Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM › from 2016.11
RM3160E _56 Audio / Visual / Telematics _060168 TELEMATICS _0296504 TELEMATICS SYSTEM C

TELEMATICS  TELEMATICS SYSTEM  B1573  Disconnect/Short in Telephone Antenna Circuit  B15CB  Telephone Antenna Disconnected  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the telephone antenna assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1573 Disconnect/Short in Telephone Antenna Circuit Telephone antenna assembly impedance (Ω) is lower than the malfunction threshold for 20 seconds when the engine switch is on (IG).
(Short circuit)
·

Telematics transceiver

·

Telephone antenna assembly

·

Floor wire

·

No. 2 antenna cord sub-assembly


B15CB Telephone Antenna Disconnected Telephone antenna assembly impedance (Ω) is higher than the malfunction threshold for 20 seconds when the engine switch is on (IG).
(Open circuit)
·

Telematics transceiver

·

Telephone antenna assembly

·

Floor wire

·

No. 2 antenna cord sub-assembly



WIRING DIAGRAM

E338342E09
1.146,0.396 1.385,0.583 0.24,0.188 10 false 4 0.281,1.083 0.927,1.271 0.646,0.188 10 false B 6.104,1.26 6.823,1.635 0.719,0.375 10 false Telematics Transceiver 2.094,0.688 2.438,0.865 0.344,0.177 10 false *2 3.417,0.354 3.625,0.521 0.208,0.167 10 false 2 3.833,0.354 4.01,0.51 0.177,0.156 10 false 2 3.406,0.552 3.615,0.719 0.208,0.167 10 false A 3.76,0.563 4.156,0.729 0.396,0.167 10 false L33 4.99,0.677 5.333,0.854 0.344,0.177 10 false *1 5.896,0.396 6.104,0.594 0.208,0.198 10 false 1 6.125,0.542 6.51,0.719 0.385,0.177 10 false TEL 6.115,1.083 6.51,1.25 0.396,0.167 10 false L31 1.583,2.51 4.646,2.708 3.063,0.198 10 false *2: No. 2 Antenna Cord Sub-assembly 0.25,1.271 2.302,1.542 2.052,0.271 10 false Telephone Antenna Assembly 1.594,2.188 4.656,2.385 3.063,0.198 10 false *1: Floor Wire

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>REGISTRATION


PROCEDURE

1.CHECK DTC
a.

Turn the engine switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG) and wait for 20 seconds.


d.

Turn the GTS on.


e.

Check for DTCs and check that no DTCs are output.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DTC CHECK / CLEAR

Body Electrical > Telematics > Trouble Codes
50001 233
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT TELEPHONE ANTENNA ASSEMBLY
2.INSPECT TELEPHONE ANTENNA ASSEMBLY
a.

Remove the telephone antenna assembly.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL


b.
E271865C14
1.969,1.479 2.229,1.729 false 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 2.26,1.708 2.573,1.906 0.313,0.198 10 false 4a
*a Component without harness connected
(Telephone Antenna Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 - 4a Always 4 to 11 kΩ



Result:
Proceed to
OK
NG



OK

3.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE TELEPHONE ANTENNA ASSEMBLY

3.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.

Remove the No. 2 antenna cord sub-assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL


b.
E271898C23
2.135,0.781 2.49,1.01 0.354,0.229 1.198,1.333 1.552,1.115 false 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 2.26,0.813 2.573,1.01 0.313,0.198 10 false B 1.021,1.302 1.333,1.5 0.313,0.198 10 false 4a
*a Component without harness connected
(No. 2 Antenna Cord Sub-assembly)


E170051C23
2.5,1 2.917,1.25 0.417,0.25 0.969,1.396 1.521,1.167 false 0.198,0.167 0.5,0.385 0.302,0.219 10 false *a 0.771,1.323 1.073,1.542 0.302,0.219 10 false 2a 2.646,1.042 2.948,1.26 0.302,0.219 10 false A
*a Component without harness connected
(No. 2 Antenna Cord Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 - B-4 Always Below 1 Ω
A-2a - B-4a Always Below 1 Ω
A-2 or B-4 - Body ground Always 10 kΩ or higher
A-2a or B-4a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT FLOOR WIRE

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

4.INSPECT FLOOR WIRE
a.

Disconnect the L31 and L33 floor wire connectors.


b.
E342834C07
0.854,1.063 1.26,1.302 0.406,0.24 1.917,1.344 2.208,1.656 false 1.667,1.344 1.333,1.688 false 0.135,0.125 0.448,0.323 0.313,0.198 10 false *a 0.958,1.115 1.573,1.313 0.615,0.198 10 false L31 2.229,1.667 2.542,1.875 0.313,0.208 10 false 1a 1.083,1.677 1.396,1.885 0.313,0.208 10 false TEL
*a Front view of floor wire connector
(to Telematics Transceiver)


E170034C10
1.469,0.219 1.885,0.469 0.417,0.25 2.104,1.031 2.448,1.302 false 2.427,1.333 3.344,1.531 0.917,0.198 10 false 2a 0.219,0.198 0.531,0.396 0.313,0.198 10 false *a 1.573,0.271 2.49,0.469 0.917,0.198 10 false L33
*a Front view of floor wire connector
(to No. 2 Antenna Cord Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L31-1 (TEL) - L33-2 (TEL) Always Below 1 Ω
L31-1a - L33-2a Always Below 1 Ω
L31-1 (TEL) or L33-2 (TEL) - Body ground Always 10 kΩ or higher
L31-1a or L33-2a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE TELEMATICS TRANSCEIVER

NG

REPLACE FLOOR WIRE

5.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT