Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2016.11
RM3160E _53 Suspension _060167 TIRE PRESSURE MONITORING _0296404 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  B1247  Tire Pressure Monitor Receiver Communication Stop  


DESCRIPTION

The main body ECU (multiplex network body ECU) and tire pressure warning ECU and receiver are connected using 2 direct lines that they use to communicate with each other.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B1247 Tire Pressure Monitor Receiver Communication Stop In diagnostic mode, an applicable RDA signal cannot be received within 10 seconds after a PRG signal is sent from the main body ECU (multiplex network body ECU).
·

Tire pressure warning ECU and receiver

·

Wire harness or connector

·

Main body ECU (multiplex network body ECU)


This DTC is for main body ECU (multiplex network body ECU)

WIRING DIAGRAM

C355819E08
1.333,0.5 1.583,0.698 0.25,0.198 10 false IG 1.177,1.063 1.604,1.26 0.427,0.198 10 false RDA 1.177,1.552 1.573,1.75 0.396,0.198 10 false PRG 1.167,2.146 1.625,2.344 0.458,0.198 10 false GND 1.604,0.406 2.021,0.656 0.417,0.25 10 false 1 1.615,0.979 2.031,1.229 0.417,0.25 10 false 4 1.615,1.479 2.031,1.729 0.417,0.25 10 false 5 1.604,2 1.958,2.188 0.354,0.188 10 false 12 2.365,0.688 4.542,1.365 2.177,0.677 10 false IG1 NO. 3 3.885,0.521 5.385,1.021 1.5,0.5 10 false from IG Circuit 5.417,1.979 5.813,2.146 0.396,0.167 10 false F19 5.417,2.156 7.042,3.021 1.625,0.865 10 false Main Body ECU (Multiplex Network Body ECU) 5.479,0.979 5.792,1.146 0.313,0.167 10 false 4 5.469,1.469 5.75,1.667 0.281,0.198 10 false 5 5.688,1.083 6.073,1.24 0.385,0.156 10 false RDA 5.688,1.583 6.031,1.75 0.344,0.167 10 false PRG 0.25,2.729 0.635,2.99 0.385,0.26 10 false M45 0.25,2.896 3.302,3.49 3.052,0.594 10 false Tire Pressure Warning ECU and Receiver

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initializationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registrationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver after the ECU has been replaced.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.



HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Disconnect the M45 tire pressure warning ECU and receiver connector.


b.

Disconnect the F19 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M45-4 (RDA) - F19-4 (RDA) Always Below 1 Ω
M45-4 (RDA) or F19-4 (RDA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF TIRE PRESSURE WARNING ECU AND RECEIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF TIRE PRESSURE WARNING ECU AND RECEIVER)
a.
C361354C04
0.333,0.833 0.75,1.083 0.417,0.25 0.75,1.583 0.917,1.583 0.917,1.583 1.24,1.26 true 2.719,1.719 2.552,1.719 2.552,1.719 2.219,1.469 true 0.396,0.854 0.854,1.052 0.458,0.198 10 false M45 0.552,1.5 0.833,1.75 0.281,0.25 10 false IG 2.802,1.635 3.26,1.833 0.458,0.198 10 false GND 0.073,0.073 0.385,0.271 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M45-12 (GND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M45-1 (IG) - Body ground Engine switch on (IG) 10 to 16 V



Result:
Proceed to
OK
NG



OK

3.REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER
a.

Replace the tire pressure warning ECU and receiver.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RECEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT
4.CHECK DTC OUTPUT
a.

Clear the DTCs.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DTC CHECK / CLEAR

Chassis > Tire Pressure Monitor > Clear DTCs
50002 203

b.

Turn the engine switch off.


c.

Turn the engine switch on (IG).


d.

Check for DTCs.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>DTC CHECK / CLEAR

Chassis > Tire Pressure Monitor > Trouble Codes
50001 203
OK:

DTC B1247 is not output.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)