Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2016.11
RM3160E _59 Vehicle Exterior _019722 LIGHTING (EXT) _0103403 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Taillight Relay Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the operation of the TAIL relay.

WIRING DIAGRAM

E360278E01
0.323,0.542 2.156,0.74 1.833,0.198 10 false from Battery 0.24,0.958 2.073,1.156 1.833,0.198 10 false from ALT Fuse 1.958,1.115 2.573,1.354 0.615,0.24 10 false J/B-ALT 2.073,0.698 2.688,0.938 0.615,0.24 10 false ALT 2.5,0.865 3.115,1.104 0.615,0.24 10 false *2 2.5,0.448 3.115,0.688 0.615,0.24 10 false *1 3.271,0.563 3.885,0.802 0.615,0.24 10 false 4K 3.323,0.354 3.938,0.594 0.615,0.24 10 false 1 4.521,1.229 5.135,1.469 0.615,0.24 10 false TAIL 5.271,1.094 5.885,1.333 0.615,0.24 10 false TAIL 6.031,0.458 6.646,0.698 0.615,0.24 10 false 14 6.302,0.552 6.917,0.792 0.615,0.24 10 false TRLY 3.271,1.531 3.885,1.771 0.615,0.24 10 false 4H 3.281,1.333 3.896,1.573 0.615,0.24 10 false 16 3.271,2.188 3.885,2.427 0.615,0.24 10 false 4H 3.292,1.99 3.906,2.229 0.615,0.24 10 false 17 3.292,2.875 3.906,3.115 0.615,0.24 10 false 4F 3.323,2.667 3.938,2.906 0.615,0.24 10 false 4 5.469,3.854 7.135,4.406 1.667,0.552 10 false Main Body ECU (Multiplex Network Body ECU) 5.469,3.698 5.771,3.969 0.302,0.271 10 false MB 3.531,3.229 6.365,3.635 2.833,0.406 10 false Instrument Panel Junction Block Assembly 1.479,2.865 2.719,3.167 1.24,0.302 10 false to Clearance Lights 0.792,2.125 2.698,2.573 1.906,0.448 10 false to Taillights (Rear Combination Light Assemblies) 0.198,1.49 2.688,1.958 2.49,0.469 10 false to Taillights (Rear Light Assemblies) and License Plate Lights 0.385,3.802 1.625,4.104 1.24,0.302 10 false *1: for 1AR-FE 0.385,4.073 1.625,4.375 1.24,0.302 10 false *2: for 2GR-FKS

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*

*: w/ Smart Entry and Start System


·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: for LHD




PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Taillight Relay Taillight relay OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Taillight Relay
50004 123 13
OK:

Taillight relay operates. (Taillights illuminate.)



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 4K instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4K-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E259753C04
0.802,0.385 1.104,0.604 0.302,0.219 3.042,0.365 3.344,0.583 0.302,0.219 5.792,0.385 6.094,0.604 0.302,0.219 3.396,2.198 3.729,2.448 0.333,0.25 3.115,3.26 3.281,2.885 false 0.865,0.417 1.177,0.615 0.313,0.198 10 false 4K 3.125,0.396 3.438,0.594 0.313,0.198 10 false 4F 5.875,0.427 6.188,0.625 0.313,0.198 10 false 4H 3.479,2.25 3.792,2.448 0.313,0.198 10 false MB 2.938,3.313 3.552,3.51 0.615,0.198 10 false TRLY 0.188,0.156 0.5,0.354 0.313,0.198 10 false *a
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Connect a positive (+) lead from the battery to terminal 4K-1.


d.

Connect a negative (-) lead from the battery to terminal MB-14 (TRLY).


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4H-17 - Battery negative (-) terminal Always 11 to 14 V
4F-4 - Battery negative (-) terminal Always 11 to 14 V
4H-16 - Battery negative (-) terminal Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY