Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.11
RM3160E _54 Brake _019692 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0106374 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TS and CG Terminal Circuit  


DESCRIPTION

In Test Mode (signal check), a malfunction in a speed sensor that cannot be detected when the vehicle is stopped can be detected while driving.

Sensor check mode can be entered by connecting terminals TS and CG of the DLC3 and turning the ignition switch from off to ON

WIRING DIAGRAM

C369736E02
5.969,0.698 6.583,0.896 0.615,0.198 10 false CANL 5.698,0.51 6.313,0.708 0.615,0.198 10 false 10 5.979,1.385 6.594,1.583 0.615,0.198 10 false CANH 5.708,1.208 6.323,1.406 0.615,0.198 10 false 22 5.458,1.927 7.042,2.406 1.583,0.479 10 false Skid Control ECU (Brake Actuator Assembly) 5.469,1.74 6.083,1.938 0.615,0.198 10 false A86 0.927,0.708 1.542,0.906 0.615,0.198 10 false CANL 0.906,1.396 1.521,1.594 0.615,0.198 10 false CANH 6.125,4.313 6.74,4.51 0.615,0.198 10 false DLC3 5.979,2.958 6.594,3.156 0.615,0.198 10 false TS 6.135,4.146 6.75,4.344 0.615,0.198 10 false F25 5.708,2.854 6.323,3.052 0.615,0.198 10 false 12 5.781,3.458 6.396,3.656 0.615,0.198 10 false 4 5.979,3.583 6.594,3.781 0.615,0.198 10 false CG 2.792,3.719 4.5,4.031 1.708,0.313 10 false : CAN Communication Line 0.24,4.323 2.177,4.646 1.938,0.323 10 false Power Steering ECU Assembly 0.24,4.115 0.854,4.313 0.615,0.198 10 false p1 1.104,2.979 1.719,3.177 0.615,0.198 10 false TS 1.417,2.823 2.031,3.021 0.615,0.198 10 false 5 1.396,0.51 2.01,0.708 0.615,0.198 10 false 8 1.396,1.198 2.01,1.396 0.615,0.198 10 false 4

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

2.INSPECT DLC3

B

2.INSPECT DLC3
a.
C207407C88
0.25,0.979 0.698,1.271 0.448,0.292 1.625,2.375 1.917,1 true 1.594,1.885 1.135,1.01 true 0.333,0.302 0.521,0.469 0.188,0.167 10 false *a 1.865,0.813 2.104,0.979 0.24,0.167 10 false TS 0.375,1.042 0.792,1.333 0.417,0.292 10 false F25 1.021,0.813 1.26,0.979 0.24,0.167 10 false CG
*a Front view of DLC3


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F25-12 (TS) - F25-4 (CG) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK POWER STEERING ECU ASSEMBLY (TS of DLC3 INPUT)

NG

4.CHECK HARNESS AND CONNECTOR (TS of DLC3 - POWER STEERING ECU ASSEMBLY)
3.CHECK POWER STEERING ECU ASSEMBLY (TS of DLC3 INPUT)
a.
C207407C88
0.25,0.979 0.698,1.271 0.448,0.292 1.625,2.375 1.917,1 true 1.594,1.885 1.135,1.01 true 0.333,0.302 0.521,0.469 0.188,0.167 10 false *a 1.865,0.813 2.104,0.979 0.24,0.167 10 false TS 0.375,1.042 0.792,1.333 0.417,0.292 10 false F25 1.021,0.813 1.26,0.979 0.24,0.167 10 false CG
*a Front view of DLC3


Turn the ignition switch off.


b.

Using SST, connect terminals TS and CG of the DLC3.


SST
09843-18040  

c.

Check that the EPS warning light is blinking.

OK:

The EPS warning light is blinking.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

REPLACE POWER STEERING ECU ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (TS of DLC3 - POWER STEERING ECU ASSEMBLY)
a.

Turn the ignition switch off.


b.

Disconnect the p1 power steering ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F25-12 (TS) - p1-5 (TS) Always Below 1 Ω
F25-12 (TS) or p1-5 (TS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.
C207407C87
0.25,0.979 0.698,1.271 0.448,0.292 1.594,1.885 2.438,0.958 true 0.333,0.302 0.521,0.469 0.188,0.167 10 false *a 0.375,1.042 0.708,1.302 0.333,0.26 10 false F25 2.438,0.76 2.677,0.927 0.24,0.167 10 false CG
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F25-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK POWER STEERING ECU ASSEMBLY (TS of DLC3 INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK POWER STEERING ECU ASSEMBLY (TS of DLC3 INPUT)
a.
C207407C88
0.25,0.979 0.698,1.271 0.448,0.292 1.625,2.375 1.917,1 true 1.594,1.885 1.135,1.01 true 0.333,0.302 0.521,0.469 0.188,0.167 10 false *a 1.865,0.813 2.104,0.979 0.24,0.167 10 false TS 0.375,1.042 0.792,1.333 0.417,0.292 10 false F25 1.021,0.813 1.26,0.979 0.24,0.167 10 false CG
*a Front view of DLC3


Reconnect the p1 power steering ECU assembly connector.


b.

Using SST, connect terminals TS and CG of the DLC3.


SST
09843-18040  

c.

Check that the EPS warning light is blinking.

OK:

The EPS warning light is blinking.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

NG

REPLACE POWER STEERING ECU ASSEMBLY