Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2016.11
RM3160E _57 Power Source / Network _019704 NETWORKING _0095663 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Radio Receiver Assembly Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Radio Receiver Assembly Communication Stop Mode Either condition is met:
·

Communication stop for "Display and Navigation (AVN)" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Radio Receiver Assembly Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Radio and display receiver assembly branch line or connector

·

Power source circuit of radio and display receiver assembly

·

Radio and display receiver assembly ground circuit

·

Radio and display receiver assembly



WIRING DIAGRAM

C350991E17
0.542,1.865 2.802,2.083 2.26,0.219 10 false No. 7 CAN Junction Connector 0.177,1.865 0.698,2.125 0.521,0.26 10 false F135 5.344,1.271 5.688,1.49 0.344,0.219 10 false 10 5.396,0.708 5.74,0.927 0.344,0.219 10 false 9 2.354,2.26 3.885,2.531 1.531,0.271 10 false from Battery 5.323,0.969 5.792,1.25 0.469,0.281 10 false F71 5.323,1.5 5.865,1.833 0.542,0.333 10 false F71 5.323,2.302 5.802,2.604 0.479,0.302 10 false F69 5.323,2.948 5.854,3.281 0.531,0.333 10 false F69 5.323,3.583 5.927,3.927 0.604,0.344 10 false F71 5.323,4.26 5.802,4.583 0.479,0.323 10 false F69 1.635,0.833 1.979,1.052 0.344,0.219 10 false 5 1.604,1.375 1.948,1.594 0.344,0.219 10 false 16 5.396,2.063 5.74,2.281 0.344,0.219 10 false 4 5.396,2.708 5.74,2.927 0.344,0.219 10 false 3 5.396,3.354 5.74,3.573 0.344,0.219 10 false 1 5.406,4.021 5.75,4.24 0.344,0.219 10 false 7 5.354,4.938 7.052,5.417 1.698,0.479 10 false Radio and Display Receiver Assembly 2.104,2.927 3.635,3.198 1.531,0.271 10 false from ACC Relay 1.792,3.552 3.323,3.823 1.531,0.271 10 false from IG1 NO. 3 Relay 5.708,0.969 6.292,1.198 0.583,0.229 10 false CANH 5.708,1.5 6.292,1.729 0.583,0.229 10 false CANL 5.719,3.583 6.302,3.813 0.583,0.229 10 false IG 5.708,2.948 6.292,3.177 0.583,0.229 10 false ACC1 5.708,2.292 6.292,2.521 0.583,0.229 10 false +B1 5.698,4.26 6.281,4.49 0.583,0.229 10 false GND1 4.104,3.375 5.229,3.677 1.125,0.302 10 false IG1 NO. 3 4.135,2.76 5.26,3.063 1.125,0.302 10 false ECU-ACC 4.198,2.104 4.969,2.406 0.771,0.302 10 false RADIO

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait at least 31 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (RADIO AND DISPLAY RECEIVER ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C287273C08
0.229,1.063 0.656,1.313 0.427,0.25 1.885,1.135 1.875,0.417 1.875,0.417 1.615,0.417 true 2.01,1.135 1.99,0.396 1.99,0.396 2.24,0.396 true 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 2.292,0.302 2.906,0.5 0.615,0.198 10 false CANL 1.188,0.313 1.802,0.51 0.615,0.198 10 false CANH 0.302,1.094 0.615,1.292 0.313,0.198 10 false F71
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the F71 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F71-9 (CANH) - F71-10 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C287274C12
1.438,0.208 1.885,0.5 0.448,0.292 1.135,1.99 1.396,1.99 1.396,1.99 1.552,1.625 true 0.125,0.146 0.438,0.344 0.313,0.198 10 false *a 1.542,0.25 1.854,0.448 0.313,0.198 10 false F69 0.74,1.896 1.188,2.073 0.448,0.177 10 false GND1
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the F69 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F69-7 (GND1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) battery terminal.


d.
C290810C13
1.479,0.25 1.927,0.583 0.448,0.333 1.49,2.281 1.938,2.615 0.448,0.333 2.063,1.375 2.365,0.667 2.365,0.667 2.49,0.667 true 2.302,1.385 2.5,0.927 2.5,0.927 2.615,0.927 true 0.958,3.417 0.823,2.823 0.823,2.823 0.708,2.823 true 0.063,0.083 0.375,0.281 0.313,0.198 10 false *a 1.594,0.302 1.906,0.5 0.313,0.198 10 false F69 1.583,2.333 2.042,2.531 0.458,0.198 10 false F71 2.552,0.573 3.167,0.771 0.615,0.198 10 false ACC1 2.677,0.823 3.135,1.021 0.458,0.198 10 false +B1 0.51,2.729 0.823,2.927 0.313,0.198 10 false IG
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F69-3 (ACC1) - Body ground Ignition switch ACC 11 to 14 V
F69-4 (+B1) - Body ground Always 11 to 14 V
F71-1 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)