Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2016.11
RM3160E _57 Power Source / Network _019704 NETWORKING _0095663 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Certification ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Certification ECU Communication Stop Mode Either condition is met:
·

Communication stop for "Certification (Smart)" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Certification ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Certification ECU (smart key ECU assembly) branch line or connector

·

Power source circuit of certification ECU (smart key ECU assembly)

·

Certification ECU (smart key ECU assembly) ground circuit

·

Certification ECU (smart key ECU assembly)



WIRING DIAGRAM

C363483E16
0.115,1.813 0.573,2.01 0.458,0.198 10 false F103 5.521,4.031 7.094,4.479 1.573,0.448 10 false Certification ECU (Smart Key ECU Assembly) 5.219,4.031 5.677,4.229 0.458,0.198 10 false F13 5.365,0.75 5.823,0.948 0.458,0.198 10 false 7 5.365,1.344 5.823,1.542 0.458,0.198 10 false 8 5.583,0.865 6.25,1.146 0.667,0.281 10 false CANH 1.656,1.344 2.115,1.542 0.458,0.198 10 false 17 1.698,0.75 2.156,0.948 0.458,0.198 10 false 7 5.583,1.458 6.271,1.792 0.688,0.333 10 false CANL 5.583,2.469 6.042,2.667 0.458,0.198 10 false +B 5.615,3.063 6.073,3.26 0.458,0.198 10 false E 0.5,1.813 2.74,2.104 2.24,0.292 10 false No. 4 CAN Junction Connector 5.302,2.958 5.76,3.156 0.458,0.198 10 false 11 5.292,2.354 5.75,2.552 0.458,0.198 10 false 10 4.021,2.302 5.156,2.552 1.135,0.25 10 false AM2 2.229,2.458 3.99,2.885 1.76,0.427 10 false from Battery 0.115,0.104 1.583,0.344 1.469,0.24 12 false for LHD:

C363483E17
0.115,1.813 0.573,2.01 0.458,0.198 10 false F102 5.521,4.031 7.094,4.479 1.573,0.448 10 false Certification ECU (Smart Key ECU Assembly) 5.219,4.031 5.677,4.229 0.458,0.198 10 false F13 5.365,0.75 5.823,0.948 0.458,0.198 10 false 7 5.365,1.344 5.823,1.542 0.458,0.198 10 false 8 5.583,0.865 6.25,1.146 0.667,0.281 10 false CANH 1.656,1.344 2.115,1.542 0.458,0.198 10 false 17 1.698,0.75 2.156,0.948 0.458,0.198 10 false 7 5.583,1.458 6.271,1.792 0.688,0.333 10 false CANL 5.583,2.469 6.042,2.667 0.458,0.198 10 false +B 5.615,3.063 6.073,3.26 0.458,0.198 10 false E 0.5,1.813 2.74,2.104 2.24,0.292 10 false No. 3 CAN Junction Connector 5.302,2.958 5.76,3.156 0.458,0.198 10 false 11 5.292,2.354 5.75,2.552 0.458,0.198 10 false 10 4.021,2.302 5.156,2.552 1.135,0.25 10 false AM2 2.229,2.458 3.99,2.885 1.76,0.427 10 false from Battery 0.135,0.094 1.604,0.333 1.469,0.24 12 false for RHD:

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait at least 20 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C279384C28
1.563,0.25 1.948,0.49 0.385,0.24 2.51,1.073 2.635,0.563 2.635,0.563 2.792,0.563 true 2.365,1.073 2.365,0.26 2.365,0.26 2.573,0.26 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 2.646,0.167 3.26,0.365 0.615,0.198 10 false CANH 2.844,0.469 3.323,0.667 0.479,0.198 10 false CANL 1.625,0.271 2.24,0.469 0.615,0.198 10 false F13
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Disconnect the F13 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F13-7 (CANH) - F13-8 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C279384C29
1.365,0.271 1.75,0.51 0.385,0.24 0.76,1.302 0.771,1.917 0.771,1.917 0.958,1.917 true 0.135,0.094 0.448,0.25 0.313,0.156 10 false *a 1.021,1.813 1.635,2.01 0.615,0.198 10 false E 1.438,0.292 2.052,0.49 0.615,0.198 10 false F13
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F13-11 (E) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.
C279384C30
1.365,0.271 1.75,0.51 0.385,0.24 2.813,1.073 2.781,0.281 2.781,0.281 2.542,0.281 true 0.135,0.094 0.448,0.25 0.313,0.156 10 false *a 2.323,0.188 2.938,0.385 0.615,0.198 10 false +B 1.438,0.292 2.052,0.49 0.615,0.198 10 false F13
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F13-10 (+B) - Body ground Always 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)