DATA LIST
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
To display the list box, press the pull down menu button next to Primary. Then select a measurement group.
When you select a measurement group, the ECU data belonging to that group is displayed.
Measurement Group List / Description
All Data / All data
Primary / -
Engine Control / Engine control system related data
Gas General / -
Gas AF Control / Air fuel ratio control system related data
Gas AF O2 Sensor / Air fuel ratio sensor and heated oxygen sensor related data
Gas Throttle / Gasoline throttle system related data
Gas Intake Control / Intake control system related data
Gas Valve Control / Valve control system related data
Gas Misfire / "Misfire" related data
Gas Starting / "Difficult to start" related data
Gas Rough Idle / "Rough idle" related data
Gas Evaporative / Evaporative system related data
Gas CAT Converter / Catalyst converter related data
Check Mode / Check mode related data
Monitor Status / Monitor status related data
Ignition / Ignition system related data
Charging Control / Charging control system related data
Compression / Data used during "Check the Cylinder Compression" Active Test
AT / Automatic transmission system related data
Vehicle Information / Vehicle information
According to the display on the GTS, read the Data List.
The title used for each group of Data List items in this repair manual does not appear on the GTS. However, the name in parentheses after the title, which is a Measurement Group, does appear on the GTS. When the name shown in parentheses is selected on the GTS, all the Data List items listed for that group will be displayed.
"Result of real-vehicle check" is the assessment of one vehicle. Use it only for reference.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Vehicle Speed | Vehicle Speed | Min.: 0 km/h (0 MPH)
Max.: 255 km/h (158 MPH) |
Actual vehicle speed | - |
| Engine Speed | Engine speed | Min.: 0 rpm
Max.: 16383.75 rpm |
600 to 700 rpm: Idling | When the crankshaft position sensor is malfunctioning, "Engine Speed" is approximately 0 rpm or varies greatly from the actual engine speed. |
| MAF | Airflow rate from mass air flow meter sub-assembly | Min.: 0 gm/sec
Max.: 655.35 gm/sec |
·
1.0 to 3.0 gm/sec: Idling ·
8.0 to 22.0 gm/sec: 3000 rpm (without load) |
This is the intake air amount from the mass air flow meter sub-assembly. |
| Coolant Temp | Coolant temperature | Min.: -40°C (-40°F)
Max.: 140°C (284°F) |
75 to 100°C (167 to 212°F): After warming up | This is the engine coolant temperature.
|
| Throttle Motor DUTY | Throttle actuator | Min.: 0%
Max.: 100% |
10 to 22%: Idling | This is the output duty ratio of the throttle actuator drive circuit. |
| Starter Signal | Starter signal | Open or Close | - | - |
| Neutral Position SW Signal | PNP switch status | ON or OFF | ·
ON: Shift lever in P or N ·
OFF: Shift lever not in P or N |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
|
| Stop Light Switch | Stop light switch status | ON or OFF | Brake pedal is
·
ON: Depressed ·
OFF: Released |
- |
| A/C Signal | A/C switch status | ON or OFF | ON: A/C on | - |
| Closed Throttle Position SW | Closed throttle position switch status | ON or OFF | ·
ON: Throttle fully closed ·
OFF: Throttle open |
- |
| SPD (NT) | Input turbine speed | Min.: 0 rpm
Max.: 12750 rpm |
Lock-up is
·
ON (After warming up the engine): Input turbine speed (NT) is equal to engine speed ·
OFF (idling with shift lever in N): Input turbine speed (NT) is nearly equal to engine speed |
Data is displayed in increments of 50 rpm |
| SPD (NC) | Counter gear speed | Min.: 0 rpm
Max.: 12750 rpm |
- | Data is displayed in increments of 50 rpm |
| Shift SW Status (P Range) | PNP switch status | ON or OFF | ·
ON: Shift lever in P ·
OFF: Shift lever not in P |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
|
| Shift SW Status (R Range) | PNP switch status | ON or OFF | ·
ON: Shift lever in R ·
OFF: Shift lever not in R |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
|
| Shift SW Status (N Range) | PNP switch status | ON or OFF | ·
ON: Shift lever in N ·
OFF: Shift lever not in N |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
|
| Shift SW Status (N,P Range) Supported | PNP switch status | Unsupp or Supp | Supp | - |
| Shift SW Status (N,P Range) | PNP switch status | ON or OFF | ·
OFF: Shift lever in N or P ·
ON: Shift lever not in N or P |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
|
| Sports Shift Up SW | Sport shift up switch status | ON or OFF | ·
ON: Shift lever held in "+" (up-shift) ·
OFF: Shift lever not held in "+" (up-shift) |
- |
| Sports Shift Down SW | Sport shift down switch status | ON or OFF | ·
ON: Shift lever held in "-" (down-shift) ·
OFF: Shift lever not held "-" (down-shift) |
- |
| Sports Mode Selection SW | Sport mode select switch status | ON or OFF | ·
ON: Shift lever in S, "+" or "-" ·
OFF: Shift lever not in S, "+" or "-" |
- |
| Shift SW Status (D Range) | PNP switch status | ON or OFF | ·
ON: Shift lever in D or S ·
OFF: Shift lever not in D or S |
When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the park/neutral position switch or shift cable may be incorrect.
|
| A/T Oil Temperature 1 | ATF temp. sensor value | Min.: -40 C (-40 F)
Max.: 215 C (419 F) |
·
After stall test; Approx. 80°C (176°F) ·
Equal to ambient temperature when cold soak |
If the value is "-40°C (-40°F)" or "150°C (302°F)", ATF temp. sensor circuit is open or shorted. |
| NT Sensor Voltage | Input speed sensor NT output voltage | Min.: 0.000 V
Max.: 5.000 V |
0.1 to 1.9 V | - |
| NC Sensor Voltage | Output speed sensor NC output voltage | Min.: 0.000 V
Max.: 5.000 V |
0.1 to 1.9 V | - |
| Lock Up | Lock up | ON or OFF | ·
ON: Lock-up operating ·
OFF: Lock-up not operating |
- |
| Shift Status | ECM gear shift command | 1st, 2nd, 3rd, 4th, 5th or 6th | Same as actual gear | - |
| SLT Solenoid Status | Shift solenoid SLT status | ON or OFF | ·
ON: Shift solenoid SLT operating ·
OFF: Shift solenoid SLT not operating |
- |
| SLU Solenoid Status | Shift Solenoid SLU Status | ON or OFF | ·
ON: Shift solenoid SLU operating ·
OFF: Shift solenoid SLU not operating |
- |
| SL Solenoid Status | Shift Solenoid SL Status | ON or OFF | ·
ON: Shift solenoid SL operating ·
OFF: Shift solenoid SL not operating |
- |
| Snow or 2nd Start Mode | Snow mode status | ON or OFF | - | - |
*: Refer to DTC P0705.
Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>P0705
ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Connect the TC and TE1 | Connects and disconnects TC and TE1.
(changes to the fluid temperature detection mode) |
ON/OFF | The MIL will not blink when "Connect the TC and TE1 / ON" is selected. |
| Activate the Solenoid (SLU) | Operates shift solenoid SLU | ON/OFF | [Vehicle Condition]
·
Engine stopped ·
Shift lever in P or N |
| Activate the Solenoid (SLT) | Operates shift solenoid SLT to raise the line pressure. | ON/OFF
|
[Vehicle Condition]
·
Vehicle Stopped ·
IDL: ON |
| Activate the Lock Up | Controls the shift solenoid SLU and SL to set the automatic transaxle to the lock-up condition. | ON/OFF | Can be used to check SLU and SL solenoid operation.
[Vehicle Condition] ·
Throttle valve opening angle: Less than 20% ·
Vehicle speed:60 km/h (37 mph) or more, and 6th gear |
| Activate the Solenoid (SL) | Operates shift solenoid SL | ON/OFF | [Vehicle Condition]
·
Engine stopped ·
Shift lever in P or N |
| Control the Shift Position | Operates the shift solenoid valves to allow gears to be selected manually. | ·
Press "→" button: Upshift occurs ·
Press "←" button: Downshift occurs |
Can be used to check the operation of the shift solenoid valves.
Upshifts and downshifts should be performed consecutively. A 10-second interval is required between gear changes. Do not downshift at high speeds. Doing so will damage the automatic transaxle. [Vehicle Condition] 50 km/h (31 mph) or less |
| Activate the Solenoid (SL1) | Operates shift solenoid SL1 | ON/OFF | [Vehicle Condition]
·
Engine stopped ·
Shift lever in P or N |
| Activate the Solenoid (SL2) | Operates shift solenoid SL2 | ON/OFF | [Vehicle Condition]
·
Engine stopped ·
Shift lever in P or N |
| Activate the Solenoid (SL3) | Operates shift solenoid SL3 | ON/OFF | [Vehicle Condition]
·
Engine stopped ·
Shift lever in P or N |
| Activate the Solenoid (SL4) | Operates shift solenoid SL4 | ON/OFF | [Vehicle Condition]
·
Engine stopped ·
Shift lever in P or N |
The "Activate the solenoid (SLT)" Active Test is performed to allow confirmation that the line pressure changes. The line pressure changes are confirmed using the same SST that is used for the Hydraulic Test.
Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>HYDRAULIC TEST
Note that the pressure readings for the Active Test and Hydraulic Test are different.