Home › Engine / Hybrid System › 2GR-FKS FUEL › FUEL SYSTEM › from 2016.11
RM3160E _51 Engine / Hybrid System _060158 2GR-FKS FUEL _0298776 FUEL SYSTEM G

2GR-FKS FUEL  FUEL SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.CHECK FUEL PUMP OPERATION AND INSPECT FOR FUEL LEAK

a.

Check fuel pump operation.

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine / Active Test / Activate the Circuit Relay.

Powertrain > Engine > Active Test
Tester Display
Activate the Circuit Relay
50004 372 40

v.

Check for pressure in the fuel tube sub-assembly from the fuel line. Check that sounds of fuel flowing from the fuel tank assembly can be heard. If no sounds can be heard, check the relay, fuel pump, ECM and wiring connectors.



b.

Inspect for fuel leaks.

i.

Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.



c.

Turn the ignition switch off.


d.

Disconnect the GTS from the DLC3.


Hide 2.CHECK FUEL PRESSURE

a.

Discharge fuel system pressure.

Click hereEngine / Hybrid System>2GR-FKS FUEL>FUEL SYSTEM>PRECAUTION


b.

Measure the battery voltage.

Standard Voltage:

11 to 14 V



c.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



d.
A412601C01
0.135,0.063 0.479,0.26 0.344,0.198 12 false *A 0.198,2.458 0.521,2.708 0.323,0.25 12 false *B
*A Fuel Pipe Camp Type A
*B Fuel Pipe Camp Type B


Disengage the 2 claws to remove the No. 2 fuel pipe clamp.


e.
A412602C01
0.177,0.073 0.49,0.271 0.313,0.198 12 false *A 0.188,2.406 0.469,2.635 0.281,0.229 12 false *B
*A Fuel Pipe Camp Type A
*B Fuel Pipe Camp Type B


Remove the No. 1 fuel pipe clamp from the fuel tube connector.


f.

Disconnect the No. 2 fuel tube sub-assembly (for Direct Injection).

i.
A393288

Disconnect the No. 2 fuel tube sub-assembly from the fuel pipe.

Click hereEngine / Hybrid System>2GR-FKS FUEL>FUEL SYSTEM>PRECAUTION



g.

Disconnect the fuel tube sub-assembly (for Port Injection).

i.
A393287

Disconnect the fuel tube sub-assembly from the fuel pipe.

Click hereEngine / Hybrid System>2GR-FKS FUEL>FUEL SYSTEM>PRECAUTION



h.
A393289C01
0.219,1.031 0.333,1.031 0.333,1.031 0.427,1.292 false 1.594,0.354 1.708,0.354 1.708,0.354 1.833,0.438 false 2.594,1.104 2.792,0.719 2.792,0.719 2.896,0.719 false 0.938,3.083 1.146,3.083 false 1.083,3.75 1.292,3.75 false 1.167,4.083 1.375,4.083 false 2.719,2.563 2.865,2.25 2.865,2.25 2.948,2.25 false 1.365,1.917 1.438,1.635 1.438,1.635 1.531,1.635 false 1.385,1.094 1.385,0.906 false 1.76,1.26 1.875,1.26 1.875,1.26 1.99,1.021 false 1.302,1.115 1.615,1.271 0.313,0.156 10 false *1 1.427,0.26 1.74,0.417 0.313,0.156 10 false *a 1.604,1.177 1.917,1.333 0.313,0.156 10 false *b 0.063,0.938 0.375,1.094 0.313,0.156 10 false *c 1.573,1.552 1.885,1.708 0.313,0.156 10 false *d 3,2.167 3.313,2.323 0.313,0.156 10 false *e 0.927,3.667 1.24,3.823 0.313,0.156 10 false *f 1.01,3.979 1.25,4.208 0.24,0.229 10 false *g 2.938,0.635 3.25,0.792 0.313,0.156 10 false *a 0.781,2.979 1.094,3.135 0.313,0.156 10 false *a
*1 Fuel Tube Sub-assembly (Vehicle Side)
*a SST (Hose Band)
*b SST (T-joint)
*c SST (Gauge)
*d SST (Hose Joint)
*e SST (Hose)
*f SST (Fuel Tube Connector)
*g Fuel Pipe (Vehicle Side)


Install SST (EFI fuel pressure gauge) as shown in the illustration.

SST
09268-45101  (09268-41250, 09268-41260, 09268-41280, 09268-41500, 09268-41700, 95336-08070)


i.

Wipe up any spilled fuel.


j.

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



k.

Connect the GTS to the DLC3.


l.

Turn the engine switch on (IG).

NOTICE:

Do not start the engine.



m.

Turn the GTS on.


n.

Enter the following menus: Powertrain / Engine / Active Test / Activate the Circuit Relay.

Powertrain > Engine > Active Test
Tester Display
Activate the Circuit Relay
50004 372 40

o.

Measure the fuel pressure.

Standard Fuel Pressure:

196 to 833 kPa (2.0 to 8.5 kgf/cm2, 28 to 121 psi)


·

If the fuel pressure is less than the standard, check the fuel hoses and their connections, fuel pump, fuel filter and fuel main valve assembly.

·

If the result is not as specified, replace the fuel main valve assembly.



p.

Disconnect the GTS from the DLC3.


q.

Start the engine.


r.

Measure the fuel pressure at idle.

Standard Fuel Pressure:

196 to 833 kPa (2.0 to 8.5 kgf/cm2, 28 to 121 psi)


HINT:

Refer to Standard Idle Speed.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION



s.

Stop the engine.


t.

Check that the fuel pressure remains as specified for 5 minutes.

Standard Fuel Pressure:

98 kPa (1.0 kgf/cm2, 14.2 psi) or more


If the result is not as specified, check the fuel pump, fuel main valve assembly and/or fuel injector assemblies.


u.

After checking the fuel pressure, disconnect the cable from the negative (-) battery terminal and carefully remove SST to prevent fuel from spraying.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



v.

Connect the fuel tube sub-assembly (for Port Injection).

i.

Connect the fuel tube sub-assembly to the fuel pipe.

Click hereEngine / Hybrid System>2GR-FKS FUEL>FUEL SYSTEM>PRECAUTION



w.

Connect the No. 2 fuel tube sub-assembly (for Direct Injection).

i.

Connect the No. 2 fuel tube sub-assembly to the fuel pipe.

Click hereEngine / Hybrid System>2GR-FKS FUEL>FUEL SYSTEM>PRECAUTION



x.

Install the No. 1 fuel pipe clamp to the fuel tube connector.


y.

Fuel Pipe Clamp Type A:

i.

Engage the 2 claws to install the No. 2 fuel pipe clamp.



z.
A412603C01
0.833,2.042 1.354,2.042 1.354,2.042 1.354,1.854 false 1.125,2.042 1.125,1.771 false 2.646,1.792 2.052,1.792 2.052,1.792 2.052,1.438 true 2.26,1.792 2.26,1.583 true 0.667,1.948 0.979,2.104 0.313,0.156 10 false *a 2.677,1.708 2.99,1.865 0.313,0.156 10 false *b
*a Protrusion
*b Notch


Fuel Pipe Clamp Type B:

i.

Align the protrusions of the No. 2 fuel pipe clamp with the notches of the No. 1 fuel pipe clamp, and engage the 2 claws to install the No. 2 fuel pipe clamp.




Hide 3.CHECK FUEL PRESSURE (for High Pressure)

a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Start and warm up the engine.


e.

Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (High).

Powertrain > Engine > Data List
Tester Display
Fuel Pressure (High)
50003 372 265

f.

Check the high pressure side fuel pressure at 3000 rpm (shift lever in N, engine warmed up and A/C off).

Standard Fuel Pressure:

2400 to 19500 kPa (24.5 to 198.8 kgf/cm2, 348 to 2828 psi)


If the result is not as specified, check the fuel pump, fuel pump assembly, fuel pressure sensor and wire harnesses.


g.

Stop the engine.