Home › Drivetrain › UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › from 2016.11
RM3160E _52 Drivetrain _060164 UA80E AUTOMATIC TRANSMISSION / TRANSAXLE _0298261 AUTOMATIC TRANSAXLE SYSTEM C

UA80E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P07457F  Pressure Control Solenoid "A" Actuator Stuck Off  


DESCRIPTION

Based on signals from the transmission revolution sensors (NT and NC), the actual gear is detected.

The ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical malfunctions of the solenoid valves, transmission valve body assembly and automatic transaxle assembly (clutch, brake, gear, etc.).

HINT:
Actual gear when solenoid (SL1) valve malfunction occurs (without fail-safe control):
ECM commanded gear 1st 2nd 3rd 4th 5th 6th 7th 8th

*: Neutral

Actual gear during SL1 stuck ON malfunction 1st 2nd 3rd 4th 5th 4th to 5th 3rd to 5th 5th
Actual gear during SL1 stuck OFF malfunction N* N* N* N* N* 6th 7th 8th


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P07457F Pressure Control Solenoid "A" Actuator Stuck Off 1. Diagnosis Condition, 2. Malfunction Status, 3. Malfunction Time, 4. Other
SL1 stuck ON malfunction:
1.

Engine coolant temperature is 40°C (104°F) or higher, ATF temperature is -10°C (14°F) or higher, and the vehicle is being driven with the shift lever in D (no malfunctions are detected in the solenoid (SL1, SL2, SL3, SL4, SL5, SL6, SL, SLU and SLT) valves, transmission revolution sensors (NT and NC), coolant temperature sensor, oil temperature sensor, knock sensor, crankshaft position sensor circuit, electronic throttle or CAN2)

2.

When the ECM commands the transaxle to shift to 6th, 7th or 8th gear, the actual gear changes to 5th gear.

3.

Malfunction status continues for 0.8 seconds or more

4.

2-trip detection logic


SL1 stuck OFF malfunction:
1.

Engine coolant temperature is 40°C (104°F) or higher, ATF temperature is -10°C (14°F) or higher, and the vehicle is being driven with the shift lever in D (no malfunctions are detected in the solenoid (SL1, SL2, SL3, SL4, SL5, SL6, SL, SLU and SLT) valves, transmission revolution sensors (NT and NC), coolant temperature sensor, oil temperature sensor, knock sensor, crankshaft position sensor circuit, electronic throttle or CAN2)

2.

When the ECM commands the transaxle to shift to 1st, 2nd, 3rd, 4th or 5th gear, the engine overruns (neutral status).

3.

Malfunction status continues for 0.5 seconds or more

4.

2-trip detection logic


·

Solenoid (SL1) valve

·

Solenoid (SL2) valve

·

Solenoid (SL3) valve

·

Solenoid (SL4) valve

·

Solenoid (SL5) valve

·

Solenoid (SL6) valve

·

Solenoid (SL) valve

·

Solenoid (SLU) valve

·

Solenoid (SLT) valve

·

Transmission valve body assembly

·

Torque converter assembly

·

Automatic transaxle assembly (clutch, brake, gear, etc.)


Comes on DTC stored SAE Code:
P0746

MONITOR DESCRIPTION

The ECM commands gear shifts by turning the solenoid valves on and off. According to the input shaft revolution (speed) and output shaft revolution (speed), the ECM detects the actual gear (1st, 2nd, 3rd, 4th, 5th, 6th, 7th or 8th gear). When the gear commanded by the ECM and the actual gear are not the same, the ECM illuminates the MIL and stores a DTC.

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


HINT:

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Perform the D Position Shift Test inspection in Road Test.

Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>ROAD TEST

2.

Turn the ignition switch off.

3.

Perform step (1) again.



PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P07457F)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Transmission / Trouble Codes.


e.

Read the DTCs using the GTS.

Result:
Result Proceed to
DTC P07457F and DTC P07407E, P07757F, P07957F, P08BA7F, P27137F, P28077F and/or P28167F are output A
Only DTC P07457F is output B
DTCs other than P07457F, P07407E, P07757F, P07957F, P08BA7F, P27137F, P28077F and P28167F are also output C


HINT:
·

If any DTCs other than P07457F, P07407E, P07757F, P07957F, P08BA7F, P27137F, P28077F and P28167F are output, perform troubleshooting for those DTCs first.

·

If a solenoid valve is stuck ON or OFF, DTCs for several solenoid valves including the malfunctioning solenoid valve will be stored.





A

2.CLEAR DTC AND PERFORM STALL SPEED TEST

B

3.INSPECT SOLENOID (SL1), (SL2), (SL3), (SL4), (SL5) AND (SL6) VALVE

C

2.CLEAR DTC AND PERFORM STALL SPEED TEST
a.

Clear the DTCs.

Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>DTC CHECK / CLEAR

HINT:

Write down the currently output DTCs before clearing them.


Powertrain > Transmission > Clear DTCs
50002 373

b.

Perform the stall speed test.

Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>MECHANICAL SYSTEM TESTS

Result:
Test Condition Proceed to
Stall speed test can be performed A
Stall speed test cannot be performed B




A

3.INSPECT SOLENOID (SL1), (SL2), (SL3), (SL4), (SL5) AND (SL6) VALVE

B

5.INSPECT SOLENOID (SLT) VALVE
3.INSPECT SOLENOID (SL1), (SL2), (SL3), (SL4), (SL5) AND (SL6) VALVE
a.
C197715C76
1.75,1 2.198,0.417 true 1.5,1.01 1.042,0.427 true 1.75,2.979 2.198,2.385 true 1.479,2.979 1.021,2.385 true 0.073,0.083 0.469,0.344 0.396,0.26 10 false *a 2.25,0.24 2.521,0.5 0.271,0.26 10 false 1 0.896,0.25 1.156,0.5 0.26,0.25 10 false 2 2.281,2.198 2.521,2.479 0.24,0.281 10 false 1 0.875,2.219 1.156,2.49 0.281,0.271 10 false 2 1.865,3.948 2.271,4.271 0.406,0.323 10 false (+) 1.219,3.948 1.594,4.25 0.375,0.302 10 false (-)
*a Component without harness connected
(Solenoid (SL1), (SL2), (SL3), (SL4), (SL5) and (SL6) Valves)


Remove the solenoid (SL1), (SL2), (SL3), (SL4), (SL5) and (SL6) valves.

Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Solenoid (SL1) valve connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω
Solenoid (SL2) valve connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω
Solenoid (SL3) valve connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω
Solenoid (SL4) valve connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω
Solenoid (SL5) valve connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω
Solenoid (SL6) valve connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

4.INSPECT SOLENOID (SL) VALVE

NG

REPLACE SOLENOID (SL1), (SL2), (SL3), (SL4), (SL5) OR (SL6) VALVE

4.INSPECT SOLENOID (SL) VALVE
a.
C361133C03
0.094,0.083 0.406,0.281 0.313,0.198 10 false *1 2.583,0.24 3.042,0.438 0.458,0.198 10 false (+) 1.594,0.26 2.052,0.458 0.458,0.198 10 false (-)
*1 Solenoid (SL) Valve


Remove the solenoid (SL) valve.

Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Solenoid (SL) valve connector terminal - Solenoid (SL) valve body 20°C (68°F) 11 to 15 Ω



c.

Connect a positive (+) lead from the battery to the terminal of the solenoid valve connector, and a negative (-) lead to the solenoid body. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

5.INSPECT SOLENOID (SLT) VALVE

NG

5.INSPECT SOLENOID (SLT) VALVE
a.
C197715C76
1.75,1 2.198,0.417 true 1.5,1.01 1.042,0.427 true 1.75,2.979 2.198,2.385 true 1.479,2.979 1.021,2.385 true 0.073,0.083 0.469,0.344 0.396,0.26 10 false *a 2.25,0.24 2.521,0.5 0.271,0.26 10 false 1 0.896,0.25 1.156,0.5 0.26,0.25 10 false 2 2.281,2.198 2.521,2.479 0.24,0.281 10 false 1 0.875,2.219 1.156,2.49 0.281,0.271 10 false 2 1.865,3.948 2.271,4.271 0.406,0.323 10 false (+) 1.219,3.948 1.594,4.25 0.375,0.302 10 false (-)
*a Component without harness connected
(Solenoid (SLT) Valve)


Remove the solenoid (SLT) valve.

Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Solenoid (SLT) valve connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

6.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

6.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
a.

Inspect the transmission valve body assembly.

Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>REMOVAL

OK:

There is no foreign matter on each valve and they operate smoothly.



Result:
Proceed to
OK
NG



OK

7.INSPECT TORQUE CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

7.INSPECT TORQUE CONVERTER ASSEMBLY
a.

Inspect the torque converter assembly.

Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>TORQUE CONVERTER AND DRIVE PLATE>INSPECTION

OK:

The torque converter assembly is normal.



Result:
Proceed to
OK
NG



OK

8.REPAIR OR REPLACE AUTOMATIC TRANSAXLE ASSEMBLY

NG

8.REPAIR OR REPLACE AUTOMATIC TRANSAXLE ASSEMBLY

Result:
Proceed to
NEXT



NEXT