Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.11
RM3160E _54 Brake _019692 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0106374 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C146E  Open in ABS Solenoid Relay Circuit  C146F  Short in ABS Solenoid Relay Circuit  


DESCRIPTION

The ABS solenoid relay supplies power to the ABS solenoid and TRC solenoid.

The solenoid relay is turned on 1.5 seconds after the ignition switch is turned to ON, and is turned off if an open or short in the solenoid is detected by self diagnosis performed when the vehicle starts running.

The ABS solenoid relay is housed in the skid control ECU in the brake actuator assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
C146E Open in ABS Solenoid Relay Circuit Either of the following is detected:
1.

When voltage at terminal +BS is 9.5 V or higher and solenoid relay is ON, relay contact is OFF continuously for 0.22 seconds or more.

2.

When solenoid relay is turned on and voltage at +BS terminal is below 9.5 V, relay contact does not turn on after 0.22 seconds or more.


·

Wire harness or connector

·

Skid control ECU (brake actuator assembly)


C146F Short in ABS Solenoid Relay Circuit Immediately after the ignition switch is turned to ON, the ABS solenoid relay contact is closed for 4.5 seconds when the relay is turned off.
·

Wire harness or connector

·

Skid control ECU (brake actuator assembly)



WIRING DIAGRAM

C285311E08
1.677,1.083 1.865,1.281 0.188,0.198 10 false 1 2.219,1.073 2.417,1.271 0.198,0.198 10 false 2 1.667,1.375 2.458,1.594 0.792,0.219 10 false ABS NO. 2 0.635,3.969 1.427,4.188 0.792,0.219 10 false FL MAIN 3.26,1.073 3.51,1.26 0.25,0.188 10 false 38 3.531,1.323 3.865,1.542 0.333,0.219 10 false +BS 3.24,4.948 3.49,5.135 0.25,0.188 10 false 25 3.531,5.115 4.073,5.323 0.542,0.208 10 false GND1 4.281,8.302 4.823,8.51 0.542,0.208 10 false A86 6.031,7.552 6.427,7.74 0.396,0.188 10 false SM2 6.031,6.563 6.427,6.75 0.396,0.188 10 false SM1 5.99,5.594 6.469,5.781 0.479,0.188 10 false SRLR 5.99,5.104 6.469,5.292 0.479,0.188 10 false SRRR 5.99,4.615 6.469,4.802 0.479,0.188 10 false SFLR 5.99,4.094 6.469,4.281 0.479,0.188 10 false SFRR 5.99,3.604 6.469,3.792 0.479,0.188 10 false SRLH 5.99,3.115 6.469,3.302 0.479,0.188 10 false SRRH 5.99,2.615 6.469,2.802 0.479,0.188 10 false SFLH 5.99,2.104 6.469,2.292 0.479,0.188 10 false SFRH 4.625,8.302 6.708,8.552 2.083,0.25 10 false Brake Actuator Assembly 4.458,4.313 5.615,4.646 1.156,0.333 10 false Skid Control ECU 4.583,1.125 5.469,1.49 0.885,0.365 10 false ABS Solenoid Relay 0.729,6.854 1.521,7.073 0.792,0.219 10 false Battery

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:

When C1241 and/or C1417 is output together with C146E and/or C146F, inspect and repair the trouble areas indicated by C1241 and/or C1417 first.

for C1241: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1241

for C1417: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1417


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (+BS TERMINAL)
a.
C364228C21
1.479,0.104 1.906,0.375 0.427,0.271 2.708,1.823 2.646,1.24 true 1.573,0.156 2.031,0.354 0.458,0.198 10 false A86 2.635,1.854 3.094,2.052 0.458,0.198 10 false +BS 0.177,0.177 0.635,0.375 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A86 skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A86-38 (+BS) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (+BS CIRCUIT)

2.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
C364228C15
1.479,0.104 1.906,0.375 0.427,0.271 0.542,1.833 0.656,1.229 true 1.583,0.156 2.042,0.354 0.458,0.198 10 false A86 0.385,1.875 0.844,2.073 0.458,0.198 10 false GND1 0.219,0.167 0.677,0.365 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A86-25 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

3.RECONFIRM DTC
HINT:
·

This DTC is stored when a problem is identified in the skid control ECU (brake actuator assembly).

·

The solenoid circuits are located in the skid control ECU (brake actuator assembly). Therefore, solenoid circuit inspection and solenoid unit inspection cannot be performed. Be sure to check if the DTC is output again before replacing the skid control ECU (brake actuator assembly).



a.

Reconnect the A86 skid control ECU (brake actuator assembly) connector.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the ignition switch off.


d.

Start the engine.


e.

Perform a road test.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTCs C146E and C146F are not output. A
DTCs C146E and/or C146F are output. B


HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly) with the ignition switch ON and the stop light switch assembly off, the ECU performs self diagnosis of the solenoid circuit.

·

If the normal system DTC is output (no DTCs are output), slightly jiggle the connectors, wire harnesses, and fuses of the skid control ECU (brake actuator assembly).

·

If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

If no DTCs were output when reconfirming DTCs, checking for intermittent problems is necessary because it is suspected that the original DTCs were stored due to the poor connection of a connector terminal.





A

B