Home › Engine / Hybrid System › 2GR-FKS FUEL › FUEL PUMP › from 2016.11
RM3160E _51 Engine / Hybrid System _060158 2GR-FKS FUEL _0299120 FUEL PUMP A

2GR-FKS FUEL  FUEL PUMP  INSTALLATION  


PROCEDURE

Hide 77020A 1.INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

a.

Install a new fuel suction tube set gasket to the fuel tank assembly.


b.
A368920C01
0.24,0.26 0.344,0.26 0.344,0.26 0.458,0.656 false 1.354,2.458 1.771,2.458 true 0.094,0.167 0.406,0.323 0.313,0.156 10 false *a 1.167,2.375 1.344,2.542 0.177,0.167 10 true *b
*a Protrusion
*b Notch


Set the fuel suction tube with pump and gauge assembly to the fuel tank assembly.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.


HINT:

Align the protrusion of the fuel suction tube with pump and gauge assembly with the notch of the tank suction tube support.



Hide 77144 2.INSTALL FUEL PUMP GAUGE RETAINER

a.
A368922C01
0.906,0.208 1.208,0.208 true 1.021,0.667 1.458,0.667 true 0.708,0.125 0.917,0.292 0.208,0.167 10 true *a 0.823,0.583 1,0.771 0.177,0.188 10 true *b
*a "S" Mark
*b Triangle Mark


Align the triangle mark on a new fuel pump gauge retainer with the "S" mark on the fuel tank assembly and while pushing down the fuel suction tube with pump and gauge assembly, attach the fuel pump gauge retainer.


b.

Install SST (fuel pump retainer tool assy) to the fuel pump gauge retainer.

i.

Insert 2 SST (claw) between the service hole and fuel pump gauge retainer, and adjust the position so that the protrusions of the fuel pump gauge retainer are aligned with the grooves of SST (claw) as shown in the illustration.

A368923C01
2.76,0.76 3.125,0.76 true 3.854,1.542 4.219,1.542 true 1.115,3.135 1.042,2.417 1.042,2.417 1.833,2.781 true 2.083,2.979 2.458,2.385 2.458,2.385 2.604,2.385 true 1.146,3.198 1.667,3.458 1.667,3.458 1.865,2.865 true 4.521,2.792 5.542,2.302 5.542,2.302 5.375,2.896 true 4.531,2.854 4.844,3.438 4.844,3.438 5.344,2.958 true 2.542,0.667 2.74,0.844 0.198,0.177 10 true *a 2.656,2.302 2.833,2.458 0.177,0.156 10 true *b 1.635,3.479 1.813,3.646 0.177,0.167 10 true *c 0.844,2.281 1,2.458 0.156,0.177 10 true *d 0.583,2.042 0.771,2.219 0.188,0.177 10 true *e 3.865,2.063 4.01,2.24 0.146,0.177 10 true *f 4.26,1.448 4.458,1.625 0.198,0.177 10 true *a 4.74,3.469 4.917,3.635 0.177,0.167 10 true *c 5.594,2.188 5.75,2.365 0.156,0.177 10 true *d
*a SST (Claw) *b Triangle Mark
*c Protrusion of Fuel Pump Gauge Retainer *d Groove of SST (Claw)
*e Correct *f Incorrect


SST
09808-14040  (09882-14040)

NOTICE:

Ensure that SST (claw) does not cover the triangle mark of the fuel pump gauge retainer.



ii.
A368924C01
0.885,1.021 1.167,1.021 true 2.042,1.688 2.042,1.865 true 0.896,0.458 1.177,0.458 true 0.667,0.938 0.865,1.094 0.198,0.156 10 true *a 0.677,0.385 0.865,0.531 0.188,0.146 10 true *b 1.698,0.146 1.885,0.302 0.188,0.156 10 true *c 1.969,1.885 2.167,2.042 0.198,0.156 10 true *a 2.313,0.635 2.5,0.792 0.188,0.156 10 true *c
*a SST (Claw)
*b SST (Plate)
*c SST (Bolt and Washer Set)


While ensuring that SST (plate) is centered, install SST (plate) to 2 SST (claw) with 2 SST (bolt and washer set).

SST
09808-14040  (09881-14040, 09883-14040)



c.
A368926C01
1.042,0.917 1.354,0.917 true 2.01,3.719 2.323,3.719 true 0.823,0.813 1,0.969 0.177,0.156 10 true *a 1.823,3.625 2,3.792 0.177,0.167 10 true *b 2.531,4.031 2.719,4.219 0.188,0.188 10 true *c
*a SST (Fuel Pump Retainer Tool Assy)
*b Triangle Mark
*c "SERVICE" Range


While lightly pushing down on SST (fuel pump retainer tool assy), tighten the fuel pump gauge retainer by 1 and a half turns so that the triangle mark on the fuel pump gauge retainer is positioned between the "SERVICE" range on the fuel tank assembly.

NOTICE:
·

Do not use any tools other than specified as this may result in damage to the fuel pump gauge retainer or fuel tank assembly.

·

Do not push down on SST (fuel pump retainer tool assy) excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.

·

Make sure to turn the breaker bar horizontally. If it is turned at an angle, SST (fuel pump retainer tool assy) may come off.

·

Do not spin SST (fuel pump retainer tool assy) too fast or use an impact wrench as this may damage components.

·

If SST (fuel pump retainer tool assy) comes off of the fuel pump gauge retainer, loosen SST (bolt and washer set) and reinstall SST (fuel pump retainer tool assy).



HINT:

While pushing down on SST (fuel pump retainer tool assy), turn the fuel pump gauge retainer clockwise to tighten. Make sure that the detent of the tank suction tube support does not move out of the groove of the fuel tank assembly.



Hide 77209F 3.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A368927C01
2.052,1.552 2.469,1.552 true 2.427,2.344 2.844,2.344 false 2.188,2.052 2.385,2.052 false 2.177,2.5 2.74,2.5 false 2.167,2.625 2.542,2.625 2.542,2.625 2.542,2.5 false 2.594,3.969 2.802,3.969 false 1.208,3.875 1.448,3.875 false 1.302,4.396 1.198,4.396 1.198,4.396 0.969,4.01 true 2.375,3.917 2.542,3.531 2.542,3.531 2.677,3.531 true 2.896,2.26 3.208,2.417 0.313,0.156 10 false *1 2.448,1.969 2.76,2.125 0.313,0.156 10 false *a 2.802,2.427 3.115,2.583 0.313,0.156 10 false *b 0.292,3.302 0.604,3.458 0.313,0.156 10 false *d 1.823,3.354 2.135,3.51 0.313,0.156 10 false *e 2.531,1.469 2.708,1.635 0.177,0.167 10 true *1 1.49,3.792 1.802,3.948 0.313,0.156 10 false *1 2.854,3.896 3.167,4.052 0.313,0.156 10 false *1 1.354,4.323 1.667,4.479 0.313,0.156 10 false *c 2.74,3.448 3.052,3.604 0.313,0.156 10 false *c
*1 Tube Joint Clip
*a Fuel Tube Joint
*b O-ring
*c Collar
*d Correct
*e Incorrect


Push the fuel tube joint onto the plug of the fuel suction plate sub-assembly, then install the tube joint clip.

NOTICE:
·

Check that there are no scratches or foreign matter around the connecting parts of the fuel tube joint and plug before performing this work.

·

Check that the fuel tube joint is securely inserted to the end.

·

Check that the tube joint clip is on the collar of the fuel tube joint.

·

After installing the tube joint clip, check that the fuel tank main tube sub-assembly is securely connected by pulling on it.




Hide 4. CHECK AIRTIGHTNESS

a.
A393315

After installing the fuel suction tube with pump and gauge assembly, check for fuel leaks by first applying soapy water to the area where the fuel suction plate sub-assembly and fuel pump gauge retainer contact, and then blow forcefully into the fuel inlet area through a flexible pouring spout or similar tube.


b.

Blow forcefully until the reverse flow prevention valve inside the fuel inlet activates.

NOTICE:

Be careful not to inhale any fuel vapor.


HINT:

There should be a faintly audible sound when the reverse flow prevention valve operates.



c.
A368928C01
2.177,0.875 2.479,0.375 2.479,0.375 2.656,0.375 true 2.698,0.281 2.875,0.458 0.177,0.177 10 true *a
*a Air Bubbles


If improper installation of the fuel suction tube with pump and gauge assembly, etc. has resulted in a condition where fuel will leak, air will leak out as shown in the illustration.

NOTICE:

If air leaks out, recheck the installation condition, and replace the fuel pump gauge retainer and fuel suction tube set gasket with new ones. Also, make sure to fully wipe away the soapy water. (Any remaining soapy water can cause the fuel suction tube set gasket to slip and result in an improper seal.)



Hide 58325E 5.INSTALL REAR FLOOR SERVICE HOLE COVER

a.

Remove any remaining butyl tape from the rear floor service hole cover and vehicle body.


b.

Clean the installation surfaces of the rear floor service hole cover and vehicle body.


c.

Connect the 2 fuel pump connectors.


d.
A394251C01
0.708,1.552 1.115,1.552 true 0.51,1.469 0.708,1.625 0.198,0.156 10 true *a
*a Butyl Tape Adhesion Area


Install the rear floor service hole cover with new butyl tape.

NOTICE:

Securely install the rear floor service hole cover.



e.

Return the front floor carpet to its original position.


Hide 6.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 64740C 8.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH

Hide 66311 9.INSTALL ROPE HOOK (for LH Side)

Hide 64725F 10.INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for LH Side)

Hide 64974 11.INSTALL DECK TRIM POCKET COVER (for LH Side)

Hide 73570 12.CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY LH

Hide 64735 13.INSTALL DECK TRIM SIDE SERVICE HOLE COVER

Hide 64715E 14.INSTALL NO. 2 DECK SIDE TRIM COVER

Hide 73370C 15.CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY LH

Hide 64713F 16.INSTALL FRONT DECK SIDE TRIM COVER LH

Hide 64730B 17.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH

Hide 66311 18.INSTALL ROPE HOOK (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 64725F 19.INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 64974 20.INSTALL DECK TRIM POCKET COVER (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 81330 21.INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY

Hide 62627D 22.INSTALL SIDE TRIM COVER RH (w/o Rear Automatic Air Conditioning System)

Hide 88625T 23.INSTALL COOLER (NO. 2 ROOM TEMP. SENSOR) THERMISTOR (w/ Rear Automatic Air Conditioning System)

Hide 73560 24.CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 73297E 25.INSTALL DECK TRIM SIDE BELT HOLE COVER RH

Hide 64714H 26.INSTALL NO. 1 DECK SIDE TRIM COVER

Hide 73360C 27.CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 64712F 28.INSTALL FRONT DECK SIDE TRIM COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 29.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

Hide 67918A 30.INSTALL REAR DOOR SCUFF PLATE LH

Hide 72138M 31.INSTALL REAR OUTER SEAT TRACK BRACKET COVER LH

Hide 32.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

Hide 67917A 33.INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 72137S 34.INSTALL REAR OUTER SEAT TRACK BRACKET COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 35.INSTALL REAR NO. 2 SEAT ASSEMBLY

Hide 64910J 36.INSTALL TONNEAU COVER ASSEMBLY

Hide 58387B 37.INSTALL REAR FLOOR FINISH PLATE

Hide 64993 38.INSTALL REAR DECK FLOOR BOX

Hide 64742C 39.INSTALL DECK SIDE TRIM BOX LH

Hide 58409A 40.INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY

Hide 58410B 41.INSTALL DECK BOARD ASSEMBLY

Hide 42.INSTALL REAR NO. 1 SEAT ASSEMBLY

Hide 43.PERFORM INITIALIZATION

a.

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION