Home › Engine / Hybrid System › 2GR-FKS FUEL › FUEL INJECTOR(for Direct Injection) › from 2016.11
RM3160E _51 Engine / Hybrid System _060158 2GR-FKS FUEL _0298778 FUEL INJECTOR(for Direct Injection) A

2GR-FKS FUEL  FUEL INJECTOR(for Direct Injection)  REMOVAL  


PROCEDURE

Hide 23100X 1.REMOVE FUEL PUMP ASSEMBLY (for High Pressure)

Hide 23802B 2.REMOVE NO. 2 FUEL PIPE SUB-ASSEMBLY

a.
A368864

Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 2 fuel pipe sub-assembly.


b.

Remove the No. 2 fuel pipe sub-assembly from the fuel delivery pipe with sensor assembly LH and fuel delivery pipe RH.


Hide 23860 3.REMOVE FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY LH

a.
A393297

Disconnect the No. 6 engine wire connector and No. 7 engine wire connector.


b.
A393298

Disengage the 2 clamps to disconnect the No. 6 engine wire connector and No. 7 engine wire connector.


c.
A368866

Disconnect the fuel pressure sensor connector.


d.
A368867

Remove the bolt.


e.

Disengage the clamp to disconnect the No. 7 engine wire from the fuel delivery pipe with sensor assembly LH.


f.
A368868C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 2 bolts, 2 nuts and fuel delivery pipe with sensor assembly LH with the fuel injector assemblies.

NOTICE:
·

Make sure not to touch or strike the tips of the fuel injector assemblies.

·

Pull and remove the fuel delivery pipe with sensor assembly LH in a straight line without tilting it.




g.
A368871

Disconnect the 3 fuel injector assembly connectors.


Hide 23814E 4.REMOVE FUEL DELIVERY PIPE RH

a.
A394252

Remove the bolt.


b.

Disengage the clamp to disconnect the No. 6 engine wire from the fuel delivery pipe RH.


c.
A394253C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 2 bolts, 2 nuts and fuel delivery pipe RH with the fuel injector assemblies.

NOTICE:
·

Make sure not to touch or strike the tips of the fuel injector assemblies.

·

Pull and remove the fuel delivery pipe RH in a straight line without tilting it.




d.
A368872

Disconnect the 3 fuel injector assembly connectors.


Hide 23250 5.REMOVE FUEL INJECTOR ASSEMBLY

a.
A361016N01
2.333,2.75 3,3.052 0.667,0.302 10 true No. 2

Secure the fuel delivery pipe with sensor assembly LH and fuel delivery pipe RH in a vise between aluminum plates and pull out the 6 fuel injector assemblies.

NOTICE:
·

Pull and remove each fuel injector assembly in a straight line to avoid damaging the seal surface of the fuel delivery pipe with sensor assembly LH and fuel delivery pipe RH O-ring.

·

After removing the fuel injector assemblies, remove any O-rings, No. 1 fuel injector back-up rings and No. 3 fuel injector back-up rings remaining on the fuel delivery pipe with sensor assembly LH and fuel delivery pipe RH side.

·

Attach a tag or label with the corresponding cylinder number to each fuel injector assembly so that they can be installed to their original locations.




b.

Remove the nozzle holder clamp from each fuel injector assembly.


c.

Using needle nose pliers, remove the No. 3 fuel injector back-up ring from each fuel injector assembly.

NOTICE:

Do not damage the area that contacts the O-ring.



d.

Remove the O-ring and No. 1 fuel injector back-up ring from each fuel injector assembly.


e.

Remove the C-ring and injector vibration insulator from each fuel injector assembly.


Hide 23255A 6.REMOVE FUEL INJECTOR SEAL

a.
A361017

Using the tip of needle nose pliers, pinch and pull the fuel injector seal at several points to stretch it.

NOTICE:
·

Excessively pinching the fuel injector seal may damage the groove of the fuel injector assembly.

·

If a fuel injector assembly is dropped or the tip of the fuel injector assembly is struck, replace it with a new one.




b.

Remove the fuel injector seal from each fuel injector assembly.