Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Radio and Display Type) › from 2016.11
RM3160E _56 Audio / Visual / Telematics _019701 NAVIGATION / MULTI INFO DISPLAY _0101135 NAVIGATION SYSTEM(for Radio and Display Type) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Radio and Display Type)  B15D8  Monitor Disconnected  


DESCRIPTION

The radio and display receiver assembly and parking assist ECU communicate via AVC-LAN communication.

This DTC is stored when an AVC-LAN communication error occurs between the radio and display receiver assembly and parking assist ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15D8 Monitor Disconnected The parking assist ECU was not connected while the engine switch was on (ACC) or on (IG)
·

AVC-LAN circuit

·

Parking assist ECU

·

Radio and display receiver assembly

·

Harness or connector



HINT:
·

Even if no fault is present, this DTC may be stored depending on the battery condition.

·

The radio and display receiver assembly is the master unit.



WIRING DIAGRAM

E356778E01
3.823,0.677 4.844,0.948 1.021,0.271 10 false MPX-B NO. 3 3.896,1.438 4.667,1.635 0.771,0.198 10 false ECU-ACC 3.885,2.229 4.604,2.438 0.719,0.208 10 false IG1 NO. 3 5.052,1.333 5.99,1.573 0.938,0.24 10 false ACC Relay 5.042,0.521 6.208,0.729 1.167,0.208 10 false from Battery 5.063,2.104 6.677,2.333 1.615,0.229 10 false from IG1 NO. 3 Relay 4.74,3.25 6.875,3.479 2.135,0.229 10 false : AVC-LAN Communication Line 0.729,1.25 1.125,1.469 0.396,0.219 10 false TX3+ 0.74,1.542 1.073,1.75 0.333,0.208 10 false TX3- 2.396,2.135 2.844,2.313 0.448,0.177 10 false GND1 2.406,1.552 2.646,1.719 0.24,0.167 10 false TX- 2.396,1.26 2.833,1.438 0.438,0.177 10 false TX+ 3.073,0.531 3.333,0.719 0.26,0.188 10 false +B 2.99,1.323 3.344,1.5 0.354,0.177 10 false ACC 3.125,2.115 3.385,2.313 0.26,0.198 10 false IG 2.24,1.427 2.417,1.594 0.177,0.167 10 false 9 2.177,1.125 2.396,1.313 0.219,0.188 10 false 10 1.104,1.135 1.323,1.323 0.219,0.188 10 false 7 1.104,1.427 1.323,1.615 0.219,0.188 10 false 8 3.354,0.448 3.573,0.635 0.219,0.188 10 false 2 3.354,1.229 3.573,1.417 0.219,0.188 10 false 1 3.354,2.021 3.573,2.208 0.219,0.188 10 false 6 2.25,2.052 2.469,2.24 0.219,0.188 10 false 3 0.083,3.042 1.375,3.49 1.292,0.448 10 false Radio and Display Receiver Assembly 0.083,2.885 0.417,3.094 0.333,0.208 10 false F72 2.333,3.042 3.604,3.271 1.271,0.229 10 false Parking Assist ECU 2.344,2.865 2.771,3.083 0.427,0.219 10 false F131

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check that optional components (including associated wiring) which generate radio waves are not installed.

Result:
Result Proceed to
Optional components (including associated wiring) are installed. A
Optional components (including associated wiring) are not installed. B


HINT:
·

Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

·

This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.





A

2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

3.CHECK DTC
2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Remove optional components (including associated wiring).

NOTICE:

Do not remove optional components or associated wiring without the permission of the customer.



Result:
Proceed to
NEXT



NEXT

3.CHECK DTC
3.CHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Radio and Display Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

4.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU POWER SOURCE)
4.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU POWER SOURCE)
a.

Disconnect the F131 parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F131-3 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F131-2 (+B) - F131-3 (GND1) Always 11 to 14 V
F131-1 (ACC) - F131-3 (GND1) Engine switch on (ACC) 11 to 14 V
F131-6 (IG) - F131-3 (GND1) Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARKING ASSIST ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - PARKING ASSIST ECU)
a.

Disconnect the F72 radio and display receiver assembly connector.


b.

Disconnect the F131 parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F72-7 (TX3+) - F131-10 (TX+) Always Below 1 Ω
F72-8 (TX3-) - F131-9 (TX-) Always Below 1 Ω
F72-7 (TX3+) or F131-10 (TX+) - Body ground Always 10 kΩ or higher
F72-8 (TX3-) or F131-9 (TX-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.REPLACE PARKING ASSIST ECU

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

6.REPLACE PARKING ASSIST ECU
a.

Replace the parking assist ECU with a new or known good one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Navigation Receiver Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY