Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.11
RM3160E _54 Brake _019692 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0106374 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C142B  Motor Power Supply Voltage Circuit  C146C  Open in ABS Motor Relay Circuit  C146D  Short in ABS Motor Relay Circuit  


DESCRIPTION

These DTCs are stored when a problem is identified in the skid control ECU (brake actuator assembly).

The ABS motor relay supplies power to the pump motor. While the ABS is activated, the ECU turns the ABS motor relay on and operates the pump motor.

If the voltage supplied to the ABS motor relay (BM) is below the DTC detection threshold due to low voltage from the battery or alternator, these DTCs may be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C142B Motor Power Supply Voltage Circuit When voltage at +BS terminal is 9.5 V or higher, open in BM terminal continues for 1 second or more.
·

Wire harness or connector

·

Skid control ECU (brake actuator assembly)


C146C Open in ABS Motor Relay Circuit When voltage at +BS terminal is 9.5 V or higher and motor relay ON while control operates, relay contact OFF condition continues for 0.12 seconds or more.
·

Wire harness or connector

·

Skid control ECU (brake actuator assembly)


C146D Short in ABS Motor Relay Circuit Either of the following is detected:
1.

Overcurrent in motor relay and motor fail-safe relay continues for 0.05 seconds or more.

2.

Motor relay gate voltage malfunction continues for 0.12 seconds or more.


·

Wire harness or connector

·

Skid control ECU (brake actuator assembly)



HINT:

for C146C: Even after the trouble areas are repaired, the ABS warning light will not go off unless the following operations are performed.

1.

Drive the vehicle at 30 km/h (19 mph) for 30 seconds or more and check that the ABS warning light goes off.

2.

Clear the DTCs.



WIRING DIAGRAM

C285309E10
1.927,1.302 2.083,1.5 0.156,0.198 10 false 1 2.396,1.302 2.552,1.5 0.156,0.198 10 false 2 1.844,1.583 2.938,1.844 1.094,0.26 10 false ABS NO. 1 3.521,1.271 3.75,1.583 0.229,0.313 10 false 13 3.594,3.229 3.813,3.417 0.219,0.188 10 false 1 3.823,1.563 4.219,1.844 0.396,0.281 10 false BM 3.813,3.51 4.229,3.698 0.417,0.188 10 false GND2 4.354,4.094 4.969,4.375 0.615,0.281 10 false GNDM 6.448,4.083 6.76,4.281 0.313,0.198 10 false BM 4.906,1.427 6.333,1.771 1.427,0.344 10 false ABS Motor Relay 4.917,2.25 6.24,2.667 1.323,0.417 10 false Skid Control ECU 4.823,3.271 6.115,3.656 1.292,0.385 10 false ABS Motor Fail-safe Relay 4.406,5.156 5.042,5.583 0.635,0.427 10 false A86 4.75,5.156 6.688,5.396 1.938,0.24 10 false Brake Actuator Assembly 0.885,4.094 1.552,4.333 0.667,0.24 10 false Battery 5.271,4.771 6.802,4.969 1.531,0.198 10 false Pump Motor

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:

When C1241 and/or C1417 is output together with C142B, C146C and/or C146D, inspect and repair the trouble areas indicated by C1241 and/or C1417 first.

for C1241: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1241

for C1417: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1417


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BM TERMINAL)
a.
C364228C17
1.479,0.104 1.906,0.375 0.427,0.271 2.958,1.833 2.708,0.948 true 1.573,0.156 2.031,0.354 0.458,0.198 10 false A86 2.875,1.865 3.333,2.063 0.458,0.198 10 false BM 0.24,0.208 0.698,0.406 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A86 skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A86-13 (BM) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (+BM CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)
a.
C364228C18
1.479,0.104 1.906,0.375 0.427,0.271 0.479,1.792 0.688,0.938 true 1.573,0.156 2.031,0.354 0.458,0.198 10 false A86 0.344,1.844 0.802,2.042 0.458,0.198 10 false GND2 0.24,0.208 0.698,0.406 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A86-1 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND2 CIRCUIT)

3.RECONFIRM DTC
HINT:

This DTC is stored when a problem is identified in the skid control ECU (brake actuator assembly).

The ABS motor relay is in the skid control ECU (brake actuator assembly).

Therefore, ABS motor relay inspection and ABS motor relay unit inspection cannot be performed. Be sure to check if the DTC is output again before replacing the skid control ECU (brake actuator assembly).


a.

Reconnect the A86 skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch off.


c.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

d.

Turn the ignition switch off.


e.

Start the engine.


f.

Perform a road test.


g.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTCs C142B, C146C and C146D are not output. A
DTCs C142B, C146C and/or C146D are output. B


HINT:
·

If a speed signal of 6 km/h (4 mph) or more is sent to the skid control ECU (brake actuator assembly) with the ignition switch ON and the stop light switch assembly off, the ECU performs self diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (no DTCs are output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU (brake actuator assembly).

·

If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

If no DTCs were output when reconfirming DTCs, checking for intermittent problems is necessary because it is suspected that the original DTCs were stored due to the poor connection of a connector terminal.





A

B