This DTC is stored when a malfunction occurs in the speakers.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15C3 | Speaker Output Short | A short is detected in the speaker output circuit | ·
Harness or connector ·
Speaker ·
Radio and display receiver assembly ·
Telematics transceiver* |
*: w/ Manual (SOS) Switch
for 6 Speakers
for 12 Speakers
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for 6 Speakers | A |
| for 12 Speakers | B |
A
B
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/ Manual (SOS) Switch | A |
| w/o Manual (SOS) Switch | B |
A
B
Disconnect the F69 and F70 radio and display receiver assembly connectors.
Disconnect the F140 telematics transceiver assembly connector.
Disconnect the G5 front No. 2 speaker assembly LH connector.
Disconnect the K4 and J4 rear speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F69-1 (FR+) or F140-2 (SPI+) - Body ground | Always | 10 kΩ or higher |
| F69-5 (FR-) or F140-3 (SPI-) - Body ground | Always | 10 kΩ or higher |
| F69-2 (FL+) or G5-4 (+) - Body ground | Always | 10 kΩ or higher |
| F69-6 (FL-) or G5-2 (-) - Body ground | Always | 10 kΩ or higher |
| F70-1 (RR+) or J4-1 - Body ground | Always | 10 kΩ or higher |
| F70-3 (RR-) or J4-2 - Body ground | Always | 10 kΩ or higher |
| F70-2 (RL+) or K4-1 - Body ground | Always | 10 kΩ or higher |
| F70-6 (RL-) or K4-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F140 telematics transceiver connector.
Disconnect the G1 front No. 2 speaker assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F140-5 (SPO+) or G1-4 (+) - Body ground | Always | 10 kΩ or higher |
| F140-6 (SPO-) or G1-2 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H3 and I3 front No. 1 speaker assembly connectors.
Disconnect the G1 and G5 front No. 2 speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G1-3 (+) or H3-1 - Body ground | Always | 10 kΩ or higher |
| G1-1 (-) or H3-2 - Body ground | Always | 10 kΩ or higher |
| G5-3 (+) or I3-1 - Body ground | Always | 10 kΩ or higher |
| G5-1 (-) or I3-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Inspect the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
Inspect the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION
Clear the DTCs.
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL
Inspect the rear speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the telematics transceiver.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| *a | Component without harness connected
(Telematics Transceiver) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (SPI+) - 5 (SPO+) | Always | Below 1 Ω |
| 3 (SPI-) - 6 (SPO-) | Always | Below 1 Ω |
| 2 (SPI+) - 3 (SPI-) | Always | 10 kΩ or higher |
| 5 (SPO+) - 6 (SPO-) | Always | 10 kΩ or higher |
| 2 (SPI+) or 5 (SPO+) - Body ground | Always | 10 kΩ or higher |
| 3 (SPI-) or 6 (SPO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F69 and F70 radio and display receiver assembly connectors.
Disconnect the G1 and G5 front No. 2 speaker assembly connectors.
Disconnect the K4 and J4 rear speaker assembly connectors.
Measure the resistance between the radio and display receiver assembly and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F69-1 (FR+) or G1-4 (+) - Body ground | Always | 10 kΩ or higher |
| F69-5 (FR-) or G1-2 (-) - Body ground | Always | 10 kΩ or higher |
| F69-2 (FL+) or G5-4 (+) - Body ground | Always | 10 kΩ or higher |
| F69-6 (FL-) or G5-2 (-) - Body ground | Always | 10 kΩ or higher |
| F70-1 (RR+) or J4-1 - Body ground | Always | 10 kΩ or higher |
| F70-3 (RR-) or J4-2 - Body ground | Always | 10 kΩ or higher |
| F70-2 (RL+) or K4-1 - Body ground | Always | 10 kΩ or higher |
| F70-6 (RL-) or K4-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H3 and I3 front No. 1 speaker assembly connectors.
Disconnect the G1 and G5 front No. 2 speaker assembly connectors.
Measure the resistance between each of the front No. 2 speaker assemblies and body ground to check for a short circuit in the wire harness.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G1-3 (+) or H3-1 - Body ground | Always | 10 kΩ or higher |
| G1-1 (-) or H3-2 - Body ground | Always | 10 kΩ or higher |
| G5-3 (+) or I3-1 - Body ground | Always | 10 kΩ or higher |
| G5-1 (-) or I3-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Inspect the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
Inspect the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION
Clear the DTCs.
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL
Inspect the rear speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F75 stereo component amplifier assembly connector.
Disconnect the F140 telematics transceiver connector.
Disconnect the H3 and I3 front No. 1 speaker assembly connector.
Disconnect the G3 front No. 3 speaker assembly connector.
Disconnect the J4 and K4 rear speaker assembly connectors.
Disconnect the X23 and X5 rear No. 3 speaker assembly connectors.
Disconnect the G2 and G6 front No. 2 speaker assembly connectors.
Disconnect the X26 rear No. 2 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F75-15 (FR+) or H3-1 - Body ground | Always | 10 kΩ or higher |
| F75-30 (FR-) or H3-2 - Body ground | Always | 10 kΩ or higher |
| F75-11 (FL+) or I3-1 - Body ground | Always | 10 kΩ or higher |
| F75-26 (FL-) or I3-2 - Body ground | Always | 10 kΩ or higher |
| F75-10 (CTR+) or G3-2 - Body ground | Always | 10 kΩ or higher |
| F75-25 (CTR-) or G3-1 - Body ground | Always | 10 kΩ or higher |
| F75-12 (RR+) or J4-1 - Body ground | Always | 10 kΩ or higher |
| F75-27 (RR-) or J4-2 - Body ground | Always | 10 kΩ or higher |
| F75-4 (RL+) or K4-1 - Body ground | Always | 10 kΩ or higher |
| F75-19 (RL-) or K4-2 - Body ground | Always | 10 kΩ or higher |
| F75-9 (SR+) or X23-2 - Body ground | Always | 10 kΩ or higher |
| F75-24 (SR-) or X23-1 - Body ground | Always | 10 kΩ or higher |
| F75-5 (SL+) or X5-2 - Body ground | Always | 10 kΩ or higher |
| F75-20 (SL-) or X5-1 - Body ground | Always | 10 kΩ or higher |
| F75-14 (TWR+) or F140-2 (SPI+) - Body ground | Always | 10 kΩ or higher |
| F75-29 (TWR-) or F140-3 (SPI-) - Body ground | Always | 10 kΩ or higher |
| F75-13 (TWL+) or G6-4 (TWL+) - Body ground | Always | 10 kΩ or higher |
| F75-28 (TWL-) or G6-3 (TWL-) - Body ground | Always | 10 kΩ or higher |
| F75-8 (WF1+) or X26-4 (WF1+) - Body ground | Always | 10 kΩ or higher |
| F75-23 (WF1-) or X26-3 (WF1-) - Body ground | Always | 10 kΩ or higher |
| F75-7 (WF2+) or X26-2 (WF2+) - Body ground | Always | 10 kΩ or higher |
| F75-22 (WF2-) or X26-1 (WF2-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F140 telematics transceiver connector.
Disconnect the G2 front No. 2 speaker assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F140-5 (SPO+) or G2-4 (TWR+) - Body ground | Always | 10 kΩ or higher |
| F140-6 (SPO-) or G2-3 (TWR-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the telematics transceiver.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| *a | Component without harness connected
(Telematics Transceiver) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2 (SPI+) - 5 (SPO+) | Always | Below 1 Ω |
| 3 (SPI-) - 6 (SPO-) | Always | Below 1 Ω |
| 2 (SPI+) - 3 (SPI-) | Always | 10 kΩ or higher |
| 5 (SPO+) - 6 (SPO-) | Always | 10 kΩ or higher |
| 2 (SPI+) or 5 (SPO+) - Body ground | Always | 10 kΩ or higher |
| 3 (SPI-) or 6 (SPO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Click here
Inspect the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 3 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
Inspect the front No. 3 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL
Inspect the rear speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear No. 3 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>BACK DOOR SPEAKER>REMOVAL
Inspect the rear No. 3 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>BACK DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
Inspect the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION
Clear the DTCs.
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>BACK DOOR SPEAKER>REMOVAL
Inspect the rear NO.2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>BACK DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG