The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.
This DTC is stored when a microphone connection detection signal line is disconnected.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1579 | Voice Recognition Microphone Disconnected | Microphone signal is lost | ·
Map light assembly (telephone microphone assembly) ·
Radio and display receiver assembly ·
Harness or connector ·
Telematics transceiver* |
*: w/ Manual (SOS) Switch
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F71-19 (MIN-) - Body ground | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (w/o Manual (SOS) Switch) | A |
| OK (w/ Manual (SOS) Switch) | B |
| NG | C |
A
B
C
Disconnect the F71 radio and display receiver assembly connector.
Disconnect the S1 map light assembly (telephone microphone assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F71-6 (SNS2) - S1-13 (SNS2) | Always | Below 1 Ω |
| F71-19 (MIN-) - S1-4 (MCO-) | Always | Below 1 Ω |
| F71-6 (SNS2) or S1-13 (SNS2) - Body ground | Always | 10 kΩ or higher |
| F71-19 (MIN-) or S1-4 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the map light assembly (telephone microphone assembly).
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
| *a | Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 13 (SNS2) - 4 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F140 Telematics transceiver connector.
Disconnect the S1 map light assembly (telephone microphone assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F140-35 (MCI-) - S1-4 (MCO-) | Always | Below 1 Ω |
| F140-35 (MCI-) or S1-4 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F71 radio and display receiver assembly connector.
Disconnect the F140 Telematics transceiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F71-19 (MIN-) - F140-19 (MCO-) | Always | Below 1 Ω |
| F71-19 (MIN-) or F140-19 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F71 radio and display receiver assembly connector.
Disconnect the S1 map light assembly (telephone microphone assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F71-6 (SNS2) - S1-13 (SNS2) | Always | Below 1 Ω |
| F71-6 (SNS2) or S1-13 (SNS2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the F140 telematics transceiver connector.
Reconnect the F71 radio and display receiver assembly connector.
| *a | Component with harness connected
(Telematics Transceiver) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F140-35 (MCI-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the map light assembly (telephone microphone assembly).
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
| *a | Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 13 (SNS2) - 4 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG