Home › Drivetrain › UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › 2016.11–2017.10
RM3160E _52 Drivetrain _060164 UA80E AUTOMATIC TRANSMISSION / TRANSAXLE _0298261 AUTOMATIC TRANSAXLE SYSTEM C

UA80E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P074011  Torque Converter Clutch Circuit Short to Ground  


DESCRIPTION

Solenoid (SL) valve is turned on and off by signals from the ECM to control the hydraulic pressure acting on the lock-up relay valve, which then controls operation of the lock-up clutch.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P074011 Torque Converter Clutch Circuit Short to Ground 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

Solenoid (SL) valve is operated

2.

Solenoid (SL) valve circuit is short to ground

3.

Malfunction status occurs 1 time per trip

4.

2-trip detection logic


·

Solenoid (SL) valve

·

Transmission wire

·

Harness and connector

·

ECM


Comes on DTC stored SAE Code:
P2769

Fail-safe function:

If the ECM detects a malfunction, it turns Solenoid (SL) valve off.

MONITOR DESCRIPTION

Based on the signals from the throttle position sensor, the air flow meter and the crankshaft position sensor, the ECM sends a signal to solenoid (SL) valve to regulate the hydraulic pressure and provide smoother torque converter engagement. Solenoid (SL) valve responds to commands from the ECM. The valve controls the lock-up relay valve to perform the torque-converter lock-up function. If the ECM detects a short to ground in the solenoid (SL) valve circuit, it will illuminate the MIL and store the DTC.

WIRING DIAGRAM

C311454E90
1.49,1.719 5.01,1.917 3.521,0.198 10 false Solenoid (SL) Valve 1.531,2.625 5.052,2.823 3.521,0.198 10 false C62 1.521,2.792 5.042,2.99 3.521,0.198 10 false Transmission Wire 5.625,2.885 5.938,3.083 0.313,0.198 10 false C1 5.635,3.052 6.094,3.25 0.458,0.198 10 false ECM 3.302,1.125 3.615,1.323 0.313,0.198 10 false SL 5.177,1.125 5.49,1.323 0.313,0.198 10 false SL 3.625,1.125 3.938,1.323 0.313,0.198 10 false 13 4.896,1.125 5.208,1.323 0.313,0.198 10 false 62 5.771,0.823 6.25,1.042 0.479,0.219 10 false 12 V

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


HINT:

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Perform the D Position Shift Test inspection in Road Test.

Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>ROAD TEST

2.

Turn the ignition switch off.

3.

Perform step (1) again.



PROCEDURE

1.INSPECT TRANSMISSION WIRE (SOLENOID (SL) VALVE)
a.
C361126C02
2.146,1.042 2.5,0.25 true 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 2.552,0.177 2.865,0.375 0.313,0.198 10 false SL
*a Component without harness connected
(Transmission Wire)


Disconnect the C62 transmission wire connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
13 (SL) - Body ground 20°C (68°F) 11 to 15 Ω



c.

Connect the C62 transmission wire connector.


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

NG

4.INSPECT SOLENOID (SL) VALVE
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.

Disconnect the C1 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C1-62 (SL) - Body ground 20°C (68°F) 11 to 15 Ω



Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)

3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

4.INSPECT SOLENOID (SL) VALVE
a.
C361133C01
0.094,0.083 0.406,0.281 0.313,0.198 10 false *1 2.583,0.24 3.042,0.438 0.458,0.198 10 false (+) 1.594,0.26 2.052,0.458 0.458,0.198 10 false (-)
*1 Solenoid (SL) Valve


Remove the solenoid (SL) valve.

Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Solenoid (SL) valve connector terminal - Solenoid (SL) valve body 20°C (68°F) 11 to 15 Ω



c.

Connect a positive (+) lead from the battery to the terminal of the solenoid valve connector, and a negative (-) lead to the solenoid body. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

NG