Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2016.11
RM3160E _56 Audio / Visual / Telematics _019702 PARK ASSIST / MONITORING _0298312 PANORAMIC VIEW MONITOR SYSTEM J

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  "CHK" message(s) are displayed on the SIGNAL CHECK screen.  


DESCRIPTION

On the SIGNAL CHECK screen, it is possible to check if the signals sent to the parking assist ECU are normal.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DTC CHECK / CLEAR

HINT:
·

On the SIGNAL CHECK screen, "OK" (blue) is displayed for items with a normal inspection result or input state.

·

On the SIGNAL CHECK screen, "CHK" (red) is displayed for items with an abnormal inspection result or input state.

·

Displayed items may differ depending on vehicle specifications.



Item Signal Input Method Detail DTC Output when Abnormal Result is Displayed Signal Receiver
CAN CAN communication CAN communication signal DTC is output Related ECUs
CAMERA SW Vehicle wire harness Panoramic view monitor switch signal input state DTC is not output Panoramic View Monitor Switch

WIRING DIAGRAM

E336305E03
5.115,0.521 5.729,0.719 0.615,0.198 10 false BLSW 5.052,2.115 5.542,2.344 0.49,0.229 10 false F131 5.063,2.271 6.667,2.594 1.604,0.323 10 false Parking Assist ECU 2.969,1.479 4.458,1.969 1.49,0.49 10 false to CAN Communication Line 0.938,2.24 2.927,2.583 1.99,0.344 10 false : to CAN Communication Line 1.677,0.938 3.198,1.448 1.521,0.51 10 false Panoramic View Monitor Switch 1.677,0.771 2.073,1.042 0.396,0.271 10 false F129 1.875,0.417 2.219,0.688 0.344,0.271 10 false 8 3.219,0.417 3.563,0.688 0.344,0.271 10 false 11 4.875,0.417 5.219,0.688 0.344,0.271 10 false 20 2.063,0.417 2.406,0.688 0.344,0.271 10 false E 3.031,0.417 3.375,0.688 0.344,0.271 10 false D

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the multi-display after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK DISPLAY CHECK MODE
a.
E334364

Check which items display on the signal check screen.


Result:
Result Proceed to
"CAMERA SW" displays "CHK" (red) A
"CAN" displays "CHK" (red) B



A

2.CHECK HARNESS AND CONNECTOR (PANORAMIC VIEW MONITOR SWITCH - PARKING ASSIST ECU AND BODY GROUND)

B

2.CHECK HARNESS AND CONNECTOR (PANORAMIC VIEW MONITOR SWITCH - PARKING ASSIST ECU AND BODY GROUND)
a.

Disconnect the F129 panoramic view monitor switch connector.


b.

Disconnect the F131 parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F131-20 (BLSW) - F129-11 (D) Always Below 1 Ω
F129-5 (E) - Body ground Always Below 1 Ω
F131-20 (BLSW) or F129-11 (D) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT PANORAMIC VIEW MONITOR SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT PANORAMIC VIEW MONITOR SWITCH


Result:
Proceed to
OK
NG



OK

NG