32971
1.INSTALL TRANSMISSION OIL THERMOSTAT
Install the transmission oil thermostat to the oil cooler stay with the bolt.
Connect the No. 2 transmission oil cooler hose and outlet No. 2 oil cooler hose to the transmission oil thermostat with each paint mark facing up and slide the 2 clips to secure them.
| *1 | No. 2 Transmission Oil Cooler Hose | *2 | Outlet No. 2 Oil Cooler Hose |
| *a | 0 to 3 mm (0 to 0.118 in.) | *b | 2 to 7 mm (0.0787 to 0.276 in.) |
| *c | Paint Mark | *d | 30° (Paint Mark Location) |
| *e | 45° (Claw of Clip Location) | - | - |
Make sure to slide the No. 2 transmission oil cooler hose and outlet No. 2 oil cooler hose until each contacts the hose stopper of the transmission oil thermostat.
Make sure that each paint mark and the claws of each clip are within the location shown in the illustration.
Install the No. 1 transmission oil cooler hose and outlet No. 1 oil cooler hose to the transmission oil thermostat with each paint mark facing the front of the vehicle and slide the 2 clips to secure them.
| *1 | No. 1 Transmission Oil Cooler Hose | *2 | Outlet No. 1 Oil Cooler Hose |
| *a | 0 to 3 mm (0 to 0.118 in.) | *b | 2 to 7 mm (0.0787 to 0.276 in.) |
| *c | Paint Mark | *d | 30° (Paint Mark Location) |
| *e | 45° (Claw of Clip Location) | - | - |
Make sure to slide the No. 1 transmission oil cooler hose and outlet No. 1 oil cooler hose until each contacts the hose stopper of the transmission oil thermostat.
Make sure that each paint mark is within the location shown in the illustration.
Make sure that the claws of the clip of the No. 1 transmission oil cooler hose are within the location shown in the illustration.
| *a | Pin |
| *b | Shaft |
When replacing the transmission oil thermostat with a new one:
Remove the pin from the transmission oil thermostat.
Make sure that the shaft of the transmission oil thermostat protrudes from the cap after the pin is removed.
33493A
2.INSTALL TRANSMISSION OIL COOLER
Engage the hook and temporarily install the transmission oil cooler to the automatic transaxle case sub-assembly with the bolt (A).
Install the bolt (B).
Install the bolt (C).
Fully tighten the bolt (A) to install the transmission oil cooler.
32907C
3.INSTALL NO. 1 OIL COOLER TUBE SUB-ASSEMBLY WITHOUT HOSE
Install the inlet No. 1 oil cooler hose, inlet No. 2 oil cooler hose and outlet No. 3 oil cooler hose to the No. 1 oil cooler tube sub-assembly without hose and slide the 3 clips to secure them.
| *1 | No. 1 Oil Cooler Tube Sub-assembly without Hose | *2 | Inlet No. 1 Oil Cooler Hose |
| *3 | Inlet No. 2 Oil Cooler Hose | *4 | Outlet No. 3 Oil Cooler Hose |
| *a | 2 to 7 mm (0.0787 to 0.276 in.) | *b | Paint Mark |
| *c | 45° (Claw of Clip Location) | - | - |
Make sure to slide the inlet No. 1 oil cooler hose, inlet No. 2 oil cooler hose and outlet No. 3 oil cooler hose until each contacts the hose stopper of the No. 1 oil cooler tube sub-assembly without hose.
Make sure to align the paint mark of each hose with the paint mark of each tube.
Make sure that the claws of each clip are within the location shown in the illustration.
| *a | 0 to 3 mm (0 to 0.118 in.) |
| *b | 2 to 7 mm (0.0787 to 0.276 in.) |
| *c | Paint Mark (Left Side of Vehicle) |
| *d | 30° (Paint Mark Location) |
| *e | 45° (Claw of Clip Location) |
Install the No. 1 oil cooler tube sub-assembly without hose to the automatic transaxle case sub-assembly and engine mounting bracket LH with the 2 bolts.
Connect the inlet No. 1 oil cooler hose to the connector tube and slide the clip to secure it.
Make sure to slide the inlet No. 1 oil cooler hose until it contacts the hose stopper of the connector tube.
Make sure that the paint mark of the inlet No. 1 oil cooler hose and claws of the clip are within the location shown in the illustration.
32943
4.CONNECT NO. 1 TRANSMISSION OIL COOLER HOSE
| *a | 0 to 3 mm (0 to 0.118 in.) |
| *b | 2 to 7 mm (0.0787 to 0.276 in.) |
| *c | Paint Mark (Left Side of Vehicle) |
| *d | 30° (Paint Mark Location) |
| *e | 45° (Claw of Clip Location) |
Connect the No. 1 transmission oil cooler hose to the oil cooler union sub-assembly and slide the clip to secure it.
Make sure to slide the No. 1 transmission oil cooler hose until it contacts the hose stopper of the oil cooler union sub-assembly.
Make sure that the paint mark of the No. 1 transmission oil cooler hose and claws of the clip are within the location shown in the illustration.
32942
5.CONNECT OUTLET NO. 1 OIL COOLER HOSE
| *a | Paint Mark |
| *b | 45° (Claw of Clip Location) |
Connect the outlet No. 1 oil cooler hose to the No. 1 oil cooler tube sub-assembly without hose and slide the clip to secure it.
Make sure to slide the outlet No. 1 oil cooler hose until it contacts the hose stopper of the No. 1 oil cooler tube sub-assembly without hose.
Make sure to align the paint mark of the outlet No. 1 oil cooler hose with the paint mark of the No. 1 oil cooler tube sub-assembly without hose.
Make sure that the claws of the clip are within the location shown in the illustration.
Install the transmission oil cooler tube clamp.
6.CONNECT OUTLET NO. 3 OIL COOLER HOSE
| *a | 0 to 3 mm (0 to 0.118 in.) |
| *b | 2 to 7 mm (0.0787 to 0.276 in.) |
| *c | Paint Mark |
| *d | 45° (Claw of Clip Location) |
Connect the outlet No. 3 oil cooler hose to the transmission oil cooler and slide the clip to secure it.
Make sure to slide the outlet No. 3 oil cooler hose until it contacts the hose stopper of the transmission oil cooler.
Make sure to align the paint mark of the outlet No. 3 oil cooler hose with paint mark of the transmission oil cooler.
Make sure that the claws of the clip are within the location shown in the illustration.
7.CONNECT INLET NO. 2 OIL COOLER HOSE
| *a | 0 to 3 mm (0 to 0.118 in.) |
| *b | 2 to 7 mm (0.0787 to 0.276 in.) |
| *c | Paint Mark |
| *d | 45° (Claw of Clip Location) |
Connect the inlet No. 2 oil cooler hose to the transmission oil cooler and slide the clip to secure it.
Make sure to slide the inlet No. 2 oil cooler hose until it contacts the hose stopper of the transmission oil cooler.
Make sure to align the paint mark of the inlet No. 2 oil cooler hose with the paint mark of the transmission oil cooler.
Make sure that the claws of the clip are within the location shown in the illustration.
16267H
8.CONNECT NO. 3 WATER BY-PASS HOSE
Connect the No. 3 water by-pass hose to the transmission oil cooler and slide the clip to secure it.
| *a | 2 to 7 mm (0.0787 to 0.276 in.) | *b | Paint Mark |
| *c | 45° (Claw of Clip Location) | - | - |
Make sure to slide the No. 3 water by-pass hose until it contacts the hose stopper of the transmission oil cooler.
Make sure to align the paint mark of the No. 3 water by-pass hose with the paint mark of the transmission oil cooler.
Make sure that the claws of the clip are within the location shown in the illustration.
16281K
9.CONNECT NO. 4 WATER BY-PASS HOSE
Connect the No. 4 water by-pass hose to the transmission oil cooler and slide the clip to secure it.
| *a | 2 to 7 mm (0.0787 to 0.276 in.) | *b | Paint Mark |
| *c | 45° (Claw of Clip Location) | - | - |
Make sure to slide the No. 4 water by-pass hose until it contacts the hose stopper of the transmission oil cooler.
Make sure to align the paint mark of the No. 4 water by-pass hose with the paint mark of the transmission oil cooler.
Make sure that the claws of the clip are within the location shown in the illustration.
28800
10.INSTALL BATTERY
17700
11.INSTALL AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE
17750A
12.INSTALL INLET AIR CLEANER ASSEMBLY
53295E
13.INSTALL COOL AIR INTAKE DUCT SEAL
53298E
14.INSTALL RADIATOR SIDE SEAL RH
53299D
15.INSTALL RADIATOR SIDE DEFLECTOR SEAL LH
16.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
17.ADD ENGINE COOLANT
18.ADJUST AUTOMATIC TRANSAXLE FLUID
19.INSPECT FOR OIL LEAK
20.INSPECT FOR COOLANT LEAK
53737B
21.INSTALL FRONT FENDER APRON SEAL LH
51441
22.INSTALL NO. 1 ENGINE UNDER COVER
23.INSTALL FRONT WHEEL LH