Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2016.11
RM3160E _57 Power Source / Network _019704 NETWORKING _0095663 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Rear Television Camera Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Rear Television Camera Communication Stop Mode Either condition is met:
·

Communication stop for "Parking Assist Monitor System" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Rear Television Camera Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

Television camera assembly branch line or connector

·

Power source circuit of television camera assembly

·

Television camera assembly ground circuit

·

Television camera assembly



WIRING DIAGRAM

C350494E08
0.625,1.844 2.792,2.271 2.167,0.427 10 false No. 2 CAN Junction Connector 0.344,2.906 3.063,3.344 2.719,0.438 10 false from Radio and Display Receiver Assembly 0.49,3.656 3.052,4.208 2.563,0.552 10 false to Radio and Display Receiver Assembly 4.969,4.604 5.469,4.875 0.5,0.271 10 false X13 5.26,4.604 7.104,4.917 1.844,0.313 10 false Television Camera Assembly 5.417,0.771 5.573,0.969 0.156,0.198 10 false 4 5.427,1.302 5.583,1.5 0.156,0.198 10 false 1 5.417,2.781 5.573,2.979 0.156,0.198 10 false 6 5.417,3.542 5.573,3.74 0.156,0.198 10 false 5 5.625,0.875 6.24,1.073 0.615,0.198 10 false CANH 5.625,1.427 6.24,1.625 0.615,0.198 10 false CANL 5.625,2.906 6.083,3.104 0.458,0.198 10 false CB+ 5.625,3.646 6.24,3.844 0.615,0.198 10 false CGND 1.708,0.74 1.865,0.938 0.156,0.198 10 false 1 1.719,1.302 1.875,1.5 0.156,0.198 10 false 2 0.281,1.844 0.74,2.042 0.458,0.198 10 false M39

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for at least 14 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (TELEVISION CAMERA ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C346954C19
1.5,0.146 1.906,0.385 0.406,0.24 1.344,1.938 1.51,1.938 1.51,1.938 1.51,1.427 true 1.365,0.469 1.51,0.469 1.51,0.469 1.51,1.083 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 1.583,0.177 2.052,0.458 0.469,0.281 10 false X13 0.938,1.885 1.427,2.052 0.49,0.167 10 false CANH 0.958,0.427 1.448,0.594 0.49,0.167 10 false CANL
*a Front view of wire harness connector
(to Television Camera Assembly)


Disconnect the X13 television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X13-4 (CANH) - X13-1 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (TELEVISION CAMERA ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C346954C20
1.5,0.146 1.906,0.396 0.406,0.25 1.563,1.927 1.729,1.927 1.729,1.927 1.729,1.417 true 2.115,1.927 1.906,1.927 1.906,1.927 1.906,1.417 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 1.594,0.188 2.042,0.458 0.448,0.271 10 false X13 1.167,1.844 1.656,2.01 0.49,0.167 10 false CGND 2.156,1.865 2.646,2.031 0.49,0.167 10 false CB+
*a Front view of wire harness connector
(to Television Camera Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
X13-5 (CGND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
X13-6 (CB+) - Body ground Ignition switch ACC 5.5 to 7.05 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)