Home › Engine / Hybrid System › 2GR-FKS (ENGINE MECHANICAL) › ENGINE ASSEMBLY › from 2016.11
RM3160E _51 Engine / Hybrid System _060157 2GR-FKS ENGINE MECHANICAL _0299121 ENGINE ASSEMBLY A

2GR-FKS ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repair" after replacing the engine assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 12380 1.TEMPORARILY INSTALL REAR ENGINE MOUNTING INSULATOR ASSEMBLY

HINT:

Perform this procedure only when replacement of the rear engine mounting insulator assembly is necessary.


a.

Temporarily install the rear engine mounting insulator with the 2 nuts.


Hide 12362 2.TEMPORARILY INSTALL ENGINE MOUNTING INSULATOR RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator RH is necessary.


a.

Temporarily install the engine mounting insulator RH with the 3 nuts.


Hide 12372A 3.TEMPORARILY INSTALL ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


a.

Temporarily install the engine mounting insulator LH with the 3 nuts.


Hide 12360 4.TEMPORARILY INSTALL FRONT ENGINE MOUNTING INSULATOR ASSEMBLY

HINT:

Perform this procedure only when replacement of the front engine mounting insulator assembly is necessary.


a.

Temporarily install the front engine mounting insulator assembly with the 3 nuts.


Hide 6.REMOVE ENGINE ASSEMBLY FROM ENGINE STAND

a.

Using an engine sling device and engine lift, secure the engine assembly.

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or No. 1 engine hanger and No. 2 engine hanger may be damaged or deformed if the angle is incorrect.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.




b.

Remove the engine assembly from the engine stand.


Hide 32101 7.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

Hide 12315A 8.INSTALL ENGINE MOUNTING BRACKET RH

a.

Install the engine mounting bracket RH to the cylinder block sub-assembly with the 3 bolts.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)


Hide 43410 11.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH (for AWD)

Hide 51100G 12.INSTALL FRONT FRAME ASSEMBLY

a.

Install the rear engine mounting insulator assembly with the 2 bolts.

Torque:
75 N*m (765 kgf*cm, 55 ft.*lbf)


b.

Install the engine mounting insulator RH with the nut.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


c.

Install the engine mounting insulator LH with the nut.

Torque:
95 N*m (969 kgf*cm, 70 ft.*lbf)


d.

Install the front engine mounting insulator assembly with the bolt.

Torque:
87 N*m (887 kgf*cm, 64 ft.*lbf)


e.

Fully tighten the 11 temporarily installed nuts of the engine mounting insulators.

HINT:

Perform this procedure only when replacement of the engine mounting insulators is necessary.


A315943C01
1.615,0.365 1.927,0.521 0.313,0.156 10 false *1 1.74,3.146 2.052,3.302 0.313,0.156 10 false *2 5.083,0.302 5.396,0.458 0.313,0.156 10 false *3 5.375,3.219 5.688,3.375 0.313,0.156 10 false *4 1.042,1.438 1.198,1.635 0.156,0.198 10 true A 1.833,3.979 1.99,4.156 0.156,0.177 10 true B 0.604,1.771 0.76,1.969 0.156,0.198 10 true A 2.063,1.802 2.219,2 0.156,0.198 10 true A 5.802,4.573 5.958,4.771 0.156,0.198 10 true A 4.896,4.552 5.052,4.75 0.156,0.198 10 true A 4.948,1 5.104,1.198 0.156,0.198 10 true B 5.49,1.021 5.646,1.219 0.156,0.198 10 true B 5.729,1.885 5.885,2.063 0.156,0.177 10 true B 1.531,3.656 1.688,3.833 0.156,0.177 10 true B 2.104,3.5 2.26,3.677 0.156,0.177 10 true B
*1 Front Engine Mounting Insulator Assembly *2 Engine Mounting Insulator RH
*3 Engine Mounting Insulator LH *4 Rear Engine Mounting Insulator


Torque:
Nut (A) : 58 N*m (591 kgf*cm, 43 ft.*lbf)

Torque:
Nut (B) : 99 N*m (1010 kgf*cm, 73 ft.*lbf)


f.

Install the 7 hole plugs to the front frame assembly.

HINT:

Perform this procedure only when replacement of the engine mounting insulators is necessary.



Hide 48829A 15.INSTALL FRONT NO. 1 STABILIZER BRACKET LH (for AWD)

Hide 48824A 16.INSTALL FRONT NO. 1 STABILIZER BRACKET RH (for AWD)

HINT:

Perform the same procedure as for the LH side.


Hide 82121 17.INSTALL ENGINE WIRE

a.

Install the engine wire to the engine assembly with transaxle.


Hide 18.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

a.

Set the engine assembly with transaxle on the engine lifter.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, place the engine assembly with transaxle horizontally.

·

Do not place any height adjustment attachments or plate lift attachments under the front frame assembly.

·

Servicing an engine assembly while it is hanging is dangerous. This can be done only when installing/removing the engine assembly to/from an engine stand.

·

To prevent the oil pan from deforming, do not place any attachments under the oil pan of the engine assembly with transaxle.





c.

Install the engine assembly with transaxle to the vehicle body.

NOTICE:
·

Do not raise the engine assembly with transaxle more than necessary. If the engine assembly with transaxle is raised excessively, the vehicle may also be lifted up.

·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While raising the engine assembly with transaxle into the vehicle, do not allow it to contact the vehicle.




d.
A392602C02
0.24,0.969 0.396,1.167 0.156,0.198 10 true A 1.49,0.833 1.646,1.031 0.156,0.198 10 true A 1.781,0.833 1.938,1.031 0.156,0.198 10 true A 3.031,0.958 3.188,1.156 0.156,0.198 10 true A 0.448,0.302 0.604,0.5 0.156,0.198 10 true B 1.094,0.063 1.25,0.26 0.156,0.198 10 true B 2.24,0.063 2.396,0.26 0.156,0.198 10 true B 2.813,0.292 2.969,0.49 0.156,0.198 10 true B 1.833,2.438 1.99,2.635 0.156,0.198 10 true B 1.448,2.438 1.604,2.635 0.156,0.198 10 true B 0.573,2.427 0.729,2.625 0.156,0.198 10 true C 2.719,2.427 2.875,2.625 0.156,0.198 10 true C 2.74,2.948 2.896,3.146 0.156,0.198 10 true D 2.25,3.24 2.406,3.427 0.156,0.188 10 true D 1.094,3.24 1.25,3.427 0.156,0.188 10 true D 0.531,2.969 0.688,3.156 0.156,0.188 10 true D
V100135

Bolt
V100136

Nut


Install the frame side rail plate RH and frame side rail plate LH to the front frame assembly and vehicle body with the 6 bolts and 2 nuts.

Torque:
Bolt (A) : 85 N*m (867 kgf*cm, 63 ft.*lbf)
Bolt (B) and Nut (A) : 32 N*m (326 kgf*cm, 24 ft.*lbf)


e.

Install the front suspension member rear brace RH and front suspension member rear brace LH to the front frame assembly and vehicle body with the 6 bolts and 2 nuts.

Torque:
Bolt (C) : 85 N*m (867 kgf*cm, 63 ft.*lbf)
Bolt (D) and Nut (B) : 32 N*m (326 kgf*cm, 24 ft.*lbf)

HINT:

Perform "Inspection After Repair" after replacing the engine assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Hide 32101A 19.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT (for 2WD)

Hide 32101A 20.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT (for AWD)

Hide 11361J 21.INSTALL FLYWHEEL HOUSING UNDER COVER

a.

Install the flywheel housing under cover with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 43420G 22.INSTALL FRONT DRIVE SHAFT HOLE SNAP RING (for LH Side)

Hide 43410 23.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH (for 2WD)

Hide 48069 25.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 26.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48810 27.INSTALL FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 28.CONNECT FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45460 30.CONNECT TIE ROD ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 89542 32.CONNECT FRONT SPEED SENSOR RH

HINT:

Perform the same procedure as for the LH side.


Hide 17571 35.INSTALL NO. 1 EXHAUST PIPE SUPPORT BRACKET

a.

Install the No. 1 exhaust pipe support bracket to the oil pan sub-assembly with the 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 17410 36.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 17403 37.INSTALL FRONT NO. 3 EXHAUST PIPE SUB-ASSEMBLY

Hide 37100 38.INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for AWD)

Hide 88704 39.CONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 88703 40.CONNECT DISCHARGE HOSE SUB-ASSEMBLY

Hide 33820B 42.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Engage the transmission control cable assembly to the No. 3 transmission control cable bracket.


b.

Install a new clip to the No. 1 transmission control cable bracket.


c.
C102659C02
2.229,1.135 2.76,1.135 true 2.198,0.938 0.438,1.635 0.438,1.635 1.063,0.99 true 2.125,0.625 0.75,0.177 0.75,0.177 1.198,0.635 true 0.563,0.063 0.844,0.313 0.281,0.25 10 false *a 0.271,1.625 0.583,1.885 0.313,0.26 10 false *b 2.771,1.052 3.031,1.313 0.26,0.26 10 false *c
*a Claw A
*b Claw B
*c Transmission Control Cable Assembly


Connect the transmission control cable assembly to the No. 1 transmission control cable bracket.

NOTICE:
·

Make sure that the claws A on the clip are securely fit into the No. 1 transmission control cable bracket holes.

·

Make sure that the transmission control cable assembly is securely installed inside of the claws B of the clip.




d.

Connect the transmission control cable assembly to the transmission control shaft lever with the clip.

NOTICE:

Before connecting the transmission control cable assembly, check that the park/neutral position switch assembly and the shift lever are in neutral.



Hide 82121 43.CONNECT ENGINE WIRE

a.

Engage the 2 claws to connect the engine room main wire to the engine wire.


b.

Install the engine room main wire with engine wire to the positive (+) battery terminal with the nut.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


c.

Engage the clamp and connect the engine wire.


d.

Connect the No. 3 earth wire with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


e.

Engage the 2 clamps.


f.
A392612

Push down the lock lever to connect the ECM connector.

NOTICE:
·

When connecting the ECM connector, make sure that dirt, water or other foreign matter do not contact the connecting part of the ECM connector.

·

Be sure to securely connect the ECM connector.




g.

Connect the 4 connectors to the engine room relay block assembly.


h.

Engage 2 claws to connect the engine wire.


i.

Engage the 2 clamps to connect the engine wire.


j.

Install the engine wire to the engine room relay block assembly with the nut.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


k.

Connect the earth wire with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


l.

Install the No. 1 relay block cover to the engine room relay block assembly.


Hide 28100 44.INSTALL STARTER ASSEMBLY

Hide 32971 45.CONNECT TRANSMISSION OIL THERMOSTAT

a.

Connect the transmission oil thermostat to the oil cooler stay with the bolt.

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)


Hide 32942 46.CONNECT OUTLET NO. 1 OIL COOLER HOSE

a.

Connect the outlet No. 1 oil cooler hose to the transmission oil thermostat and slide the clip to secure it.


Hide 32943 47.CONNECT NO. 1 TRANSMISSION OIL COOLER HOSE

a.

Connect the No. 1 transmission oil cooler hose to the transmission oil thermostat and slide the clip to secure it.


Hide 23901 48.CONNECT FUEL TUBE SUB-ASSEMBLY

a.

Connect the fuel tube sub-assembly (for Port Injection).

i.

Connect the fuel tube sub-assembly to the fuel pipe.

Click hereEngine / Hybrid System>2GR-FKS FUEL>FUEL SYSTEM>PRECAUTION



b.

Connect the No. 2 fuel tube sub-assembly (for Direct Injection).

i.

Connect the No. 2 fuel tube sub-assembly to the fuel pipe.

Click hereEngine / Hybrid System>2GR-FKS FUEL>FUEL SYSTEM>PRECAUTION



c.

Install the No. 1 fuel pipe clamp to the fuel tube connector.


d.

Fuel Pipe Clamp Type A:

Install the No. 2 fuel pipe clamp to the No. 1 fuel pipe clamp.


e.
A412603C01
0.833,2.042 1.354,2.042 1.354,2.042 1.354,1.854 false 1.125,2.042 1.125,1.771 false 2.646,1.792 2.052,1.792 2.052,1.792 2.052,1.438 true 2.26,1.792 2.26,1.583 true 0.667,1.948 0.979,2.104 0.313,0.156 10 false *a 2.677,1.708 2.99,1.865 0.313,0.156 10 false *b
*a Protrusion
*b Notch


Fuel Pipe Clamp Type B:

Align the protrusions of the No. 2 fuel pipe clamp with the notches of the No. 1 fuel pipe clamp, and engage the 2 claws to install the No. 2 fuel pipe clamp.


Hide 16281K 49.CONNECT NO. 4 WATER BY-PASS HOSE

a.

Connect the No. 4 water by-pass hose to the radiator pipe assembly and slide the clip to secure it.


Hide 16267H 50.CONNECT NO. 3 WATER BY-PASS HOSE

a.

Connect the No. 3 water by-pass hose to the radiator pipe assembly and slide the clip to secure it.


Hide 87209 51.CONNECT WATER HOSE SUB-ASSEMBLY

a.

Engage the clamp to the water hose sub-assembly.


b.

Connect the 2 water hose sub-assemblies and slide the 2 clips to secure them.


Hide 16572D 52.CONNECT NO. 2 RADIATOR HOSE

a.

Connect the No. 2 radiator hose to the water inlet and slide the clip to secure it.


Hide 16571C 53.CONNECT NO. 1 RADIATOR HOSE

a.

Connect the No. 1 radiator hose to the radiator pipe clamp.


b.

Connect the No. 1 radiator hose to the water outlet and slide the clip to secure it.


Hide 44773F 54.CONNECT UNION TO CHECK VALVE HOSE

a.

for LHD

i.

Engage the clamp to the union to check valve hose.



b.

Connect the union to check valve hose to the intake air surge tank assembly and slide the clip to secure it.


Hide 23826 55.CONNECT NO. 1 FUEL VAPOR FEED HOSE

a.

Connect the No. 1 fuel vapor feed hose to the No. 1 vacuum switching valve and slide the clip to secure it.


b.

Connect the purge VSV (purge valve) connector.


Hide 12363A 56.INSTALL ENGINE MOVING CONTROL ROD

HINT:

Perform this procedure only when replacement of the engine moving control rod or No. 3 engine mounting stay RH is necessary.


a.
A315766C01
0.677,0.833 1.292,1.219 false 2.563,0.635 2.563,1.021 false 2.125,1.354 2.125,1.74 false 2.51,1.073 2.823,1.229 0.313,0.156 10 false *1 0.51,0.74 0.823,0.896 0.313,0.156 10 false *2 2.073,1.781 2.385,1.938 0.313,0.156 10 false *3 0.948,1.25 1.104,1.448 0.156,0.198 10 false A
*1 Engine Moving Control Rod
*2 No. 3 Engine Mounting Stay RH
*3 Engine Moving Control Rod Bracket


Temporarily install the No. 3 engine mounting stay RH and engine moving control rod to the engine moving control rod bracket with the 2 bolts.


b.

Tighten the bolt (A).

Torque:
78 N*m (795 kgf*cm, 58 ft.*lbf)


Hide 12313 57.INSTALL ENGINE MOVING CONTROL ROD BRACKET

a.
A396419N01
0.438,0.156 0.594,0.354 0.156,0.198 10 true A 1.813,0.417 1.969,0.615 0.156,0.198 10 true C 2.438,1.135 2.594,1.333 0.156,0.198 10 true D 2.646,1.406 2.802,1.604 0.156,0.198 10 true B 0.948,1.542 1.104,1.74 0.156,0.198 10 true E

When replacing the engine moving control rod.

i.

Install the engine moving control rod bracket with engine moving control rod with the 4 bolts.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)

NOTICE:

Temporarily tighten the bolt (A) and (B), and then fully tighten the 4 bolts in the order of (C), (D), (A) and (B).



ii.

Tighten the bolt (E).

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)



b.
A392600N02
0.458,0.042 0.615,0.24 0.156,0.198 10 true A 3.052,1.583 3.208,1.781 0.156,0.198 10 true B 2.052,0.375 2.208,0.573 0.156,0.198 10 true C 2.75,1.104 2.906,1.302 0.156,0.198 10 true D

When not replacing the engine moving control rod.

i.

Install the engine moving control rod bracket with engine moving control rod with the 4 bolts.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)

NOTICE:

Temporarily tighten the bolt (A) and (B), and then fully tighten the 4 bolts in the order of (C), (D), (A) and (B).




Hide 12327A 58.INSTALL NO. 2 ENGINE MOUNTING STAY RH

a.

Install the No. 2 engine mounting stay RH to the engine mounting insulator sub-assembly RH with the bolt and 2 nuts.

Torque:
Bolt : 38 N*m (387 kgf*cm, 28 ft.*lbf)
Nut : 23 N*m (235 kgf*cm, 17 ft.*lbf)


Hide 17119A 59.INSTALL AIR CLEANER BRACKET

a.

Install the air cleaner bracket to the vehicle body with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Engage the clamp.


Hide 47233 60.INSTALL RESERVOIR BRACKET (for LHD)

Hide 47220D 61.INSTALL BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (for LHD)

Hide 47233 62.INSTALL RESERVOIR BRACKET (for RHD)

Hide 47220D 63.INSTALL BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (for RHD)

Hide 17700 64.INSTALL AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE

a.
A394302C01
0.375,2.354 0.542,2 0.542,2 0.729,2 true 0.844,2.677 1,2.677 1,2.677 1.104,2.208 true 1.969,2.063 2.104,2.063 2.104,2.063 2.156,2.271 false 2.865,2.156 2.688,2.323 2.688,2.323 2.688,2.417 true 3.063,2.281 3.208,2.51 3.208,2.51 3.208,2.75 true 0.667,2.583 0.979,2.74 0.313,0.156 10 false *a 0.76,1.906 1.073,2.063 0.313,0.156 10 false *b 3.146,2.75 3.354,3.042 0.208,0.292 10 false *c 2.365,1.615 2.698,1.969 0.333,0.354 10 false *d 2.625,2.406 2.938,2.563 0.313,0.156 10 false *e 1.813,1.979 2.125,2.135 0.313,0.156 10 false *f 2.917,1.625 3.25,1.948 0.333,0.323 10 false *g
*a Cutout
*b Protrusion
*c Hose Clamp
*d Up
*e Stopper
*f Air Cleaner Hose Assembly
*g 5.0 to 9.0 mm (0.197 to 0.354 in.)


Install the air cleaner assembly with air cleaner hose to the throttle body with motor assembly.

NOTICE:

Align the cutout of the air cleaner hose assembly with the protrusion of the throttle body with motor assembly.



b.

Tighten the hose clamp in the position shown in the illustration.

HINT:

Make sure that the hose clamp is positioned as shown in the illustration.



c.

Install the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


d.

Connect the No. 2 ventilation hose to the air cleaner hose assembly and slide the clip to secure it.


e.

Engage the No. 1 fuel vapor feed hose to the air cleaner hose assembly.


f.

Engage the wire harness clamp.


g.

Connect the mass air flow meter sub-assembly connector.


Hide 17750A 65.INSTALL INLET AIR CLEANER ASSEMBLY

a.

Install the inlet air cleaner assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 28800 66.INSTALL BATTERY

a.

Install the battery and battery tray.


b.

Install the battery clamp and battery clamp bolt with the bolt and nut.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


c.

Connect the cable to the positive (+) battery terminal.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


Hide 67.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

a.

Connect the cable to the negative (-) battery terminal.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



Hide 68.INSTALL FRONT WHEELS

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 73.ADD TRANSFER OIL (for AWD)

Hide 74.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 78.INSPECT ENGINE COOLANT LEVEL IN RESERVOIR TANK

Hide 81.INSPECT FOR OIL LEAK

Hide 82.INSPECT FOR EXHAUST GAS LEAK

Hide 91.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 11209 92.INSTALL V-BANK COVER SUB-ASSEMBLY

a.
A392581N01
0.583,1.083 0.74,1.281 0.156,0.198 10 true 1 1.896,1.771 2.052,1.969 0.156,0.198 10 true 1 1.479,0.75 1.635,0.948 0.156,0.198 10 true 2 2.323,1.042 2.479,1.24 0.156,0.198 10 true 2

Engage the 4 clips in the order shown in the illustration to install the V-bank cover sub-assembly.

NOTICE:
·

Securely engage the clips.

·

If the clips are forcibly engaged or struck with an object, they may be damaged.




Hide 53295E 93.INSTALL COOL AIR INTAKE DUCT SEAL

Hide 53298E 94.INSTALL RADIATOR SIDE SEAL RH

Hide 53299D 95.INSTALL RADIATOR SIDE DEFLECTOR SEAL LH

Hide 55701J 96.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 97.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 53737B 98.INSTALL FRONT FENDER APRON SEAL LH

a.

Install the front fender apron seal LH with the 2 bolts and clip.


Hide 53736 99.INSTALL FRONT FENDER APRON SEAL RH

a.

Install the front fender apron seal RH with the 2 bolts and clip.


Hide 53876A 100.INSTALL FRONT FENDER LINER LH

a.

Install the front fender liner LH with the 3 screws and 3 clips.


Hide 53875A 101.INSTALL FRONT FENDER LINER RH

a.

Install the front fender liner RH with the 3 screws and 3 clips.


Hide 51442 103.INSTALL NO. 2 ENGINE UNDER COVER

a.

Install the No. 2 engine under cover with the 2 bolts, 2 screws and clip.


Hide 51441 104.INSTALL NO. 1 ENGINE UNDER COVER

a.

Install the No. 1 engine under cover with the 8 bolts, 6 screws and 3 clips.