Home › Engine / Hybrid System › 2GR-FKS (COOLING) › WATER PUMP › from 2016.11
RM3160E _51 Engine / Hybrid System _060161 2GR-FKS COOLING _0297902 WATER PUMP A

2GR-FKS COOLING  WATER PUMP  INSTALLATION  


PROCEDURE

Hide 16100 1.INSTALL ENGINE WATER PUMP ASSEMBLY

a.
A394890N01
0.281,0.719 0.521,0.917 0.24,0.198 10 true A 2.688,0.76 2.927,0.958 0.24,0.198 10 true A 0.323,1.792 0.542,2.01 0.219,0.219 10 true B 0.792,1.844 1.01,2.063 0.219,0.219 10 true B 1.438,1.906 1.656,2.125 0.219,0.219 10 true B 1.094,1.781 1.313,2 0.219,0.219 10 true C 1.76,1.875 1.979,2.094 0.219,0.219 10 true C 2.135,1.583 2.354,1.802 0.219,0.219 10 true C 2.521,1.635 2.74,1.854 0.219,0.219 10 true B 2.958,1.26 3.177,1.479 0.219,0.219 10 true B 2.448,0.594 2.667,0.813 0.219,0.219 10 true C 2.313,0.083 2.531,0.302 0.219,0.219 10 true C 1.563,0.427 1.781,0.646 0.219,0.219 10 true C 1.083,0.667 1.302,0.885 0.219,0.219 10 true B 0.688,0.625 0.906,0.844 0.219,0.219 10 true C

Install a new water pump gasket and the engine water pump assembly together with the water pump pulley with the 15 bolts.

Torque:
Bolt (A) : 43 N*m (438 kgf*cm, 32 ft.*lbf)
Bolt (B) : 21 N*m (214 kgf*cm, 15 ft.*lbf)
Bolt (C) : 11 N*m (112 kgf*cm, 8 ft.*lbf)

Standard Length:
Item Length
Bolt (A) 60 mm (2.36 in.)
Bolt (B) 55 mm (2.17 in.)
Bolt (C) 22 mm (0.866 in.)


NOTICE:
·

Make sure that there is no oil on the threads of the bolts (A) and (B).

·

Do not start the engine for at least 1 hour after installation.




Hide 16173 2.INSTALL WATER PUMP PULLEY

a.

Temporarily install the water pump pulley with the 4 bolts.


b.
A478769C01
2.948,1.01 2.813,0.344 2.813,0.344 2.573,0.344 true 1.302,2.385 1.667,1.979 1.667,1.979 2.146,1.979 true 1.729,3.01 2.333,3.01 true 2.302,0.24 2.542,0.448 0.24,0.208 10 true *c 1.167,2.417 1.406,2.625 0.24,0.208 10 true *a 1.458,2.906 1.698,3.115 0.24,0.208 10 true *b 1.656,3.677 1.896,3.885 0.24,0.208 10 false *d
*a Protective Tape
*b Hold
*c Turn
*d Torque Wrench Fulcrum Length


Using a screwdriver or equivalent with its tip wrapped in protective tape, hold the water pump pulley.


c.

Using a 12 mm union nut wrench, fully tighten the 4 bolts.

Torque:
Specified tightening torque : 21 N*m (214 kgf*cm, 15 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 12 mm union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 19 N*m (194 kgf*cm, 14 ft.*lbf)




Hide 16604 3.INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY

a.

Install the No. 2 idler pulley sub-assembly with the bolt.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)


Hide 16031 5.INSTALL WATER INLET WITH THERMOSTAT SUB-ASSEMBLY