Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 2GR-FKS) › from 2016.11
RM3160E _51 Engine / Hybrid System _019684 CRUISE CONTROL _0296316 DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 2GR-FKS) C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 2GR-FKS)  P163081  Communication Error from VSC to ECM Invalid Serial Data Received  


DESCRIPTION

The skid control ECU (brake actuator assembly) sends signals such as cruise control cancel signals and brake demand response signals to the ECM when the dynamic radar cruise control system is operating.

DTC No. Detection Item DTC Detection Condition Trouble Area
P163081 Communication Error from VSC to ECM Invalid Serial Data Received While the vehicle speed is 36 km/h (22 mph) or more and the dynamic radar cruise control system is operating, communication data from the skid control ECU (brake actuator assembly) is logically inconsistent for approximately 0.5 seconds or more.
·

CAN communication circuit

·

Skid control ECU (brake actuator assembly)

·

ECM



CAUTION / NOTICE / HINT

NOTICE:

First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Using the GTS, check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN communication system DTCs are not output OK
CAN communication system DTCs are output NG



OK

2.CHECK FOR DTCs (RADAR CRUISE 1)

NG

2.CHECK FOR DTCs (RADAR CRUISE 1)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 2GR-FKS)>DTC CHECK / CLEAR

Powertrain > Radar Cruise1 > Clear DTCs
50002 374

b.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the following conditions are not met, the malfunction cannot be detected.

1.

Turn the engine switch on (IG).

2.

Turn the dynamic radar cruise control system on using the cruise control main switch (ON-OFF button).

3.

Drive the vehicle at 36 km/h (22 mph) or more for 0.5 seconds or more.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 2GR-FKS)>DTC CHECK / CLEAR

Powertrain > Radar Cruise1 > Trouble Codes
50001 374

Result:
Result Proceed to
DTC P163081 is not output A
DTC P163081 is output B



A

B

3.REPLACE BRAKE ACTUATOR ASSEMBLY
3.REPLACE BRAKE ACTUATOR ASSEMBLY
a.

Replace the brake actuator assembly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTCs (RADAR CRUISE 1)
4.CHECK FOR DTCs (RADAR CRUISE 1)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 2GR-FKS)>DTC CHECK / CLEAR

Powertrain > Radar Cruise1 > Clear DTCs
50002 374

b.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the following conditions are not met, the malfunction cannot be detected.

1.

Turn the engine switch on (IG).

2.

Turn the dynamic radar cruise control system on using the cruise control main switch (ON-OFF button).

3.

Drive the vehicle at 36 km/h (22 mph) or more for 0.5 seconds or more.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM(for 2GR-FKS)>DTC CHECK / CLEAR

Powertrain > Radar Cruise1 > Trouble Codes
50001 374

Result:
Result Proceed to
DTC P163081 is not output A
DTC P163081 is output B



A

END

B