Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.11
RM3160E _54 Brake _019692 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0106374 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1381  Acceleration Sensor Power Supply Voltage Malfunction  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the yaw rate and acceleration sensor (airbag ECU assembly) via the CAN communication system.

The airbag ECU assembly has a built-in yaw rate and acceleration sensor and detects the vehicle's condition using 2 circuits (GL1, GL2).

If there is trouble in the bus lines between the acceleration sensor (airbag ECU assembly) and the CAN communication system, the DTC U0124 (Lost Communication with Lateral Acceleration Sensor Module) is output.

These DTCs are also output when calibration has not been completed.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1381 Acceleration Sensor Power Supply Voltage Malfunction At a vehicle speed of more than 3 km/h (2 mph), an acceleration sensor power source malfunction signal is received for 10 seconds or more.
·

Acceleration sensor (airbag ECU assembly)

·

Wire harness or connector



WIRING DIAGRAM

C270520E80
0.813,0.719 1.427,0.917 0.615,0.198 10 false CANL 6.052,0.708 6.667,0.906 0.615,0.198 10 false CANL 0.802,1.333 1.417,1.531 0.615,0.198 10 false CANH 6.052,1.333 6.667,1.531 0.615,0.198 10 false CANH 0.958,1.938 1.417,2.135 0.458,0.198 10 false IG2 2.167,2.094 2.938,2.333 0.771,0.24 10 false A/BAG-IG 3.927,1.927 4.917,2.135 0.99,0.208 10 false from IG2 Relay 1,2.552 1.313,2.75 0.313,0.198 10 false E1 1,3.167 1.313,3.365 0.313,0.198 10 false E2 0.083,4.073 2.229,4.479 2.146,0.406 10 false Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly) 0.094,3.927 0.552,4.125 0.458,0.198 10 false F38 3.49,3.125 5.49,3.375 2,0.25 10 false : CAN Communication Line 5.531,4.073 7.073,4.458 1.542,0.385 10 false Skid Control ECU (Brake Actuator Assembly) 5.542,3.896 6,4.094 0.458,0.198 10 false A86 5.781,0.531 6.094,0.729 0.313,0.198 10 false 10 5.792,1.167 6.104,1.365 0.313,0.198 10 false 22 1.281,0.542 1.594,0.74 0.313,0.198 10 false 22 1.271,1.167 1.583,1.365 0.313,0.198 10 false 13 1.281,1.833 1.594,2.031 0.313,0.198 10 false 21 1.281,2.448 1.594,2.646 0.313,0.198 10 false 25 1.281,3.063 1.594,3.26 0.313,0.198 10 false 26 2.188,1.844 2.344,2.042 0.156,0.198 10 false 2 2.667,1.844 2.823,2.042 0.156,0.198 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the yaw rate and acceleration sensor (airbag sensor assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IG2 TERMINAL)
a.
C239271C33
0.25,0.708 0.729,1 0.479,0.292 1.031,2.188 0.573,2.792 false 0.385,0.771 0.729,1.188 0.344,0.417 10 false F38 0.24,0.219 0.573,0.615 0.333,0.396 10 false *a 0.385,2.823 0.677,3 0.292,0.177 10 false IG2
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the F38 yaw rate and acceleration sensor (airbag sensor assembly) connector.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F38-21 (IG2) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.
C239271C34
0.25,0.708 0.729,1 0.479,0.292 1.635,2.188 1.198,2.813 false 1.802,2.188 2.271,2.813 false 0.385,0.771 0.844,1.031 0.458,0.26 10 false F38 0.24,0.219 0.458,0.396 0.219,0.177 10 false *a 1.052,2.844 1.281,3.021 0.229,0.177 10 false E1 2.208,2.844 2.438,3.021 0.229,0.177 10 false E2
*a Front view of wire harness connector
(to Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly))


Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F38-25 (E1) - Body ground Always Below 1 Ω
F38-26 (E2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)

3.RECONFIRM DTC
a.

Reconnect the F38 yaw rate and acceleration sensor (airbag sensor assembly) connector.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Perform a road test.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTC C1381 is not output. A
DTC C1381 is output B


NOTICE:

Check the yaw rate and acceleration sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

B