Home › Drivetrain › UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › 2016.11–2017.10
RM3160E _52 Drivetrain _060164 UA80E AUTOMATIC TRANSMISSION / TRANSAXLE _0298261 AUTOMATIC TRANSAXLE SYSTEM C

UA80E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P071512  Input/Turbine Speed Sensor "A" Circuit Short to Battery  P071514  Input/Turbine Speed Sensor "A" Circuit Short to Ground or Open  P071531  Input/Turbine Speed Sensor "A" No Signal  


DESCRIPTION

The transmission revolution sensor (NT) detects the input shaft rotation speed and sends it to the ECM.

Based on the transmission revolution sensor (NT) signal and the transmission revolution sensor (NC) signals, the ECM controls engine torque and shift timing. Based on the input shaft rotation speed and the engine speed signal, lock-up control is performed.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P071512 Input/Turbine Speed Sensor "A" Circuit Short to Battery 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

The battery voltage is 8 V or more, the ignition switch is ON and the starter is off.

2.

Transmission revolution sensor (NT) input voltage is more than 1.9 V

3.

4.5 seconds

4.

1-trip detection logic


·

Transmission revolution sensor (NT)

·

Transmission wire

·

Harness and connector

·

ECM


Comes on DTC stored SAE Code:
P07C0
P071514 Input/Turbine Speed Sensor "A" Circuit Short to Ground or Open 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

The battery voltage is 8 V or more, the ignition switch is ON and the starter is off.

2.

Transmission revolution sensor (NT) input voltage is less than 0.1 V

3.

4.5 seconds

4.

1-trip detection logic


·

Transmission revolution sensor (NT)

·

Transmission wire

·

Harness and connector

·

ECM


Comes on DTC stored SAE Code:
P07BF
P071531 Input/Turbine Speed Sensor "A" No Signal 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

All of the following conditions are met:

(a)

The battery voltage is 8 V or more.

(b)

Park/neutral position switch D input signal is ON

(c)

Speed indicated by transmission revolution sensor (NC) is 520 rpm or more

(d)

The vehicle speed is 23 km/h (14 mph) or more.

(e)

Vehicle being driven in 1st, 2nd, 3rd, 4th, 5th, 6th, 7th or 8th gear


2.

Speed indicated by transmission revolution sensor (NT) is less than 300 rpm

3.

5 seconds

4.

1-trip detection logic


·

Transmission revolution sensor (NT)

·

Transmission wire

·

Harness and connector

·

ECM


Comes on DTC stored SAE Code:
P0717

MONITOR DESCRIPTION

The NT terminal of the ECM detects a pulse signal from the transmission revolution sensor (NT) (input RPM). The ECM calculates gear shifts by comparing input signals of the transmission revolution sensor (NT) with the transmission revolution sensor (NC).

While the vehicle is being driven in 1st, 2nd, 3rd, 4th, 5th, 6th, 7th or 8th gear with the shift lever in D, if the input shaft revolution (speed) is less than 300 rpm*1 when the vehicle speed is 23 km/h (14.29 mph) or more, the ECM interprets this as a malfunction, illuminates the MIL and stores a DTC.

*: Pulse is not output or is irregularly output.

WIRING DIAGRAM

C367619E01
1,1.729 2.563,2.219 1.563,0.49 10 false Transmission Revolution Sensor (NT) 1.219,3.021 2.781,3.51 1.563,0.49 10 false Transmission Wire 5.469,3.167 5.927,3.365 0.458,0.198 10 false C1 5.458,3.313 5.917,3.51 0.458,0.198 10 false ECM 5.135,2.271 5.594,2.469 0.458,0.198 10 false NTO 4.844,2.271 5.302,2.469 0.458,0.198 10 false 74 4.833,1.146 5.292,1.344 0.458,0.198 10 false 75 5.135,1.146 5.594,1.344 0.458,0.198 10 false NTB 5.708,0.854 6.167,1.052 0.458,0.198 10 false 12 V 2.729,1.146 3.188,1.344 0.458,0.198 10 false NTB 2.729,2.271 3.188,2.469 0.458,0.198 10 false NTO 3.146,2.281 3.604,2.479 0.458,0.198 10 false 11 3.135,1.146 3.594,1.344 0.458,0.198 10 false 12 0.625,1.396 1.083,1.594 0.458,0.198 10 false 1 0.635,2.219 1.094,2.417 0.458,0.198 10 false 2 1.219,2.875 1.677,3.073 0.458,0.198 10 false C62

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


HINT:

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.



DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Transmission / Data List / NT Sensor Speed.


g.

Read the Data List according to the display on the GTS.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
NT Sensor Speed Input shaft speed Min.: 0 rpm
Max.: 12750 rpm
·

Equal to engine speed: Lock-up on (after warming up engine)

·

Nearly equal to engine speed: Lock-up off (idling with shift lever in N)


Data is displayed in increments of 50 rpm
Powertrain > Transmission > Data List
Tester Display
NT Sensor Speed
50003 373 174
HINT:
·

NT Sensor Speed is always 0 while driving: Open or short in the sensor or circuit.

·

NT Sensor Speed is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more: Sensor malfunction, improper installation, or intermittent connection malfunction in the circuit.





PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Data List / NT Sensor Speed and NT Sensor Voltage.


e.

Read the Data List according to the display on the GTS.

Powertrain > Transmission > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
NT Sensor Speed Input shaft speed Min.: 0 rpm
Max.: 12750 rpm
·

Equal to engine speed: Lock-up on (after warming up engine)

·

Nearly equal to engine speed: Lock-up off (idling with shift lever in N)


Data is displayed in increments of 50 rpm
NT Sensor Voltage NT sensor voltage Min.: 0.000 V
Max.: 4.999 V
0.1 to 1.9 V: Engine idling -
Powertrain > Transmission > Data List
Tester Display
NT Sensor Speed
NT Sensor Voltage
50003 373 174,175

Result:
Result Proceed to
Data List values are normal A
Data List values are not normal B



A

5.REPLACE ECM

B

2.INSPECT TRANSMISSION REVOLUTION SENSOR (NT)
2.INSPECT TRANSMISSION REVOLUTION SENSOR (NT)
a.
C361134C04
1.469,0.146 1.906,0.417 0.438,0.271 1.281,1.156 0.667,1.75 true 1.385,1.156 2,1.75 true 1.563,0.198 2.021,0.396 0.458,0.198 10 false C62 1.917,1.781 2.375,1.979 0.458,0.198 10 false NTB 0.542,1.781 1,1.979 0.458,0.198 10 false NTO 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Transmission Wire)


Disconnect the C62 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C62-11 (NTO) - Body ground Always 99 to 101 Ω


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C62-12 (NTB) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT TRANSMISSION WIRE (TRANSMISSION REVOLUTION SENSOR (NT))

NG

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
3.INSPECT TRANSMISSION WIRE (TRANSMISSION REVOLUTION SENSOR (NT))
a.
C361135C05
1.698,1.385 1.333,1.917 true 1.885,1.385 2.333,1.917 true 2.125,3.625 2.5,4.25 true 2.021,3.594 1.667,4.25 true 0.604,0.583 0.917,0.781 0.313,0.198 10 false *a 0.604,2.667 0.917,2.865 0.313,0.198 10 false *b 1.271,1.99 1.427,2.188 0.156,0.198 10 false 1 2.292,1.979 2.448,2.177 0.156,0.198 10 false 2 2.417,4.281 2.875,4.479 0.458,0.198 10 false NTO 1.542,4.281 2,4.479 0.458,0.198 10 false NTB 0.083,0.083 0.396,0.281 0.313,0.198 10 false *1
*1 Transmission Wire
*a Transmission Revolution Sensor (NT) Side
*b Wire Harness Connector Side


Disconnect the transmission revolution sensor (NT) connector.

When Not Using the Engine Support Bridge: Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>TRANSMISSION WIRE(When Not Using the Engine Support Bridge)>REMOVAL

When Using the Engine Support Bridge: Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>TRANSMISSION WIRE(When Using the Engine Support Bridge)>REMOVAL


b.

Disconnect the C62 transmission wire connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance
Tester Connection Condition Specified Condition
1 (transmission revolution sensor (NT) side) - 12 (NTB) (wire harness connector side) Always Below 1 Ω
2 (transmission revolution sensor (NT) side) - 11 (NTO) (wire harness connector side) Always Below 1 Ω
1 (transmission revolution sensor (NT) side) or 12 (NTB) (wire harness connector side) - Body ground and other terminals Always 10 kΩ or higher
2 (transmission revolution sensor (NT) side) or 11 (NTO) (wire harness connector side) - Body ground and other terminals Always 10 kΩ or higher

Result:
Proceed to
OK
NG




OK

REPLACE TRANSMISSION REVOLUTION SENSOR (NT)

NG

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.

Disconnect the C62 transmission wire connector.


b.

Disconnect the C1 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C62-12 (NTB) - C1-75 (NTB) Always Below 1 Ω
C62-11 (NTO) - C1-74 (NTO) Always Below 1 Ω
C62-12 (NTB) or C1-75 (NTB) - Body ground and other terminals Always 10 kΩ or higher
C62-11 (NTO) or C1-74 (NTO) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT