | Lost Communication with Instrument Panel Cluster (IPC) Control Module (Combination Meter) | The forward recognition camera does not receive data from the combination meter assembly for 50 seconds or more. | Both conditions are met:
·
The power source voltage (IGB terminal voltage) of the forward recognition camera is 10 V or more for 2 seconds or more. ·
The road sign assist system is operating. |
Turn the ignition switch to ON and wait at least 52 seconds. | ·
Master warning light illuminates. ·
Displays messages on the multi-information display. |
DTC is stored until it is cleared using the GTS. |
Telematics Transceiver / GTS Display "Telematics"
This ECU uses the CAN communication system for DTC communication.
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0100 | Engine ECU Communication | The telematics transceiver does not receive data from the ECM for 15 seconds or more. | The ignition switch is ON for 10 seconds or more. | Turn the ignition switch to ON and wait at least 25 seconds. | - | DTC is stored until it is cleared using the GTS. |
Parking Assist ECU / GTS Display "Panoramic View Monitor"
This ECU uses the CAN communication system for DTC communication.
*: Refer to Panoramic View Monitor System.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>U1000
| DTC | Detection Item | DTC Detection Condition | DTC Detection Pre-condition | DTC Check Procedure | Warning Indication in Meter | DTC Storage Method |
|---|---|---|---|---|---|---|
| U0073 | Control Module Communication Bus Off | The parking assist ECU does not send/receive data for 13 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the parking assist ECU is 7.5 V or more. |
Turn the ignition switch to ON and wait at least 16 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0100 | Lost Communication with ECM/PCM "A" | The parking assist ECU does not receive data from the ECM for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the parking assist ECU is 7.5 V or more. |
Turn the ignition switch to ON and wait at least 13 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0126 | Lost Communication with Steering Angle Sensor Module | The parking assist ECU does not receive data from the steering sensor for 12 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the parking assist ECU is 7.5 V or more. |
Turn the ignition switch to ON and wait at least 15 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0129 | Lost Communication with Brake System Control Module | The parking assist ECU does not receive data from the skid control ECU (brake actuator assembly) for 10 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the parking assist ECU is 7.5 V or more. |
Turn the ignition switch to ON and wait at least 13 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0140 | Lost Communication with Body Control Module | The parking assist ECU does not receive data from the main body ECU (multiplex network body ECU) for 11 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the parking assist ECU is 7.5 V or more. |
Turn the ignition switch to ON and wait at least 14 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U0233 | Lost Communication with Blind Spot Monitor Master Module | The parking assist ECU does not receive data from the blind spot monitor sensor LH for 11 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the parking assist ECU is 7.5 V or more. |
Turn the ignition switch to ON and wait at least 14 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U1000* | CAN Communication Failure (Message Registry) | The parking assist ECU does not send/receive data. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the parking assist ECU is 7.5 V or more. |
Turn the ignition switch to ON and wait at least 3 seconds. | - | DTC is stored until it is cleared using the GTS. |
| U1110 | Lost Communication with Clearance Sonar Module | The parking assist ECU does not receive data from the clearance warning ECU assembly for 11 seconds or more. | Both conditions are met:
·
The ignition switch is ON for 3 seconds or more. ·
The power source voltage of the parking assist ECU is 7.5 V or more. |
Turn the ignition switch to ON and wait at least 14 seconds. | - | DTC is stored until it is cleared using the GTS. |
Central Gateway ECU (Network Gateway ECU) / GTS Display "Central Gateway"
The central gateway ECU (network gateway ECU) is connected to the CAN communication system, but the central gateway ECU (network gateway ECU) does not store or output CAN communication DTCs.
Steering Sensor / GTS Display "-"
The steering sensor is connected to the CAN communication system, but the steering sensor does not store or output CAN communication DTCs.
Position Control ECU and Switch Assembly / GTS Display "Driver Seat"
The position control ECU and switch assembly is connected to the CAN communication system, but the position control ECU and switch assembly does not store or output CAN communication DTCs.
Airbag Sensor Assembly / GTS Display "SRS Airbag"
The airbag sensor assembly is connected to the CAN communication system, but the airbag sensor assembly does not store or output CAN communication DTCs.
Millimeter Wave Radar Sensor Assembly / GTS Display "-"
The millimeter wave radar sensor assembly is connected to the CAN communication system, but the millimeter wave radar sensor assembly does not store or output CAN communication DTCs.
CAN BUS WAVEFORMS
The following waveforms are measured between terminals CANH and GND, and terminals CANL and GND of the central gateway ECU (network gateway ECU). (Use this as a reference for diagnosis of CAN communication lines.)
When malfunctions in multiple ECUs are suspected based on the CAN bus check and DTCs checked using the GTS, check the resistance of the CAN bus using an ohmmeter first. If no problems are found, check the following waveforms.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
If a waveform is not similar to one of the following 3 patterns (Group 1), then an open in a CAN main bus line, an open in a CAN branch line, or a short between a CAN line (CANH or CANL) and ground is suspected (Group 2).
Wiggle the connector and wire harness to check if the waveform changes.
CAN bus waveforms (Group 1)
Normal waveform
Open in both of the lines (CANH and CANL) of a CAN branch
Waveforms (waveforms shown using dotted lines) are not present from an ECU or sensor connected to a CAN branch with an open circuit in both lines. (Waveforms from other ECUs or sensors are normal.)
Because this waveform is similar to a normal waveform, instead of using the waveform, the malfunctioning part can be narrowed down by performing a CAN bus check.
Short between the CAN bus lines (CANH and CANL)
Waveforms disappear.
If the malfunction is in an ECU, disconnecting the ECU will change the waveform. If the waveform does not change, a malfunction in the wire harness is suspected.
CAN bus waveforms (reference) (Group 2)
The following CAN bus waveforms can be used only as reference. The actual measured waveform may differ significantly depending on the location of the open or short circuit.
Open in a CAN branch line (CANH)
An abnormal waveform is output from an ECU with an open in one of its CAN branch lines. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.
Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. The waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch line is disconnected.
Open in a CAN branch line (CANL)
An abnormal waveform is output from an ECU with an open in one of its CAN branch lines. Because this abnormal output interferes with the signals from other ECUs, the output of other ECUs will also appear abnormal.
Narrow down the malfunctioning part by checking DTCs or performing a CAN bus check, or by checking waveform changes when ECUs or sensors are disconnected. The waveform will change to one for an open in both sides of a CAN branch when the ECU or sensor with an open CAN branch line is disconnected.
Open in a CAN main bus line (CANH)
Waveforms of ECUs or sensors that are closer to the central gateway ECU (network gateway ECU) than the open part are almost normal.
Waveforms of ECUs or sensors that are on the opposite side of the central gateway ECU (network gateway ECU) from the open part are abnormal.
An open in a CAN main bus line can be confirmed by measuring the resistance between the CANH and CANL terminals of any CAN branch.
Short between a CAN bus line (CANH) and ground
Narrow down the shorted part by checking for waveform changes when disconnecting connectors from the CAN junction connectors or when disconnecting ECUs or sensors.
A short to ground in the CANH line can be confirmed by measuring the resistance between CANH and ground using an ohmmeter.
Short between a CAN bus line (CANL) and ground
Narrow down the shorted part by checking for waveform changes when disconnecting connectors from the CAN junction connectors or when disconnecting ECUs or sensors.
A short to ground in the CANL line can be confirmed by measuring the resistance between CANL and ground using an ohmmeter.
DATA SENDING/RECEIVING TABLE
Data sending/receiving table
If Data List items related to sent/received data are not displayed properly, the part for which communication is interrupted can be determined using the table below.
| Data Content | Data Detected and Sent by | Data Received by | Relevant Data List Item | ||
|---|---|---|---|---|---|
| Can be Checked in the Data List | Cannot be Checked in the Data List | Selected System*7 | Data List Item | ||
| Accelerator position | ECM | Skid control ECU (brake actuator assembly) | ·
Navigation receiver assembly ·
Radio and display receiver assembly ·
Power steering ECU assembly ·
4WD ECU assembly ·
Driving support ECU assembly ·
Forward recognition camera |
Engine and ECT | Accelerator Position |
| Engine | Accelerator Position | ||||
| ABS/VSC/TRC | Accelerator Opening Angle % | ||||
| Engine speed | ECM | ·
Power steering ECU assembly ·
Certification ECU (smart key ECU assembly) ·
Combination meter assembly ·
Skid control ECU (brake actuator assembly) |
·
Navigation receiver assembly ·
Radio and display receiver assembly ·
Airbag sensor assembly ·
Air conditioning amplifier assembly ·
Main body ECU (multiplex network body ECU) ·
4WD ECU assembly |
Engine and ECT | Engine Speed |
| Engine | Engine Speed | ||||
| EMPS | Engine Revolution | ||||
| Power Source Control | Engine Condition | ||||
| Starting Control | Engine Speed | ||||
| Combination Meter | Engine Rpm | ||||
| ABS/VSC/TRC | Engine Revolutions | ||||
| Engine coolant temperature | ECM | ·
Air conditioning amplifier assembly ·
4WD ECU assembly ·
Combination meter assembly |
·
Navigation receiver assembly ·
Radio and display receiver assembly ·
Skid control ECU (brake actuator assembly) |
Engine and ECT | Coolant Temp |
| Engine | Coolant Temperature | ||||
| Air Conditioner | Engine Coolant Temp | ||||
| Four Wheel Drive | Engine Coolant Temperature | ||||
| Combination Meter | Coolant Temperature | ||||
| Vehicle speed | Skid control ECU (brake actuator assembly) | ·
Navigation receiver assembly ·
Radio and display receiver assembly ·
ECM ·
Power steering ECU assembly ·
Combination meter assembly*3 ·
Blind spot monitor sensor LH ·
Television camera assembly ·
Parking assist ECU |
·
Telematics transceiver ·
Airbag sensor assembly ·
Main body ECU (multiplex network body ECU) ·
Driving support ECU assembly ·
Forward recognition camera |
ABS/VSC/TRC | Vehicle Speed |
| Navigation System | Vehicle Speed | ||||
| Engine and ECT | Vehicle Speed | ||||
| Engine | Vehicle Speed | ||||
| EMPS | Meter Vehicle Velocity | ||||
| Combination Meter | Vehicle Speed Meter | ||||
| Blind Spot Monitor Master | Vehicle Speed | ||||
| IPA/Parking Assist Monitor | Wheel Speed Sensor (4wheel) | ||||
| Panoramic View Monitor | Wheel Speed Sensor (4wheel) | ||||
| Combination meter assembly*3 | ·
Position control ECU and switch assembly ·
Clearance warning ECU assembly ·
Certification ECU (smart key ECU assembly) |
·
Multiplex network door ECU ·
Air conditioning amplifier assembly ·
Main body ECU (multiplex network body ECU) |
Combination Meter | Vehicle Speed Meter | |
| Driver Seat | Vehicle Speed | ||||
| Clearance Sonar | Vehicle Speed Info | ||||
| Power Source Control | Vehicle Speed Signal | ||||
| Wheel speed | Skid control ECU (brake actuator assembly) | ·
Headlight leveling ECU assembly ·
4WD ECU assembly |
·
Airbag sensor assembly ·
ECM ·
Power steering ECU assembly ·
Blind spot monitor sensor LH ·
Driving support ECU assembly ·
Forward recognition camera |
ABS/VSC/TRC | FR Wheel Speed |
| FL Wheel Speed | |||||
| RR Wheel Speed | |||||
| RL Wheel Speed | |||||
| HL AutoLeveling | Front Right Wheel Speed Value | ||||
| Front Left Wheel Speed Value | |||||
| Four Wheel Drive | FR Wheel Speed | ||||
| FL Wheel Speed | |||||
| RR Wheel Speed | |||||
| RL Wheel Speed | |||||
| Shift position | ECM | ·
Navigation receiver assembly ·
Radio and display receiver assembly ·
Position control ECU and switch assembly ·
Clearance warning ECU assembly ·
Certification ECU (smart key ECU assembly) ·
Blind spot monitor sensor LH |
·
Multiplex network door ECU ·
Airbag sensor assembly ·
Main body ECU (multiplex network body ECU) ·
Combination meter assembly*2 ·
Television camera assembly ·
Driving support ECU assembly ·
Forward recognition camera ·
Parking assist ECU |
Engine and ECT | Neutral Position SW Signal |
| Engine | Neutral Position SW | ||||
| Navigation System | Reverse Signal | ||||
| Driver Seat | P Switch | ||||
| Clearance Sonar | Parking Signal | ||||
| Reverse Signal | |||||
| Power Source Control | Shift P Signal | ||||
| Blind Spot Monitor Master | Reverse (Only for AT/CVT) | ||||
| Ambient temperature | Air conditioning amplifier assembly | ·
ECM ·
4WD ECU assembly ·
Combination meter assembly |
·
Navigation receiver assembly ·
Radio and display receiver assembly ·
Main body ECU (multiplex network body ECU) ·
Skid control ECU (brake actuator assembly) ·
Driving support ECU assembly ·
Forward recognition camera |
Air Conditioner | Ambient Temp Sensor |
| Engine and ECT | Ambient Temp for A/C | ||||
| Engine | Ambient Temp for A/C | ||||
| Four Wheel Drive | Ambient Temperature | ||||
| Combination Meter | Ambient Temperature | ||||
| Driver door courtesy switch | Main body ECU (multiplex network body ECU) | - | ·
Navigation receiver assembly ·
Radio and display receiver assembly ·
Certification ECU (smart key ECU assembly) ·
Combination meter assembly*2 ·
Forward recognition camera ·
Parking assist ECU |
Main Body | FL Door Courtesy SW |
| FR Door Courtesy SW | |||||
| Steering angle sensor | Steering sensor | ·
Power steering ECU assembly ·
4WD ECU assembly ·
Skid control ECU (brake actuator assembly) ·
Blind spot monitor sensor LH |
·
Navigation receiver assembly ·
Radio and display receiver assembly ·
Airbag sensor assembly ·
ECM ·
Television camera assembly ·
Driving support ECU assembly ·
Forward recognition camera ·
Parking assist ECU |
EMPS | Steering Angle Velocity |
| Four Wheel Drive | Steering Angle Value | ||||
| ABS/VSC/TRC | Steering Angle Sensor | ||||
| Blind Spot Monitor Master | Steering Angle | ||||
| Yaw rate sensor | Airbag sensor assembly | ·
4WD ECU assembly ·
Skid control ECU (brake actuator assembly) ·
Blind spot monitor sensor LH |
·
Driving support ECU assembly ·
Forward recognition camera |
Four Wheel Drive | Yaw Rate Value |
| ABS/VSC/TRC | Yaw Rate Sensor | ||||
| Blind Spot Monitor Master | Yaw Rate Sensor | ||||
| Deceleration Sensor | Airbag sensor assembly | ·
4WD ECU assembly ·
Skid control ECU (brake actuator assembly) |
·
ECM ·
Skid control ECU (brake actuator assembly) ·
Driving support ECU assembly ·
Forward recognition camera |
Four Wheel Drive | Lateral G |
| Forward and Rearward G | |||||
| ABS/VSC/TRC | Deceleration Sensor | ||||
| Deceleration Sensor2 | |||||
| Ignition switch condition | Main body ECU (multiplex network body ECU) | ·
Multiplex network door ECU ·
Position control ECU and switch assembly |
·
Outer mirror control ECU assembly (for driver side) ·
Outer mirror control ECU assembly (for front passenger side) ·
Certification ECU (smart key ECU assembly) ·
Television camera assembly |
Main Body | IG SW |
| Back Door | IG SW | ||||
| Driver Seat | Ignition Switch | ||||
| Driver side buckle switch signal | Airbag sensor assembly | - | ·
Telematics transceiver ·
Main body ECU (multiplex network body ECU) |
SRS Airbag | Left side Buckle SW |
| Main body ECU (multiplex network body ECU)*4 | - | ·
Telematics transceiver ·
Combination meter assembly*2 ·
Forward recognition camera |
- | - | |
| Passenger side buckle switch signal | Airbag sensor assembly | Combination meter assembly | Telematics transceiver | SRS Airbag | Right side Buckle SW |
| Combination Meter | P-Seatbelt Buckle SW | ||||
| Headlight switch | Main body ECU (multiplex network body ECU) | - | ·
Headlight leveling ECU assembly ·
ECM ·
Blind spot monitor sensor LH ·
Driving support ECU assembly ·
Combination meter assembly |
Main Body | Dimmer SW |
| Head Light SW (Tail) | |||||
| Side turn signal | Combination meter assembly*2 | ·
Blind spot monitor sensor LH ·
Forward recognition camera ·
Driving support ECU assembly |
- | Blind spot monitor Master | Turn Switch State |
| LKA/LDA | Turn Signal Switch (Right) | ||||
| Turn Signal Switch (Left) | |||||
| Pre-Collision 2 | Turn Light RH | ||||
| Turn Light LH | |||||
| ECM power source voltage*1 | ECM | - | - | Engine and ECT | Battery Voltage |
| ECM power source voltage*1 | ECM | - | - | Engine | Battery Voltage |
| Combination meter assembly power source voltage*1 | Combination meter assembly | - | - | Combination Meter | +B Voltage Value |
| Skid control ECU (brake actuator assembly) power source voltage*1 | Skid control ECU (brake actuator assembly) | - | - | ABS/VSC/TRC | BS1 Voltage Value |
| Power steering ECU assembly power source voltage*1 | Power steering ECU assembly | - | - | EMPS | IG Power Supply |
| Navigation receiver assembly power source voltage*1 | Navigation receiver assembly | - | - | Navigation System | Battery Voltage |
| Radio and display receiver assembly power source voltage*1 | Radio and display receiver assembly | - | - | Navigation System | Battery Voltage |
| Solar sensor*1 | Air conditioning amplifier assembly | - | - | Air Conditioner | Solar Sensor (D side) |
| Driver door touch sensor*1 | Certification ECU (smart key ECU assembly) | - | - | Entry&Start | D-Door Touch Sensor |
| Clearance sonar main switch condition*1 | Clearance warning ECU assembly | - | - | Clearance Sonar | Main Switch |
| Transfer control solenoid current*1 | 4WD ECU assembly | - | - | Four Wheel Drive | SLC Solenoid Current |
| Blind spot monitor sensor LH power source voltage*1 | Blind spot monitor sensor LH | - | - | Blind Spot Monitor Master | Power Supply Voltage |
| Outer mirror control ECU assembly (for driver side) power source voltage*1 | Outer mirror control ECU assembly (for driver side) | - | - | ·
Mirror L*5 ·
Mirror R*6 |
+B Voltage Input Value |
| Outer mirror control ECU assembly (for front passenger side) power source voltage*1 | Outer mirror control ECU assembly (for front passenger side) | - | - | ·
Mirror R*5 ·
Mirror L*6 |
+B Voltage Input Value |
| Position control ECU and switch assembly power source voltage*1 | Position control ECU and switch assembly | - | - | Driver Seat | Power Voltage |
| Headlight leveling ECU assembly power source voltage*1 | Headlight leveling ECU assembly | - | - | HL AutoLeveling | +B |
| Panoramic view monitor main switch condition*1 | Parking assist ECU | - | - | Panoramic View Monitor | Camera Changing SW Signal Status |
*1: Whether the ECU that sends data is functioning or not can be judged by using the GTS to check items such as switches or sensors that send signals to the ECU via direct lines.
*2: Although the received contents cannot be checked in the Data List, whether or not the data is received normally can be checked by observing the combination meter assembly.
*3: The combination meter assembly receives a vehicle speed signal from the skid control ECU (brake actuator assembly) and sends the signal to other ECUs.
*4: The main body ECU (multiplex network body ECU) receives a driver seat buckle switch signal from the airbag sensor assembly and sends the signal to other ECUs.
*5: for LHD
*6: for RHD
*7: According to the display on the GTS, read the Data List.
Enter the following menus: Powertrain / Engine and ECT / Data List.
Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST
Enter the following menus: Powertrain / Engine / Data List.
Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
Enter the following menus: Chassis / EMPS / Data List.
Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>DATA LIST / ACTIVE TEST
Enter the following menus: Body Electrical / Power Source Control / Data List.
Enter the following menus: Body Electrical / Starting Control / Data List.
Enter the following menus: Body Electrical / Combination Meter / Data List.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST
Enter the following menus: Body Electrical / Air Conditioner / Data List.
for Automatic Air Conditioning System:Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)>DATA LIST / ACTIVE TEST
for Manual Air Conditioning System:Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)>DATA LIST / ACTIVE TEST
Enter the following menus: Chassis / Four Wheel Drive / Data List.
Click hereDrivetrain>MF1A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM>DATA LIST / ACTIVE TEST
Enter the following menus: Body Electrical / Navigation System / Data List.
w/o Navigation System for Radio and Display Type:Audio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DATA LIST / ACTIVE TEST
w/ Navigation System for Radio and Display Type:Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>DATA LIST / ACTIVE TEST
for Navigation Receiver Type: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Navigation Receiver Type)>DATA LIST / ACTIVE TEST
Enter the following menus: Body Electrical / Blind Spot Monitor Master / Data List.
Enter the following menus: Chassis / IPA/Parking Assist Monitor / Data List.
Enter the following menus: Body Electrical / Driver Seat / Data List.
Click hereVehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)>DATA LIST / ACTIVE TEST
Enter the following menus: Body Electrical / Clearance Sonar / Data List.
for 4 Sensor Type:Audio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM (for 4 Sensor Type)>DATA LIST / ACTIVE TEST
for 6 Sensor Type:Audio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM(for 6 Sensor Type)>DATA LIST / ACTIVE TEST
Enter the following menus: Body Electrical / HL AutoLeveling / Data List.
Enter the following menus: Body Electrical / Main Body / Data List.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DATA LIST / ACTIVE TEST
Enter the following menus: Body Electrical / Back Door / Data List.
Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>DATA LIST / ACTIVE TEST
Enter the following menus: Body Electrical / SRS Airbag / Data List.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DATA LIST / ACTIVE TEST
Enter the following menus: Chassis / LKA/LDA / Data List.
Enter the following menus: Body Electrical / Pre-Collision 2 / Data List.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DATA LIST / ACTIVE TEST
Enter the following menus: Body Electrical / Entry&Start / Data List.
Enter the following menus: Body Electrical / Mirror L or Mirror R / Data List.
Click hereVehicle Exterior>MIRROR (EXT)>POWER MIRROR CONTROL SYSTEM(w/ Memory)>DATA LIST / ACTIVE TEST
Enter the following menus: Chassis / Panoramic View Monitor / Data List.