Home › Drivetrain › UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSAXLE SYSTEM › 2016.11–2017.10
RM3160E _52 Drivetrain _060164 UA80E AUTOMATIC TRANSMISSION / TRANSAXLE _0298261 AUTOMATIC TRANSAXLE SYSTEM C

UA80E AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P08BA12  Pressure Control Solenoid "L" Circuit Short to Battery  


DESCRIPTION

Changing gears is performed by the ECM turning the solenoid (SL1, SL2, SL3, SL4, SL5 and SL6) valves on and off.

If an open or short occurs in any of the solenoid valve circuits, the ECM controls the remaining normal solenoid valves to allow the vehicle to be driven. If all of the solenoid valves are malfunctioning, only the mechanical fluid pressure circuit will function and some manual operation will be possible. If an open or short occurs in a solenoid valve circuit, the ECM cuts power to the malfunctioning solenoid valve.

HINT:

The following table shows normal operation of the solenoid (SL6) valve when the shift lever is in D.

Solenoid Valve Operation:
Gear 1st 2nd 3rd 4th 5th 6th 7th 8th
Solenoid (SL6) Valve ON OFF OFF OFF OFF OFF OFF OFF


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P08BA12 Pressure Control Solenoid "L" Circuit Short to Battery 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other
1.

Driving so that gear changes occur

2.

Solenoid (SL6) valve circuit is short to +B

3.

1 second

4.

1-trip detection logic


·

Solenoid (SL6) valve

·

Transmission wire

·

Harness and connector

·

ECM


Comes on DTC stored SAE Code:
P08C2

MONITOR DESCRIPTION

This DTC indicates a short to +B in the solenoid (SL6) valve circuit. The ECM commands gear shifts by turning the solenoid valves on or off. When there is an open or short in any solenoid valve circuit, the ECM detects the problem, illuminates the MIL and stores a DTC.

The ECM performs the fail-safe function and turns the other normal solenoid valves on or off. In the case of an open or short circuit, the ECM stops sending current to the open or shorted solenoid.

WIRING DIAGRAM

C334263E62
1.01,2.802 1.469,3 0.458,0.198 10 false C62 1.021,2.969 2.854,3.167 1.833,0.198 10 false Transmission Wire 1.083,1.583 2.729,2.094 1.646,0.51 10 false Solenoid (SL6) Valve 0.74,1.219 0.896,1.417 0.156,0.198 10 false 1 0.75,1.958 0.906,2.156 0.156,0.198 10 false 2 5.25,0.844 5.865,1.042 0.615,0.198 10 false SL6+ 5.24,2.063 5.854,2.26 0.615,0.198 10 false SL6- 4.969,0.844 5.281,1.042 0.313,0.198 10 false 32 4.969,2.063 5.281,2.26 0.313,0.198 10 false 33 5.781,2.844 6.24,3.042 0.458,0.198 10 false C1 5.781,3 6.5,3.385 0.719,0.385 10 false ECM 5.969,0.615 6.583,0.813 0.615,0.198 10 false 12 V 2.458,0.844 3.073,1.042 0.615,0.198 10 false SL6+ 2.479,2.073 3.094,2.271 0.615,0.198 10 false SL6- 2.906,0.844 3.219,1.042 0.313,0.198 10 false 9 2.917,2.073 3.229,2.271 0.313,0.198 10 false 8

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


HINT:

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.



PROCEDURE

1.CHECK HARNESS AND TRANSMISSION WIRE (TRANSMISSION WIRE (SOLENOID (SL6) VALVE) - ECM)
a.

Disconnect the C1 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C1-32 (SL6+) or C1-33 (SL6-) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.REPLACE ECM

NG

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
2.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)
a.

Disconnect the C62 transmission wire connector.


b.

Disconnect the C1 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C62-9 (SL6+) or C1-32 (SL6+) - Other terminals Always 10 kΩ or higher
C62-8 (SL6-) or C1-33 (SL6-) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT SOLENOID (SL6) VALVE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)

4.INSPECT SOLENOID (SL6) VALVE
a.
C197715C76
1.75,1 2.198,0.417 true 1.5,1.01 1.042,0.427 true 1.75,2.979 2.198,2.385 true 1.479,2.979 1.021,2.385 true 0.073,0.083 0.469,0.344 0.396,0.26 10 false *a 2.25,0.24 2.521,0.5 0.271,0.26 10 false 1 0.896,0.25 1.156,0.5 0.26,0.25 10 false 2 2.281,2.198 2.521,2.479 0.24,0.281 10 false 1 0.875,2.219 1.156,2.49 0.281,0.271 10 false 2 1.865,3.948 2.271,4.271 0.406,0.323 10 false (+) 1.219,3.948 1.594,4.25 0.375,0.302 10 false (-)
*a Component without harness connected
(Solenoid (SL6) Valve)


Remove the solenoid (SL6) valve.

Click hereDrivetrain>UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Solenoid (SL6) valve connector terminal 1 - terminal 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Connect a positive (+) lead from the battery with a 21 W bulb to terminal 1 and a negative (-) lead to terminal 2 of the solenoid valve connector. Check that the valve moves and makes an operating sound.

OK:

Valve moves and makes an operating sound.



Result:
Proceed to
OK
NG



OK

NG