Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 1AR-FE) › from 2016.11
RM3160E _51 Engine / Hybrid System _019684 CRUISE CONTROL _0296315 DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 1AR-FE) C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 1AR-FE)  P0571  Brake Switch "A" Circuit  


DESCRIPTION

Detection condition 1:
·

When the brake pedal is depressed, the stop light switch assembly sends a signal to the ECM. When the ECM receives this signal, it cancels the dynamic radar cruise control. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light signal circuit. The cancellation condition occurs when voltage is applied to terminal STP. When the brake is applied, voltage is normally applied to terminal STP of the ECM through the STOP fuse and the stop light switch assembly, and the ECM turns the dynamic radar cruise control system off.


Detection condition 2:
·

When the brakes are applied by the dynamic radar cruise control system, the skid control ECU (brake actuator assembly) operates the stop light switch assembly (stop light relay) to illuminate the stop lights.

If the ECM receives a stop light switch control relay malfunction signal from the skid control ECU (brake actuator assembly), DTC P0571 is stored.


DTC No. Detection Item DTC Detection Condition Trouble Area
P0571 Brake Switch "A" Circuit
Condition 1:
·

While the vehicle speed is 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, voltage of STP terminal and that of ST1- terminal of ECM are less than 1 V for approximately 0.5 seconds or more.


Condition 2:
·

While the vehicle speed is 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, the ECM detects the stop light switch assembly error signal from the skid control ECU (brake actuator assembly) for approximately 0.2 seconds or more.


Detection condition 1:
·

Stop light switch assembly

·

ECM

·

Harness or connector


Detection condition 2:
·

Pre-collision system



WIRING DIAGRAM

A395927E06
6.042,2.125 6.5,2.323 0.458,0.198 10 false ECM 5.271,0.604 5.729,0.802 0.458,0.198 10 false A43 5.281,1.396 5.74,1.594 0.458,0.198 10 false A43 5.677,0.5 6.135,0.698 0.458,0.198 10 false STP 5.677,1.302 6.135,1.5 0.458,0.198 10 false ST1- 5.323,0.385 5.781,0.583 0.458,0.198 10 false 11 5.313,1.188 5.771,1.385 0.458,0.198 10 false 24 5.385,3.281 6.906,3.677 1.521,0.396 10 false Certification ECU (Smart Key ECU Assembly) 5.094,3.281 5.552,3.479 0.458,0.198 10 false F10 5.75,2.865 6.302,3.063 0.552,0.198 10 false STP1 5.563,2.76 6.021,2.958 0.458,0.198 10 false 2 2.948,4.281 5.104,4.646 2.156,0.365 10 false Transmission Floor Shift Assembly (Shift Lock Control Unit) 2.646,4.281 3.656,4.479 1.01,0.198 10 false F48 4,3.896 4.458,4.094 0.458,0.198 10 false STP 4.375,3.792 5.073,3.979 0.698,0.188 10 false 6 2.146,3.26 5,3.5 2.854,0.24 10 false Skid Control ECU (Brake Actuator Assembly) 1.823,3.25 2.281,3.448 0.458,0.198 10 false A86 3.906,2.865 4.365,3.063 0.458,0.198 10 false STP2 4.354,2.76 4.813,2.958 0.458,0.198 10 false 5 3.573,1.729 4.031,1.927 0.458,0.198 10 false GND 3.031,2.104 4.896,2.323 1.865,0.219 10 false Stop Light Switch Assembly 2.688,2.104 3.146,2.302 0.458,0.198 10 false A87 3.385,1.615 3.844,1.813 0.458,0.198 10 false 2 3.583,1.24 4.042,1.438 0.458,0.198 10 false B 3.583,0.708 4.042,0.906 0.458,0.198 10 false B 3.385,1.115 3.844,1.313 0.458,0.198 10 false 6 3.406,0.615 3.865,0.813 0.458,0.198 10 false 7 2.469,1.385 2.927,1.583 0.458,0.198 10 false IG2 2.396,0.885 2.854,1.083 0.458,0.198 10 false STOP 0.49,1.219 1.698,1.469 1.208,0.25 10 false from IG2 Relay 0.521,0.719 1.969,1.01 1.448,0.292 10 false from ALT Fuse 4.135,0.604 4.594,0.802 0.458,0.198 10 false L 4.156,1.406 4.615,1.604 0.458,0.198 10 false L 4.344,1.292 4.802,1.49 0.458,0.198 10 false 5 4.344,0.49 4.802,0.688 0.458,0.198 10 false 3

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK FOR DTCs (PRE-COLLISION SYSTEM)
a.

Check for DTCs of the pre-collision system.

Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Pre-Collision 2 > Trouble Codes
50001 220
HINT:

When DTC P0571 is stored by the dynamic radar cruise control system, DTC C1A4B may be stored by the pre-collision system. Therefore, if DTC P0571 is stored, inspect the pre-collision system first.



Result:
Result Proceed to
DTC C1A4B is output A
DTC C1A4B is not output B



A

GO TO PRE-COLLISION SYSTEM

B

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
a.
A395526C03
1.479,0.302 1.875,0.521 0.396,0.219 0.792,1.823 1.292,1.156 true 1.469,1.844 1.969,1.177 true 2.26,1.156 2.76,0.49 true 0.146,0.135 0.458,0.292 0.313,0.156 10 false *a 0.615,1.844 1.073,2.042 0.458,0.198 10 false GND 1.427,1.844 1.885,2.042 0.458,0.198 10 false B 2.823,0.427 3.281,0.625 0.458,0.198 10 false B 1.552,0.344 2.01,0.542 0.458,0.198 10 false A87
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the A87 stop light switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A87-2 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A87-7 (B) - Body ground Always 11 to 14 V
A87-6 (B) - Body ground Engine switch on (IG) 11 to 14 V
A87-6 (B) - Body ground Engine switch off Below 1 V



Result:
Proceed to
OK
NG



OK

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (ECM - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A43 ECM connector.


b.

Disconnect the A87 stop light switch assembly connector.


c.

Disconnect the A86 skid control ECU (brake actuator assembly) connector.


d.

Disconnect the F10 certification ECU (smart key ECU assembly) connector.


e.

Disconnect the F48 transmission floor shift assembly (shift lock control unit) connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A43-24 (ST1-) - A87-5 (L) Always Below 1 Ω
A43-11 (STP) - A87-3 (L) Always Below 1 Ω
A43-24 (ST1-) or A87-5 (L) - Body ground Always 10 kΩ or higher
A43-11 (STP) or A87-3 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR