Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2016.11
RM3160E _57 Power Source / Network _019704 NETWORKING _0095663 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  AFS ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
AFS ECU Communication Stop Mode Either condition is met:
·

Communication stop for "Headlight swivel (AFS)" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "AFS ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Headlight leveling ECU assembly branch line or connector

·

Power source circuit of headlight leveling ECU assembly

·

Headlight leveling ECU assembly ground circuit

·

Headlight leveling ECU assembly



WIRING DIAGRAM

C363483E14
0.125,1.844 0.583,2.042 0.458,0.198 10 false F102 5.521,4.052 6.688,4.531 1.167,0.479 10 false Headlight Leveling ECU Assembly 5.24,4.052 5.698,4.25 0.458,0.198 10 false A67 5.375,0.75 5.833,0.948 0.458,0.198 10 false 6 5.375,1.344 5.833,1.542 0.458,0.198 10 false 7 5.583,0.865 6.302,1.188 0.719,0.323 10 false CANH 1.656,1.344 2.115,1.542 0.458,0.198 10 false 19 1.698,0.75 2.156,0.948 0.458,0.198 10 false 9 5.573,1.458 6.313,1.74 0.74,0.281 10 false CANL 5.594,2.469 6.052,2.667 0.458,0.198 10 false IG 5.594,3.063 6.146,3.385 0.552,0.323 10 false E1 0.5,1.844 2.74,2.135 2.24,0.292 10 false No. 3 CAN Junction Connector 5.385,2.958 5.844,3.156 0.458,0.198 10 false 9 5.385,2.354 5.844,2.552 0.458,0.198 10 false 1 3.938,2.302 5.073,2.552 1.135,0.25 10 false DSS-IG 1.635,2.458 3.396,2.885 1.76,0.427 10 false from IG1 NO. 3 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait at least 13 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (HEADLIGHT LEVELING ECU ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C281157C14
1.417,0.375 1.969,0.625 0.552,0.25 2.198,1.219 2.25,0.177 2.25,0.177 2.469,0.177 true 2.354,1.24 2.542,0.531 2.542,0.531 2.792,0.531 true 0.156,0.115 0.469,0.313 0.313,0.198 10 false *a 2.844,0.438 3.365,0.635 0.521,0.198 10 false CANL 2.51,0.094 3.125,0.292 0.615,0.198 10 false CANH 1.583,0.406 1.896,0.604 0.313,0.198 10 false A67
*a Front view of wire harness connector
(to Headlight Leveling ECU Assembly)


Disconnect the A67 headlight leveling ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A67-6 (CANH) - A67-7 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (HEADLIGHT LEVELING ECU ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C281157C15
1.448,0.313 1.958,0.563 0.51,0.25 2.615,1.24 2.656,0.438 2.656,0.438 2.844,0.438 true 0.135,0.094 0.448,0.292 0.313,0.198 10 false *a 2.906,0.365 3.219,0.563 0.313,0.198 10 false E1 1.573,0.354 1.885,0.552 0.313,0.198 10 false A67
*a Front view of wire harness connector
(to Headlight Leveling ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A67-9 (E1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.
C281157C16
1.448,0.313 1.958,0.563 0.51,0.25 0.698,1.24 0.76,0.542 0.76,0.542 0.917,0.542 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 0.979,0.448 1.292,0.646 0.313,0.198 10 false IG 1.583,0.354 1.896,0.552 0.313,0.198 10 false A67
*a Front view of wire harness connector
(to Headlight Leveling ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A67-1 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE HEADLIGHT LEVELING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)