Home › Drivetrain › MF1A (TRANSFER / 4WD / AWD) › DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM › from 2016.11
RM3160E _52 Drivetrain _019685 MF1A TRANSFER / 4WD / AWD _0109466 DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM J

MF1A TRANSFER / 4WD / AWD  DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM  AWD Warning Remains ON  


DESCRIPTION

The 4WD ECU assembly is connected to the combination meter assembly via the CAN communication system. If any of the following conditions are detected, the multi-information display indicates a malfunction in the dynamic torque control 4WD/AWD system.

·

There is a malfunction in the 4WD ECU assembly internal circuit.

·

A low voltage is applied to the power source for the 4WD ECU assembly.

·

There is a malfunction in the CAN communication system.

·

There is a malfunction in the brake control system.

·

During fail-safe function.


WIRING DIAGRAM

C284983E13
5.698,5.094 7.083,5.365 1.385,0.271 10 false 4WD ECU Assembly 0.313,3.125 2.177,3.313 1.865,0.188 10 false Combination Meter Assembly 4.49,2.99 5.167,3.198 0.677,0.208 10 false IG1 NO. 2 1.073,5.125 2.906,5.271 1.833,0.146 10 false : CAN Communication Line 0.677,1.083 1.708,1.469 1.031,0.385 10 false Multi-information Display 6.135,2.823 6.594,3.021 0.458,0.198 10 false IG1 6.125,3.75 6.583,3.948 0.458,0.198 10 false GND 2.313,2.813 3.531,3.063 1.219,0.25 10 false from IG1 Circuit 5.708,4.917 6.167,5.115 0.458,0.198 10 false F14 5.917,2.688 6.073,2.885 0.156,0.198 10 false 3 5.917,3.594 6.073,3.792 0.156,0.198 10 false 4 0.302,2.958 0.76,3.156 0.458,0.198 10 false F126

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Check the condition of each related circuit connector before troubleshooting.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


PROCEDURE

1.CHECK FOR DTC (CAN COMMUNICATION SYSTEM AND DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM)
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


b.

Check if the dynamic torque control 4WD/AWD system DTC is output.

Click hereDrivetrain>MF1A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM>DTC CHECK / CLEAR

Chassis > Four Wheel Drive > Trouble Codes
50001 118

HINT:

When DTCs indicating a CAN communication system malfunction are output, repair the CAN communication system before repairing each corresponding sensor.


Result:
Result Proceed to
Neither CAN communication system DTCs nor dynamic control 4WD/AWD system DTCs are output A
CAN communication DTCs are output B
Dynamic torque control 4WD/AWD system DTCs are output C



A

2.CHECK 4WD ECU ASSEMBLY

B

GO TO CAN COMMUNICATION (HOW TO PROCEED WITH TROUBLESHOOTING)

C

REPAIR CIRCUIT INDICATED BY OUTPUT CODE (DYNAMIC TORQUE CONTROL 4WD/AWD SYSTEM)

2.CHECK 4WD ECU ASSEMBLY
a.

Check if the 4WD ECU assembly connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.INSPECT BATTERY

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.INSPECT BATTERY
a.

Check the battery voltage.

Standard Voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

NG

4.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.
C270074C28
2.406,0.094 2.813,0.354 0.406,0.26 1.938,1.927 2.24,1.927 2.24,1.927 2.333,1.177 true 1.677,1.854 2.021,2.052 0.344,0.198 10 false IG1 2.49,0.146 2.802,0.344 0.313,0.198 10 false F14 0,0 0.313,0.156 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to 4WD ECU Assembly)


Disconnect the F14 4WD ECU assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F14-3 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.

Turn the ignition switch off.


b.
C270074C29
2.396,0.104 2.802,0.365 0.406,0.26 2.167,1.917 2.417,1.917 2.417,1.917 2.583,1.167 true 1.833,1.833 2.177,2.031 0.344,0.198 10 false GND 2.49,0.146 2.802,0.344 0.313,0.198 10 false F14 0,0 0.313,0.156 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to 4WD ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F14-4 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (4WD WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.READ VALUE USING GTS (4WD WARNING LIGHT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / Four Wheel Drive / Data List.


e.

According to the display on the GTS, read the Data List.

Chassis > Four Wheel Drive > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
4WD Warning Light AWD warning (multi-information display) OFF or ON OFF: Warning off
ON: Warning on
-
Chassis > Four Wheel Drive > Data List
Tester Display
4WD Warning Light
50003 118 7

f.

Check the GTS display condition of the 4WD warning light.


Result:
Result Proceed to
Display of the Data List remains OFF A
Display of the Data List remains ON B



A

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

B