These DTCs are stored when a malfunction occurs in the telephone antenna assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15C0 | GPS Antenna Disconnected (Short) | Current to the telephone antenna assembly is lower than the malfunction threshold for 20 seconds when the engine switch is on (IG).
(Short circuit) |
·
Telematics transceiver ·
Telephone antenna assembly ·
Floor wire ·
No. 2 antenna cord sub-assembly |
| B15C1 | GPS Antenna Disconnected (Open) | Current for telephone antenna assembly is higher than the malfunction threshold for 20 seconds when the engine switch is on (IG).
(Open circuit) |
·
Telematics transceiver ·
Telephone antenna assembly ·
Floor wire ·
No. 2 antenna cord sub-assembly |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>REGISTRATION
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG) and wait for 20 seconds.
Turn the GTS on.
Check for DTCs and check that no DTCs are output.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DTC CHECK / CLEAR
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Remove the No. 2 antenna cord sub-assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD>REMOVAL
| *a | Component without harness connected
(No. 2 Antenna Cord Sub-assembly) |
| *a | Component without harness connected
(No. 2 Antenna Cord Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-1 - B-2 | Always | Below 1 Ω |
| A-1a - B-2a | Always | Below 1 Ω |
| A-1 or B-2 - Body ground | Always | 10 kΩ or higher |
| A-1a or B-2a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the L32 and L33 floor wire connectors.
| *a | Front view of floor wire connector
(to Telematics Transceiver) |
| *a | Front view of floor wire connector
(to No. 2 Antenna Cord Sub-assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L32-1 (GPS) - L33-1 (GPS) | Always | Below 1 Ω |
| L32-1a - L33-1a | Always | Below 1 Ω |
| L32-1 (GPS) or L33-1 (GPS) - Body ground | Always | 10 kΩ or higher |
| L32-1a or L33-1a - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telephone antenna assembly with a new or known good one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL
Clear the DTCs.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telematics transceiver with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT