This DTC is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the driver side television camera assembly to the parking assist ECU.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1687 | Over Current Detected in Driver Side Camera | Side camera current malfunction | ·
Harness or connector ·
Parking assist ECU ·
Side television camera assembly LH (for LHD) ·
Outer rear view mirror assembly LH (for LHD) ·
Side television camera assembly RH (for RHD) ·
Outer rear view mirror assembly RH (for RHD) |
for LHD
for RHD
When "!" mark is displayed on the multi-display after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION
Clear the DTCs.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DTC CHECK / CLEAR
Check for DTCs.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DTC CHECK / CLEAR
DTC C1687 is not output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Disconnect the F130 parking assist ECU connector.
Disconnect the I17 outer rear view mirror assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F130-12 (LCB+) - I17-3 (LCB+) | Always | Below 1 Ω |
| F130-24 (LGND) - I17-2 (LGND) | Always | Below 1 Ω |
| F130-12 (LCB+) or I17-3 (LCB+) - Body ground | Always | 10 kΩ or higher |
| F130-24 (LGND) or I17-2 (LGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Parking Assist ECU) |
Remove the parking assist ECU with the connector still connected.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F130-24 (LGND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F130-12 (LCB+) - F130-24 (LGND) | Ignition switch ACC | 5.5 to 7.05 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the side television camera assembly LH with a new or normally functioning one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA(for Side)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DTC CHECK / CLEAR
Check for DTCs.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DTC CHECK / CLEAR
DTC C1687 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F130 parking assist ECU connector.
Disconnect the H18 outer rear view mirror assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F130-6 (RCB+) - H18-3 (RCB+) | Always | Below 1 Ω |
| F130-18 (RGND) - H18-2 (RGND) | Always | Below 1 Ω |
| F130-6 (RCB+) or H18-3 (RCB+) - Body ground | Always | 10 kΩ or higher |
| F130-18 (RGND) or H18-2 (RGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Parking Assist ECU) |
Remove the parking assist ECU with the connector still connected.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F130-18 (RGND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F130-6 (RCB+) - F130-18 (RGND) | Ignition switch ACC | 5.5 to 7.05 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the side television camera assembly RH with a new or normally functioning one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA(for Side)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DTC CHECK / CLEAR
Check for DTCs.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>DTC CHECK / CLEAR
DTC C1687 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG