Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › TOYOTA PARKING ASSIST-SENSOR SYSTEM(for 6 Sensor Type) › from 2016.11
RM3160E _56 Audio / Visual / Telematics _019702 PARK ASSIST / MONITORING _0297894 TOYOTA PARKING ASSIST-SENSOR SYSTEM(for 6 Sensor Type) J

PARK ASSIST / MONITORING  TOYOTA PARKING ASSIST-SENSOR SYSTEM(for 6 Sensor Type)  Clearance Sonar Main Switch Circuit  


DESCRIPTION

When the back sonar or clearance sonar switch assembly is turned on, an on signal is sent to the clearance warning ECU assembly. The Toyota parking assist-sensor system operates according to this signal.

WIRING DIAGRAM

E289078E02
0.313,0.625 1.677,1.021 1.365,0.396 10 false from IG1 NO. 3 Relay 2.292,0.781 3.667,0.979 1.375,0.198 10 false IG1 NO. 3 3.365,0.531 3.521,0.729 0.156,0.198 10 false 9 4.594,0.51 4.75,0.708 0.156,0.198 10 false 6 3.135,0.948 3.448,1.146 0.313,0.198 10 false F5 3.115,1.135 5.135,1.802 2.021,0.667 10 false Back Sonar or Clearance Sonar Switch Assembly 5.552,0.625 6.167,0.823 0.615,0.198 10 false CLSW 5.281,0.521 5.594,0.719 0.313,0.198 10 false 38 5.469,1.26 5.927,1.458 0.458,0.198 10 false F87 5.448,1.448 7,1.885 1.552,0.438 10 false Clearance Warning ECU Assembly 3.542,0.521 3.854,0.719 0.313,0.198 10 false IG 4.219,0.521 4.677,0.719 0.458,0.198 10 false ECU

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Clearance Sonar / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Clearance Sonar > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Clearance Sonar ECU clearance warning ECU assembly information Normal or Abnormal Normal: clearance warning ECU assembly normal
Abnormal: clearance warning ECU assembly not normal
-
Body Electrical > Clearance Sonar > Data List
Tester Display
Clearance Sonar ECU
50003 170 35

Result:
Result Proceed to
"Normal" is displayed. A
"Abnormal" is displayed. B



A

2.READ VALUE USING GTS

B

2.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Clearance Sonar / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Clearance Sonar > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Main Switch Back sonar or clearance sonar switch assembly OFF or ON OFF: Back sonar or clearance sonar switch assembly off
ON: Back sonar or clearance sonar switch assembly on
-
Body Electrical > Clearance Sonar > Data List
Tester Display
Main Switch
50003 170 1

Result:
Result Proceed to
The display does not change as shown above when the back sonar or clearance sonar switch assembly is operated. A
The display changes as shown above when the back sonar or clearance sonar switch assembly is operated. B



A

3.INSPECT BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY

B

3.INSPECT BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY
a.

Remove the back sonar or clearance sonar switch assembly.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE SONAR MAIN SWITCH>REMOVAL


b.
E197324C18
1.583,1.375 1.375,1.698 false 2.021,1.375 2.24,1.698 false 2.177,1.719 2.583,1.979 0.406,0.26 10 false ECU 1.219,1.719 1.5,1.958 0.281,0.24 10 false IG 0.146,0.094 0.333,0.271 0.188,0.177 10 false *a
*a Component without harness connected
(Back Sonar or Clearance Sonar Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (IG) - 6 (ECU) Back sonar or clearance sonar switch assembly pushed Below 1 Ω
9 (IG) - 6 (ECU) Back sonar or clearance sonar switch assembly not pushed 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY - BATTERY)

NG

REPLACE BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY - BATTERY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F5-9 (IG) - Body ground Ignition switch ON 11 to 14 V
F5-9 (IG) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY)
a.

Disconnect the F87 clearance warning ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F87-38 (CLSW) - F5-6 (ECU) Always Below 1 Ω
F87-38 (CLSW) or F5-6 (ECU) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR