Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2016.11
RM3160E _57 Power Source / Network _019704 NETWORKING _0095663 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Air Conditioning Amplifier Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Air Conditioning Amplifier Communication Stop Mode Either condition is met:
·

Communication stop for "Air Conditioning Amplifier" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Air Conditioning Amplifier Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Air conditioning amplifier assembly branch line or connector

·

Power source circuit of air conditioning amplifier assembly

·

Air conditioning amplifier assembly ground circuit

·

Air conditioning amplifier assembly



WIRING DIAGRAM

C408702E01
0.625,1.958 3.427,2.271 2.802,0.313 10 false No. 4 CAN Junction Connector 0.25,1.958 0.771,2.26 0.521,0.302 10 false F103 1.729,1.448 2.063,1.708 0.333,0.26 10 false 13 1.771,0.865 2.104,1.125 0.333,0.26 10 false 3 5.354,0.865 5.688,1.125 0.333,0.26 10 false 11 5.344,1.438 5.677,1.698 0.333,0.26 10 false 12 4.219,2.26 5.313,2.573 1.094,0.313 10 false A/C 5.375,2.333 5.781,2.646 0.406,0.313 10 false 21 5.396,3.156 5.729,3.417 0.333,0.26 10 false 1 4.115,3.094 5.156,3.396 1.042,0.302 10 false ECU-IG 2.302,2.448 4.063,2.802 1.76,0.354 10 false from Battery 1.708,3.281 3.25,3.698 1.542,0.417 10 false from IG1 NO. 2 Relay 5.365,3.99 5.698,4.25 0.333,0.26 10 false 14 5.667,4.125 6,4.385 0.333,0.26 10 false GND 5.677,3.292 6.01,3.552 0.333,0.26 10 false IG+ 5.677,2.479 6.01,2.74 0.333,0.26 10 false B 5.656,1 6.281,1.25 0.625,0.25 10 false CANH 5.667,1.573 6.344,1.885 0.677,0.313 10 false CANL 5.219,4.771 5.635,5.063 0.417,0.292 10 false F80 5.531,4.771 7.094,5.271 1.563,0.5 10 false Air Conditioning Amplifier Assembly 0.115,0.094 1.583,0.333 1.469,0.24 12 false for LHD:

C408702E02
0.625,1.958 3.427,2.271 2.802,0.313 10 false No. 3 CAN Junction Connector 0.25,1.958 0.771,2.26 0.521,0.302 10 false F102 1.729,1.448 2.063,1.708 0.333,0.26 10 false 13 1.771,0.865 2.104,1.125 0.333,0.26 10 false 3 5.354,0.865 5.688,1.125 0.333,0.26 10 false 11 5.344,1.438 5.677,1.698 0.333,0.26 10 false 12 4.219,2.26 5.313,2.573 1.094,0.313 10 false A/C 5.375,2.333 5.781,2.646 0.406,0.313 10 false 21 5.396,3.156 5.729,3.417 0.333,0.26 10 false 1 4.115,3.094 5.156,3.396 1.042,0.302 10 false ECU-IG 2.302,2.448 4.063,2.802 1.76,0.354 10 false from Battery 1.708,3.281 3.25,3.698 1.542,0.417 10 false from IG1 NO. 2 Relay 5.365,3.99 5.698,4.25 0.333,0.26 10 false 14 5.667,4.125 6,4.385 0.333,0.26 10 false GND 5.677,3.292 6.01,3.552 0.333,0.26 10 false IG+ 5.677,2.479 6.01,2.74 0.333,0.26 10 false B 5.656,1 6.281,1.25 0.625,0.25 10 false CANH 5.667,1.573 6.344,1.885 0.677,0.313 10 false CANL 5.219,4.771 5.635,5.063 0.417,0.292 10 false F80 5.531,4.771 7.094,5.271 1.563,0.5 10 false Air Conditioning Amplifier Assembly 0.115,0.094 1.583,0.333 1.469,0.24 12 false for RHD:

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait at least 20 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C292366C01
0.708,0.24 1.083,0.542 0.375,0.302 1.781,1.396 2.302,0.167 2.302,0.167 2.427,0.167 true 1.896,1.396 2.385,0.5 2.385,0.5 2.51,0.5 true 0.781,0.281 1.24,0.479 0.458,0.198 10 false F80 2.479,0.073 3.094,0.271 0.615,0.198 10 false CANH 2.573,0.406 3.188,0.604 0.615,0.198 10 false CANL 0.063,0.063 0.375,0.26 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Disconnect the F80 air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F80-11 (CANH) - F80-12 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C292366C03
0.708,0.24 1.083,0.542 0.375,0.302 2.135,1.396 2.625,0.5 2.625,0.5 2.75,0.5 true 0.781,0.281 1.24,0.479 0.458,0.198 10 false F80 2.802,0.406 3.188,0.615 0.385,0.208 10 false GND 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F80-14 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.
C292366C04
0.708,0.24 1.083,0.542 0.375,0.302 0.635,1.385 0.396,0.792 0.396,0.792 0.292,0.792 true 0.417,1.979 0.521,1.979 0.521,1.979 0.635,1.583 true 0.781,0.281 1.24,0.479 0.458,0.198 10 false F80 0.031,0.708 0.438,0.938 0.406,0.229 10 false IG+ 0.281,1.875 0.438,2.073 0.156,0.198 10 false B 0.052,0.042 0.365,0.24 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F80-1 (IG+) - Body ground Ignition switch ON 11 to 14 V
F80-21 (B) - Body ground Always 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)