Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2016.11
RM3160E _56 Audio / Visual / Telematics _019702 PARK ASSIST / MONITORING _0298312 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1684  Side Camera Current Malfunction  


DESCRIPTION

This DTC is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the passenger side television camera assembly to the parking assist ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1684 Side Camera Current Malfunction Side camera current malfunction
·

Harness or connector

·

Parking assist ECU

·

Side television camera assembly RH (for LHD)

·

Outer rear view mirror assembly RH (for LHD)

·

Side television camera assembly LH (for RHD)

·

Outer rear view mirror assembly LH (for RHD)



WIRING DIAGRAM

for LHD


E288342E07
0.521,1.927 1.927,2.365 1.406,0.438 10 false Side Television Camera Assembly RH 2.917,2.063 4.385,2.469 1.469,0.406 10 false Outer Rear View Mirror Assembly RH 5.594,2.146 6.875,2.531 1.281,0.385 10 false Parking Assist ECU 5.594,1.99 6.01,2.198 0.417,0.208 10 false F130 5.75,1.229 6.365,1.427 0.615,0.198 10 false RCB+ 5.75,1.635 6.365,1.833 0.615,0.198 10 false RGND 5.479,1.125 6.094,1.323 0.615,0.198 10 false 6 5.49,1.521 6.104,1.719 0.615,0.198 10 false 18 2.927,1.906 3.542,2.104 0.615,0.198 10 false H18 3.958,1.51 4.573,1.708 0.615,0.198 10 false 2 3.948,1.125 4.563,1.323 0.615,0.198 10 false 3 3.448,1.208 4.063,1.406 0.615,0.198 10 false RCB+ 3.427,1.583 4.042,1.781 0.615,0.198 10 false RGND 4.823,1.51 5.583,1.729 0.76,0.219 10 false * 2.188,1.51 2.948,1.729 0.76,0.219 10 false * 4.417,2.375 5.177,2.594 0.76,0.219 10 false *: Shielded


for RHD


E288342E08
0.521,1.917 1.927,2.354 1.406,0.438 10 false Side Television Camera Assembly LH 2.917,2.063 4.385,2.469 1.469,0.406 10 false Outer Rear View Mirror Assembly LH 5.594,2.146 6.875,2.531 1.281,0.385 10 false Parking Assist ECU 5.594,1.99 6.01,2.198 0.417,0.208 10 false F130 5.75,1.229 6.365,1.427 0.615,0.198 10 false LCB+ 5.75,1.635 6.365,1.833 0.615,0.198 10 false LGND 5.479,1.125 6.094,1.323 0.615,0.198 10 false 12 5.49,1.521 6.104,1.719 0.615,0.198 10 false 24 2.927,1.906 3.542,2.104 0.615,0.198 10 false I17 3.958,1.51 4.573,1.708 0.615,0.198 10 false 2 3.948,1.125 4.563,1.323 0.615,0.198 10 false 3 3.458,1.208 4.073,1.406 0.615,0.198 10 false LCB+ 3.417,1.583 4.031,1.781 0.615,0.198 10 false LGND 4.823,1.51 5.583,1.729 0.76,0.219 10 false * 2.188,1.51 2.948,1.729 0.76,0.219 10 false * 4.417,2.375 5.177,2.594 0.76,0.219 10 false *: Shielded


CAUTION / NOTICE / HINT

NOTICE:
·

When "!" mark is displayed on the multi-display after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DTC CHECK / CLEAR

Chassis > Panoramic View Monitor > Clear DTCs
50002 353

b.

Check for DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DTC CHECK / CLEAR

Chassis > Panoramic View Monitor > Trouble Codes
50001 353
OK:

DTC C1684 is not output.



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

B

2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY RH)

C

6.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY LH)
2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY RH)
a.

Disconnect the F130 parking assist ECU connector.


b.

Disconnect the H18 outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F130-6 (RCB+) - H18-3 (RCB+) Always Below 1 Ω
F130-18 (RGND) - H18-2 (RGND) Always Below 1 Ω
F130-6 (RCB+) or H18-3 (RCB+) - Body ground Always 10 kΩ or higher
F130-18 (RGND) or H18-2 (RGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK PARKING ASSIST ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK PARKING ASSIST ECU
a.
E272332C84
1.521,0.146 1.906,0.375 0.385,0.229 0.5,0.5 0.667,0.5 0.667,0.5 0.833,1.073 true 1.073,2.01 0.906,2.01 0.906,2.01 0.844,1.26 true 0.083,0.073 0.396,0.229 0.313,0.156 10 false *a 1.573,0.167 2.031,0.365 0.458,0.198 10 false F130 1.125,1.917 1.74,2.115 0.615,0.198 10 false RGND 0.094,0.406 0.708,0.604 0.615,0.198 10 false RCB+
*a Component with harness connected
(Parking Assist ECU)


Remove the parking assist ECU with the connector still connected.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F130-18 (RGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F130-6 (RCB+) - F130-18 (RGND) Ignition switch ACC 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

4.REPLACE SIDE TELEVISION CAMERA ASSEMBLY RH

NG

4.REPLACE SIDE TELEVISION CAMERA ASSEMBLY RH
a.

Replace the side television camera assembly RH with a new or normally functioning one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA(for Side)>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DTC CHECK / CLEAR

Chassis > Panoramic View Monitor > Clear DTCs
50002 353

b.

Check for DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DTC CHECK / CLEAR

Chassis > Panoramic View Monitor > Trouble Codes
50001 353
OK:

DTCs C1684 is not output.



Result:
Proceed to
OK
NG



OK

END (SIDE TELEVISION CAMERA ASSEMBLY RH IS DEFECTIVE)

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

6.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY LH)
a.

Disconnect the F130 parking assist ECU connector.


b.

Disconnect the I17 outer rear view mirror assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F130-12 (LCB+) - I17-3 (LCB+) Always Below 1 Ω
F130-24 (LGND) - I17-2 (LGND) Always Below 1 Ω
F130-12 (LCB+) or I17-3 (LCB+) - Body ground Always 10 kΩ or higher
F130-24 (LGND) or I17-2 (LGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK PARKING ASSIST ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK PARKING ASSIST ECU
a.
E272332C83
1.521,0.167 1.917,0.396 0.396,0.229 2.344,1.969 2.177,1.969 2.177,1.969 1.865,1.385 true 2.458,0.365 2.292,0.365 2.292,0.365 1.865,1.188 true 0.146,0.115 0.458,0.271 0.313,0.156 10 false *a 1.563,0.188 2.021,0.385 0.458,0.198 10 false F130 2.406,1.885 3.021,2.083 0.615,0.198 10 false LGND 2.521,0.271 3.135,0.469 0.615,0.198 10 false LCB+
*a Component with harness connected
(Parking Assist ECU)


Remove the parking assist ECU with the connector still connected.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F130-24 (LGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F130-12 (LCB+) - F130-24 (LGND) Ignition switch ACC 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

8.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH

NG

8.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH
a.

Replace the side television camera assembly LH with a new or normally functioning one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA(for Side)>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DTC CHECK / CLEAR

Chassis > Panoramic View Monitor > Clear DTCs
50002 353

b.

Check for DTCs.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DTC CHECK / CLEAR

Chassis > Panoramic View Monitor > Trouble Codes
50001 353
OK:

DTC C1684 is not output.



Result:
Proceed to
OK
NG



OK

END (SIDE TELEVISION CAMERA ASSEMBLY LH IS DEFECTIVE)

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH