Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › ULTRASONIC SENSOR(for Rear Side) › from 2016.11
RM3160E _56 Audio / Visual / Telematics _019702 PARK ASSIST / MONITORING _0108148 ULTRASONIC SENSOR(for Rear Side) A

PARK ASSIST / MONITORING  ULTRASONIC SENSOR(for Rear Side)  INSTALLATION  


PROCEDURE

Hide 89348R 1.INSTALL REAR CORNER ULTRASONIC SENSOR RETAINER

HINT:
·

Perform this procedure only when replacement of the rear corner ultrasonic sensor retainer is necessary.

·

If a rear corner ultrasonic sensor retainer has been removed, replace it with a new one. Install the No. 1 ultrasonic sensor with a new rear corner ultrasonic sensor retainer as a set to the rear bumper assembly.

·

Use the same procedure for the RH side and LH side.



a.
E351849

Engage the 2 claws and install a new rear corner ultrasonic sensor retainer to the No. 1 ultrasonic sensor.


b.

Clean the rear bumper assembly surface.

i.

Remove any remaining double-sided tape from the rear bumper assembly.


ii.

Wipe off any tape adhesive residue with cleaner.



c.
E335575C03
1.719,1.125 1.938,1.292 0.219,0.167 10 true *a
*a 18 mm (0.709 in.)


Cover the sensor installation hole with a 18 mm (0.709 in.) circular piece of tape.


d.
E351678C01
0,0 0,0 false
V100144

Primer


Using a brush or felt, apply primer or equivalent to the rear corner ultrasonic sensor retainer installation area.

NOTICE:
·

Use a clean brush or felt.

·

Do not touch the rear bumper assembly until the primer has dried.




e.

Confirm that the primer has completely dried by touching the rear bumper assembly. Then remove the tape.


f.

Peel off the release paper from the new rear corner ultrasonic sensor retainer.


g.
E359872C01
2.365,1.385 2.365,1.115 true 2.719,0.906 2.99,0.906 true 2.302,1.396 2.521,1.583 0.219,0.188 10 true *a 3.01,0.813 3.229,1 0.219,0.188 10 true *b
*a Scribed line
*b Protrusion of the mark


Align the rear corner ultrasonic sensor retainer with No. 1 ultrasonic sensor with the mark on the rear bumper assembly and install it as shown in the illustration.

NOTICE:
·

Ensure that the sensor tip is correctly inserted into the sensor installation hole of the rear bumper assembly.

·

Ensure that the rear corner ultrasonic sensor retainer is within the scribed line.

·

The double-sided tape of a rear corner ultrasonic sensor retainer will deteriorate if it is detached. Make sure to replace the rear corner ultrasonic sensor retainer with a new one when reattachment is necessary.



HINT:
·

Align the connector with the protrusion of the mark when connecting it.

·

Press the rear corner ultrasonic sensor retainer with a force of 30 N (3.0 kgf) for 3 seconds and install the rear corner ultrasonic sensor retainer firmly so that there is no clearance between the rear corner ultrasonic sensor retainer and rear bumper assembly.




Hide 89348S 2.INSTALL REAR CENTER ULTRASONIC SENSOR RETAINER

HINT:
·

Perform this procedure only when replacement of the rear center ultrasonic sensor retainer is necessary.

·

If a rear center ultrasonic sensor retainer has been removed, replace it with a new one. Install the No. 1 ultrasonic sensor with a new rear center ultrasonic sensor retainer as a set to the rear bumper assembly.

·

Use the same procedure for the RH side and LH side.



a.
E357411

Engage the 2 claws and install a new rear center ultrasonic sensor retainer to the No. 1 ultrasonic sensor.


b.

Clean the rear bumper assembly surface.

i.

Remove any remaining double-sided tape from the rear bumper assembly.


ii.

Wipe off any tape adhesive residue with cleaner.



c.
E335575C03
1.719,1.125 1.938,1.292 0.219,0.167 10 true *a
*a 18 mm (0.709 in.)


Cover the sensor installation hole with a 18 mm (0.709 in.) circular piece of tape.


d.
E351677C02
0,0 0,0 false
V100144

Primer


Using a brush or felt, apply primer or equivalent to the rear center ultrasonic sensor retainer installation area.

NOTICE:
·

Use a clean brush or felt.

·

Do not touch the rear bumper assembly until the primer has dried.




e.

Confirm that the primer has completely dried by touching the rear bumper assembly. Then remove the tape.


f.

Peel off the release paper from the new rear center ultrasonic sensor retainer.


g.
E357412C01
1.104,1.771 1.104,1.469 true 0.344,1.083 0.583,1.083 true 1.042,1.781 1.26,1.979 0.219,0.198 10 true *a 0.135,0.979 0.354,1.177 0.219,0.198 10 true *b
*a Scribed line
*b Protrusion of the mark


Align the rear center ultrasonic sensor retainer with No. 1 ultrasonic sensor with the mark on the rear bumper assembly and install it as shown in the illustration.

NOTICE:
·

Ensure that the sensor tip is correctly inserted into the sensor installation hole of the rear bumper assembly.

·

Ensure that the rear center ultrasonic sensor retainer is within the scribed line.

·

The double-sided tape of a rear center ultrasonic sensor retainer will deteriorate if it is detached. Make sure to replace the rear center ultrasonic sensor retainer with a new one when reattachment is necessary.



HINT:
·

Align the connector with the protrusion of the mark when connecting it.

·

Press the rear center ultrasonic sensor retainer with a force of 30 N (3.0 kgf) for 3 seconds and install the rear center ultrasonic sensor retainer firmly so that there is no clearance between the rear center ultrasonic sensor retainer and rear bumper assembly.




Hide 52615 3.INSTALL REAR BUMPER ENERGY ABSORBER

HINT:

Perform this procedure only when replacement of the rear center ultrasonic sensor retainers is necessary.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>REAR BUMPER>REASSEMBLY


Hide 82183 4.INSTALL NO. 3 LUGGAGE ROOM WIRE

HINT:

Perform this procedure only when replacement of the rear center ultrasonic sensor retainers is necessary.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>REAR BUMPER>REASSEMBLY


Hide 89342 5.INSTALL NO. 1 ULTRASONIC SENSOR (for Corner Sensor)

HINT:

Use the same procedure for the RH side and LH side.


a.

When replacing only the No. 1 ultrasonic sensor:

i.

Engage the 2 claws to install the No. 1 ultrasonic sensor.



b.

Connect the connector.


Hide 89342A 6.INSTALL NO. 1 ULTRASONIC SENSOR (for Back Sensor)

HINT:

Use the same procedure for the RH side and LH side.


a.

When replacing only the No. 1 ultrasonic sensor:

i.

Engage the 2 claws to install the No. 1 ultrasonic sensor.



b.

Connect the connector.


Hide 7.INSTALL REAR BUMPER ASSEMBLY