Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › SFI SYSTEM › from 2016.11
RM3160E _51 Engine / Hybrid System _060156 2GR-FKS ENGINE CONTROL _0299070 SFI SYSTEM C

2GR-FKS ENGINE CONTROL  SFI SYSTEM  P012011  Throttle / Pedal Position Sensor / Switch "A" Circuit Short to Ground  P012015  Throttle / Pedal Position Sensor / Switch "A" Circuit Short to Battery or Open  P01201C  Throttle / Pedal Position Sensor / Switch "A" Circuit Voltage Out of Range  P022011  Throttle/Pedal Position Sensor/Switch "B" Circuit Short to Ground  P022015  Throttle/Pedal Position Sensor/Switch "B" Circuit Short to Battery or Open  P21352B  Throttle/Pedal Position Sensor/Switch "A"/"B" Voltage Correlation Signal Cross Coupled  


DESCRIPTION

HINT:

These DTCs relate to the throttle position sensor.


The throttle position sensor is mounted on the throttle body with motor assembly and detects the opening angle of the throttle valve. This sensor is a non-contact type sensor. It uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds.

The throttle position sensor has 2 sensor circuits, VTA1 and VTA2 each of which transmits a signal. VTA1 is used to detect the throttle valve angle and VTA2 is used to detect malfunctions in VTA1. The sensor signal voltages vary between 0 V and 5 V in proportion to the throttle valve opening angle, and are transmitted to the VTA1 and VTA2 terminals of the ECM.

As the valve closes, the sensor output voltage decreases and as the valve opens, the sensor output voltage increases. The ECM calculates the throttle valve opening angle according to these signals and controls the throttle actuator in response to driver inputs. These signals are also used in calculations such as air fuel ratio correction, power increase correction and fuel-cut control.

A293043E57
4.188,1.063 4.385,0.583 4.385,0.583 4.542,0.583 false 5.74,1.51 5.51,0.281 5.51,0.281 5.229,0.281 false 5.323,1.875 5.802,2.323 false 4.979,2.229 5.313,2.531 false 1.021,2.583 0.927,1.781 0.927,1.781 0.792,1.781 false 1.49,1.219 1.063,2.188 false 0.969,2.958 0.583,3.563 false 1.073,3.344 1.552,3.75 false 4.677,1.469 4.896,1.656 false 1.573,1.052 2.49,1.25 0.917,0.198 10 false Magnet 0.24,1.708 1.156,1.906 0.917,0.198 10 false IC No. 1 0.323,3.656 1.24,3.854 0.917,0.198 10 false IC No. 2 1.594,3.74 2.51,3.938 0.917,0.198 10 false Magnet 0.104,4.115 1.979,4.406 1.875,0.292 10 false Throttle Position Sensor 0.146,4.51 2.021,4.802 1.875,0.292 10 false Note: 0.167,4.708 3.375,5.333 3.208,0.625 10 false The throttle valve opening angle transmitted through sensor terminal VTA1 is expressed as a percentage. 0.167,5.417 3.365,5.635 3.198,0.219 10 false Between 10% and 22%: Throttle valve fully closed 0.167,5.75 3.365,5.969 3.198,0.219 10 false Between 64% and 96%: Throttle valve fully open 0.167,6.115 3.365,6.333 3.198,0.219 10 false Approximately 19.4%: Fail safe angle (7°) 3.531,0.188 5.271,0.479 1.74,0.292 10 false Line indicating VTA2 x 0.8 2.5,0.677 4.24,0.969 1.74,0.292 10 false Sensor Output Voltage (V) 4.604,0.51 5.604,0.865 1,0.354 10 false Fail-safe Angle 5.385,2.531 5.781,2.938 0.396,0.406 10 false VTA1 3.896,3.51 6.094,3.844 2.198,0.333 10 false Throttle Valve Opening Angle (°) 3.875,3.896 6.01,4.115 2.135,0.219 10 false *: During fail-safe control 3.719,4.76 5.917,5.094 2.198,0.333 10 false Characteristics of sensor output: 3.75,5.198 7.156,5.51 3.406,0.313 10 false VTA2 x 0.8 is approximately equal to VTA1 + 1.11 V 5.823,2.375 6.427,2.75 0.604,0.375 10 false 1.11 V 4.281,1.365 4.677,1.771 0.396,0.406 10 false VTA2 3.75,0.99 4.01,1.396 0.26,0.406 10 false 5.0 3.667,1.188 4,1.594 0.333,0.406 10 false 4.65 3.75,1.917 4.26,2.146 0.51,0.229 10 false 2.6* 3.688,2.063 4.021,2.469 0.333,0.406 10 false 2.25 3.667,2.438 4.25,2.656 0.583,0.219 10 false 0.97* 3.656,2.604 3.99,3.01 0.333,0.406 10 false 0.69 4.156,2.854 4.49,3.26 0.333,0.406 10 false 7 3.979,3.271 4.313,3.677 0.333,0.406 10 false 0 6.271,3.292 6.604,3.698 0.333,0.406 10 false 86 1.688,2.771 2.083,3.177 0.396,0.406 10 false VTA2 1.677,2.385 2.073,2.792 0.396,0.406 10 false VTA1 1.677,2.021 2.26,2.375 0.583,0.354 10 false VCTA 1.708,3.125 2.104,3.531 0.396,0.406 10 false ETA 4.698,3.188 5.719,3.406 1.021,0.219 10 false Usable Range 2.417,4.073 3.333,4.271 0.917,0.198 10 false ECM

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P012011 Throttle / Pedal Position Sensor / Switch "A" Circuit Short to Ground The output voltage of VTA1 is less than 0.56 V for 2 seconds or more (1 trip detection logic).
·

Throttle position sensor (throttle body with motor assembly)

·

Short in VTA1 circuit

·

Open in VCTA circuit

·

ECM


Comes on DTC stored SAE Code: P0122
P012015 Throttle / Pedal Position Sensor / Switch "A" Circuit Short to Battery or Open The output voltage of VTA1 is higher than 4.535 V for 2 seconds or more (1 trip detection logic).
·

Throttle position sensor (throttle body with motor assembly)

·

Open in VTA1 circuit

·

Open in ETA circuit

·

Short between VCTA and VTA1 circuits

·

ECM


Comes on DTC stored SAE Code: P0123
P01201C Throttle / Pedal Position Sensor / Switch "A" Circuit Voltage Out of Range The difference between the output voltage of VTA1 and VTA2 is less than 0.8 V, or higher than 1.6 V for 2 seconds or more (1 trip detection logic).
·

Throttle position sensor (throttle body with motor assembly)

·

Throttle position sensor circuit

·

ECM


Comes on DTC stored SAE Code: P0121
P022011 Throttle/Pedal Position Sensor/Switch "B" Circuit Short to Ground The output voltage of VTA2 is less than 2.05 V for 2 seconds or more (1 trip detection logic).
·

Throttle position sensor (throttle body with motor assembly)

·

Short in VTA2 circuit

·

Open in VCTA circuit

·

ECM


Comes on DTC stored SAE Code: P0222
P022015 Throttle/Pedal Position Sensor/Switch "B" Circuit Short to Battery or Open The output voltage of VTA2 is higher than 4.75 V, and VTA1 is less than 2.367 V for 2 seconds or more (1 trip detection logic).
·

Throttle position sensor (throttle body with motor assembly)

·

Open in VTA2 circuit

·

Short between VCTA and VTA2 circuits

·

ECM


Comes on DTC stored SAE Code: P0223
P21352B Throttle/Pedal Position Sensor/Switch "A"/"B" Voltage Correlation Signal Cross Coupled The difference between the output voltages of VTA1 and VTA2 is 0.02 V or less for 2 seconds or more (1 trip detection logic).
·

Throttle position sensor (throttle body with motor assembly)

·

Short between VTA1 and VTA2 circuits

·

Open in ETA circuit

·

ECM


Comes on DTC stored SAE Code: P2135

HINT:
·

When any of these DTCs are output, check the throttle valve opening angle using the GTS. Enter the following menus: Powertrain / Engine / Data List / Throttle Position Sensor No.1 Voltage and Throttle Position Sensor No.2 Voltage.

·

Throttle Position Sensor No.1 Voltage is the VTA1 signal, and Throttle Position Sensor No.2 Voltage is the VTA2 signal.

Reference (Normal Condition):
GTS Display Accelerator Pedal Fully Released Accelerator Pedal Fully Depressed (Engine Running)
Throttle Position Sensor No.1 Voltage 0.6 to 1.1 V 3.2 to 4.8 V
Throttle Position Sensor No.2 Voltage 2.1 to 3.1 V 4.6 to 4.98 V




MONITOR DESCRIPTION

The ECM uses the throttle position sensor to monitor the throttle valve opening angle. There are several checks that the ECM performs to confirm the proper operation of the throttle position sensor.

P012011, P012015, P022011, P022015 and P21352B:
·

A specific voltage difference is expected between the sensor terminals, VTA1 and VTA2, for each throttle valve opening angle. If the difference between VTA1 and VTA2 is incorrect, the ECM interprets this as a malfunction in the sensor circuit, and stores a DTC.

·

VTA1 and VTA2 each have a specific voltage range. If VTA1 or VTA2 is outside the normal operating range, the ECM interprets this as a malfunction in the sensor circuit, and stores a DTC.

·

VTA1 and VTA2 should never be close to the same voltage level. If VTA1 is within 0.02 V of VTA2, the ECM determines that there is a short circuit in the sensor circuit, and stores a DTC.


P01201C:

This sensor transmits two signals: VTA1 and VTA2. VTA1 is used to detect the throttle opening angle and VTA2 is used to detect malfunctions in VTA1. The ECM performs several checks to confirm the proper operation of the throttle position sensor and VTA1.

For each throttle opening angle, a specific voltage difference is expected between the outputs of VTA1 and VTA2. If the output voltage difference between the two signals deviates from the normal operating range, the ECM interprets this as a malfunction in the throttle position sensor. In this case the ECM will illuminate the MIL and store this DTC.


MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A399792E01
2.594,2 2.313,1.354 2.313,1.354 2.479,1.354 false 3.667,1.448 3.219,0.563 3.219,0.563 3.406,0.563 false 4.906,1.99 5.188,1.115 5.188,1.115 5.333,1.115 false 1.26,1.854 1.948,2.135 0.688,0.281 10 false Idling 0.469,2.167 1.74,2.448 1.271,0.281 10 false Ignition Switch ON 2.104,2.031 2.438,2.313 0.333,0.281 10 false [A] 3.865,1.771 4.24,2.063 0.375,0.292 10 false [B] 4.698,1.792 5.042,2.083 0.344,0.292 10 false [C] 5.042,2.969 5.396,3.292 0.354,0.323 10 false [D] 2.521,1.281 3.24,1.573 0.719,0.292 10 false Released 3.448,0.479 4.427,0.771 0.979,0.292 10 false Depressed 5.365,1.031 6.219,1.385 0.854,0.354 10 false Released 4.354,2.656 5.01,3.104 0.656,0.448 10 false 2 seconds or more

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine.

7.

With the vehicle stationary, fully depress and release the accelerator pedal [B].

8.

Idle the engine for 2 seconds or more [C].

9.

Enter the following menus: Powertrain / Engine / Trouble Codes [D].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P012011, P012015, P01201C, P022011, P022015 or P21352B.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [D] again.




FAIL-SAFE

When any of these DTCs or other DTCs relating to Electronic Throttle Control System (ETCS) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a 7° throttle valve opening angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal angle, to allow the vehicle to continue running at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

A282199E54
2.083,1.917 2.198,2.063 0.115,0.146 10 false 5 4.385,1.917 4.635,2.083 0.25,0.167 10 false 121 4.708,1.917 5.115,2.073 0.406,0.156 10 false VCTA 1.781,1.99 2.146,2.219 0.365,0.229 10 false VC 2.073,0.656 2.188,0.833 0.115,0.177 10 false 6 4.365,0.656 4.719,0.823 0.354,0.167 10 false 122 4.708,0.656 5.125,0.833 0.417,0.177 10 false VTA1 1.688,0.76 2.094,0.969 0.406,0.208 10 false VTA 2.083,1.292 2.177,1.458 0.094,0.167 10 false 4 4.438,1.281 4.698,1.448 0.26,0.167 10 false 89 4.708,1.292 5.104,1.469 0.396,0.177 10 false VTA2 1.646,1.396 2.021,1.583 0.375,0.188 10 false VTA2 2.083,2.531 2.229,2.708 0.146,0.177 10 false 3 4.365,2.531 4.615,2.677 0.25,0.146 10 false 120 4.719,2.51 5.042,2.688 0.323,0.177 10 false ETA 1.802,2.615 2.052,2.802 0.25,0.188 10 false E2 0.052,3.156 0.615,3.427 0.563,0.271 10 false C41 0.063,3.333 3.917,3.583 3.854,0.25 10 false Throttle Position Sensor (Throttle Body with Motor Assembly) 5.292,3.208 5.906,3.49 0.615,0.281 10 false ECM 5,3.208 5.365,3.427 0.365,0.219 10 false C1 5.969,1.792 6.375,1.948 0.406,0.156 10 false 5 V

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (THROTTLE POSITION SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Throttle Position Sensor No.1 Voltage and Throttle Position Sensor No.2 Voltage.

Powertrain > Engine > Data List
Tester Display
Throttle Position Sensor No.1 Voltage
Throttle Position Sensor No.2 Voltage
50003 372 75,76

e.

Read the values displayed on the GTS.

Result:
When Accelerator Pedal Fully Released When Accelerator Pedal Fully Depressed (Engine Running) Trouble Area Proceed to
Throttle Position Sensor No.1 Voltage (VTA1) Throttle Position Sensor No.2 Voltage (VTA2) Throttle Position Sensor No.1 Voltage (VTA1) Throttle Position Sensor No.2 Voltage (VTA2)
0 to 0.2 V 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V VCTA circuit open A
4.5 to 4.98 V 4.5 to 4.98 V 4.5 to 4.98 V 4.5 to 4.98 V ETA circuit open
0 to 0.2 V, or 4.5 to 4.98 V 2.1 to 3.1 V
(Fail-safe)
0 to 0.2 V, or 4.5 to 4.98 V 2.1 to 3.1 V
(Fail-safe)
VTA1 circuit open or ground short
0.6 to 1.4 V
(Fail-safe)
0 to 0.2 V, or 4.5 to 4.98 V 0.6 to 1.4 V
(Fail-safe)
0 to 0.2 V, or 4.5 to 4.98 V VTA2 circuit open or ground short
0.6 to 1.1 V 2.1 to 3.1 V 3.2 to 4.8 V
(Not fail-safe)
4.6 to 4.98 V
(Not fail-safe)
Throttle position sensor circuit normal B



HINT:
·

DTC P01201C is stored when the VTA1 and VTA2 output voltages are not consistent with the sensor characteristics. Therefore, check the freeze frame data when this DTC is stored. Use the following formula to confirm the relative differences in voltage.

Characteristic Sensor Output:

VTA2 x 0.8 is approximately equal to VTA1 + 1.11 V

VTA1: Throttle Position Sensor No.1 Voltage

VTA2: Throttle Position Sensor No.2 Voltage


·

If DTC P01201C is output, proceed to "Check Harness And Connector (Throttle Position Sensor - ECM)".




A

2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)

B

5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM)
a.

Disconnect the throttle body with motor assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C41-5 (VC) - C1-121 (VCTA) Always Below 1 Ω
C41-6 (VTA) - C1-122 (VTA1) Always Below 1 Ω
C41-4 (VTA2) - C1-89 (VTA2) Always Below 1 Ω
C41-3 (E2) - C1-120 (ETA) Always Below 1 Ω
C41-5 (VC) or C1-121 (VCTA) - Body ground and other terminals Always 10 kΩ or higher
C41-6 (VTA) or C1-122 (VTA1) - Body ground and other terminals Always 10 kΩ or higher
C41-4 (VTA2) or C1-89 (VTA2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT ECM (VC VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT ECM (VC VOLTAGE)
A200902C70
0.563,0.948 0.906,1.198 0.344,0.25 1.302,1.646 1.646,1.135 true 2.26,1.698 1.938,1.125 true 0.604,0.99 0.917,1.177 0.313,0.188 10 false C41 0.146,0.083 0.458,0.281 0.313,0.198 10 false *a 1.198,1.656 1.51,1.854 0.313,0.198 10 false E2 2.198,1.74 2.51,1.938 0.313,0.198 10 false VC
*a Front view of wire harness connector
(to Throttle Body with Motor Assembly)


a.

Disconnect the throttle body with motor assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C41-5 (VC) - C41-3 (E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

4.REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

NG

4.REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY
a.

Replace the throttle body with motor assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>THROTTLE BODY>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Trouble Codes.


j.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
DTC P012011, P012015, P01201C, P022011, P022015 and/or P21352B are output A
DTCs are not output B




A

B

END