Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2016.11
RM3160E _57 Power Source / Network _019704 NETWORKING _0095663 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Parking Assist ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Parking Assist ECU Communication Stop Mode Either condition is met:
·

Communication stop for "Panoramic View Monitor" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Parking Assist ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Parking assist ECU branch line or connector

·

Power source circuit of parking assist ECU

·

Parking assist ECU ground circuit

·

Parking assist ECU



WIRING DIAGRAM

C361495E10
0.25,1.969 0.708,2.167 0.458,0.198 10 false F134 0.615,1.969 2.802,2.25 2.188,0.281 10 false No. 1 CAN Junction Connector 1.74,1.438 2.198,1.635 0.458,0.198 10 false 2 1.719,0.844 2.177,1.042 0.458,0.198 10 false 1 5.333,0.865 5.792,1.063 0.458,0.198 10 false 12 5.344,1.438 5.802,1.635 0.458,0.198 10 false 13 5.656,0.969 6.177,1.24 0.521,0.271 10 false CANH 5.656,1.563 6.146,1.823 0.49,0.26 10 false CANL 3.865,2.281 5.083,2.604 1.219,0.323 10 false MPX-B NO. 3 4.01,2.823 4.927,3.146 0.917,0.323 10 false ECU-ACC 4,3.354 5.177,3.635 1.177,0.281 10 false IG1 NO. 3 5.396,2.333 5.854,2.531 0.458,0.198 10 false 2 5.406,2.885 5.865,3.083 0.458,0.198 10 false 1 5.406,3.417 5.865,3.615 0.458,0.198 10 false 6 5.417,3.99 5.875,4.188 0.458,0.198 10 false 3 5.667,4.125 6.323,4.458 0.656,0.333 10 false GND1 5.656,3.531 6.115,3.729 0.458,0.198 10 false IG 5.656,3.01 6.115,3.208 0.458,0.198 10 false ACC 5.656,2.458 6.115,2.656 0.458,0.198 10 false +B 5.188,4.823 5.646,5.021 0.458,0.198 10 false F131 5.542,4.823 7.094,5.198 1.552,0.375 10 false Parking Assist ECU 1.708,3.521 3.24,3.875 1.531,0.354 10 false from IG1 NO. 3 Relay 2.24,2.438 3.719,2.823 1.479,0.385 10 false from Battery 2.01,2.99 3.542,3.344 1.531,0.354 10 false from ACC Relay

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for at least 20 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (PARKING ASSIST ECU BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C306889C29
0.115,1.208 0.563,1.51 0.448,0.302 2.458,0.208 2.073,0.208 2.073,0.208 2.073,1.323 true 1.688,0.208 1.969,0.208 1.969,0.208 1.969,1.323 true 0.104,0.052 0.417,0.208 0.313,0.156 10 false *a 0.188,1.281 0.646,1.521 0.458,0.24 10 false F131 1.24,0.125 1.854,0.323 0.615,0.198 10 false CANH 2.542,0.125 3.156,0.323 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to Parking Assist ECU)


Disconnect the F131 parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F131-12 (CANH) - F131-13 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (PARKING ASSIST ECU)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C306889C30
0.115,1.208 0.573,1.51 0.458,0.302 2.469,0.49 2.25,0.49 2.25,0.49 2.25,1.115 true 1.052,1.406 1.052,2.01 1.052,2.01 1.219,2.01 true 0.583,0.75 0.75,0.75 0.75,0.75 0.938,1.125 true 1,0.479 1.25,0.479 1.25,0.479 1.25,1.083 true 0.104,0.052 0.417,0.208 0.313,0.156 10 false *a 0.188,1.271 0.604,1.49 0.417,0.219 10 false F131 0.698,0.417 0.958,0.583 0.26,0.167 10 false +B 2.531,0.396 2.948,0.563 0.417,0.167 10 false GND1 0.208,0.667 0.625,0.833 0.417,0.167 10 false ACC 1.302,1.917 1.917,2.115 0.615,0.198 10 false IG
*a Front view of wire harness connector
(to Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F131-3 (GND1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F131-2 (+B) - Body ground Always 11 to 14 V
F131-1 (ACC) - Body ground Ignition switch ACC 11 to 14 V
F131-6 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)