Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for Navigation Receiver Type) › from 2016.11
RM3160E _56 Audio / Visual / Telematics _019701 NAVIGATION / MULTI INFO DISPLAY _0104171 NAVIGATION SYSTEM(for Navigation Receiver Type) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for Navigation Receiver Type)  B15D8  Monitor Disconnected  


DESCRIPTION

The navigation receiver assembly and parking assist ECU are connected via AVC-LAN communication.

This DTC is stored when an AVC-LAN communication error occurs between the navigation receiver assembly and parking assist ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15D8 Monitor Disconnected The parking assist ECU was not connected while the engine switch was on (ACC) or on (IG)
·

AVC-LAN circuit between navigation receiver assembly and parking assist ECU

·

Parking assist ECU power source circuit

·

Parking assist ECU

·

Navigation receiver assembly

·

Harness or connector



HINT:

The navigation receiver assembly is the master unit.


WIRING DIAGRAM

E334472E14
0.99,4.396 3.021,4.656 2.031,0.26 10 false : AVC-LAN Communication Line 5.594,3.969 6.948,4.219 1.354,0.25 10 false Parking Assist ECU 1.552,1.615 2.479,1.865 0.927,0.25 10 false from Battery 1.313,2.177 2.406,2.406 1.094,0.229 10 false from ACC Relay 0.99,2.74 2.438,2.948 1.448,0.208 10 false from IG1-NO. 3 Relay 3.219,1.26 5.146,1.448 1.927,0.188 10 false Navigation Receiver Assembly 3.313,1.781 4.219,2.021 0.906,0.24 10 false MPX-B NO. 3 3.396,2.354 4.135,2.615 0.74,0.26 10 false ECU-ACC 3.406,2.917 4.5,3.188 1.094,0.271 10 false IG1 NO. 3 5.604,3.802 5.948,4.063 0.344,0.26 10 false F131 3.229,1.094 3.573,1.281 0.344,0.188 10 false F117 4.094,0.354 4.49,0.615 0.396,0.26 10 false TX3+ 4.125,0.75 4.469,1.01 0.344,0.26 10 false TX3- 5.729,0.354 6.125,0.615 0.396,0.26 10 false TX+ 5.74,0.771 6.135,1.031 0.396,0.26 10 false TX- 5.74,1.625 6.135,1.885 0.396,0.26 10 false +B 5.74,2.177 6.135,2.438 0.396,0.26 10 false ACC 5.74,2.75 6.135,3.01 0.396,0.26 10 false IG 5.729,3.313 6.125,3.573 0.396,0.26 10 false GND1 4.5,0.229 4.729,0.438 0.229,0.208 10 false 7 4.49,0.656 4.719,0.865 0.229,0.208 10 false 8 5.5,0.229 5.729,0.438 0.229,0.208 10 false 10 5.563,0.646 5.792,0.854 0.229,0.208 10 false 9 5.573,1.542 5.802,1.75 0.229,0.208 10 false 2 5.563,2.094 5.792,2.302 0.229,0.208 10 false 1 5.563,2.646 5.792,2.854 0.229,0.208 10 false 6 5.563,3.208 5.792,3.417 0.229,0.208 10 false 3

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Navigation Receiver Type)>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check that optional components (including associated wiring) which generate radio waves are not installed.

Result:
Result Proceed to
Optional components (including associated wiring) are installed. A
Optional components (including associated wiring) are not installed. B


HINT:
·

Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

·

This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.





A

2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

3.CHECK DTC
2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Remove optional components (including associated wiring).

NOTICE:

Do not remove optional components or associated wiring without the permission of the customer.



Result:
Proceed to
NEXT



NEXT

3.CHECK DTC
3.CHECK DTC
a.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Navigation Receiver Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

4.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU POWER SOURCE)
4.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU POWER SOURCE)
a.

Disconnect the F131 parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F131-3 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F131-2 (+B) - F131-3 (GND1) Always 11 to 14 V
F131-1 (ACC) - F131-3 (GND1) Engine switch on (ACC) 11 to 14 V
F131-6 (IG) - F131-3 (GND1) Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - PARKING ASSIST ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - PARKING ASSIST ECU)
a.

Disconnect the F117 navigation receiver assembly connector.


b.

Disconnect the F131 parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F117-7 (TX3+) - F131-10 (TX+) Always Below 1 Ω
F117-8 (TX3-) - F131-9 (TX-) Always Below 1 Ω
F117-7 (TX3+) or F131-10 (TX+) - Body ground Always 10 kΩ or higher
F117-8 (TX3-) or F131-9 (TX-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.REPLACE PARKING ASSIST ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE PARKING ASSIST ECU
a.

Replace the parking assist ECU with a new or known good one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST ECU>REMOVAL


b.

Clear the DTCs.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM(for Navigation Receiver Type)>DTC CHECK / CLEAR

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG