Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) › from 2016.11
RM3160E _58 Vehicle Interior _019714 HEATING / AIR CONDITIONING _0109951 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1451/51  Compressor Solenoid Circuit  


DESCRIPTION

for 2GR-FKS

In this circuit, the cooler compressor assembly (compressor solenoid) receives a refrigerant compression demand signal from the air conditioning amplifier assembly.

Based on this signal, the cooler compressor assembly (compressor solenoid) changes the amount of compressor output.


for 1AR-FE

In this circuit, the compressor assembly with pulley (compressor solenoid) receives a refrigerant compression demand signal from the air conditioning amplifier assembly.

Based on this signal, the compressor assembly with pulley (compressor solenoid) changes the amount of compressor output.


DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1451/51 Compressor Solenoid Circuit Open or short in compressor solenoid circuit
·

Cooler compressor assembly (compressor solenoid)*1

·

Compressor assembly with pulley (compressor solenoid)*2

·

Harness or connector between air conditioning amplifier assembly and cooler compressor assembly (compressor solenoid)*1

·

Harness or connector between air conditioning amplifier assembly and compressor assembly with pulley (compressor solenoid)*2

·

Air conditioning amplifier assembly


-

*1: for 2GR-FKS

*2: for 1AR-FE


WIRING DIAGRAM

E229254E75
5.01,0.792 5.104,0.969 0.094,0.177 10 false 2 3.833,0.792 4.688,1.021 0.854,0.229 10 false 2 2.448,0.802 3.354,1.052 0.906,0.25 10 false 1 5.229,0.885 5.688,1.063 0.458,0.177 10 false SOL+ 3.385,0.792 3.76,0.969 0.375,0.177 10 false SOL+ 2.625,0.792 2.969,0.969 0.344,0.177 10 false SOL- 4.823,3.5 5.167,3.677 0.344,0.177 10 false F80 4.823,3.667 6.469,4 1.646,0.333 10 false Air Conditioning Amplifier Assembly 2.323,1.51 4.177,1.875 1.854,0.365 10 false Cooler Compressor Assembly (Compressor Solenoid)*1 2.323,1.354 3.229,1.677 0.906,0.323 10 false C16 2.208,3.698 3.854,4.031 1.646,0.333 10 false *1: for 2GR-FKS 2.219,4.021 3.865,4.354 1.646,0.333 10 false *2: for 1AR-FE 2.323,2.271 4.438,2.646 2.115,0.375 10 false Compressor Assembly with Pulley (Compressor Solenoid)*2

PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for 2GR-FKS A
for 1AR-FE B



A

2.INSPECT COOLER COMPRESSOR ASSEMBLY (COMPRESSOR SOLENOID)

B

5.INSPECT COMPRESSOR ASSEMBLY WITH PULLEY (COMPRESSOR SOLENOID)
2.INSPECT COOLER COMPRESSOR ASSEMBLY (COMPRESSOR SOLENOID)
E116970C07
1.51,0.729 1.885,0.969 0.375,0.24 1.115,2.427 1.531,2.01 false 2.344,2.448 1.99,2.01 false 0.24,0.219 0.552,0.375 0.313,0.156 10 false *a 0.875,2.458 1.396,2.656 0.521,0.198 10 false SOL+ 2.24,2.479 2.583,2.646 0.344,0.167 10 false SOL- 1.583,0.771 2.042,0.969 0.458,0.198 10 false C16
*a Component without harness connected
(Cooler Compressor Assembly (Compressor Solenoid))


a.

Disconnect the C16 cooler compressor assembly (compressor solenoid) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C16-1 (SOL-) - C16-2 (SOL+) 25°C (77°F) 10.1 to 11.1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (COOLER COMPRESSOR ASSEMBLY (COMPRESSOR SOLENOID) - BODY GROUND)

NG

REPLACE COOLER COMPRESSOR ASSEMBLY (COMPRESSOR SOLENOID)

3.CHECK HARNESS AND CONNECTOR (COOLER COMPRESSOR ASSEMBLY (COMPRESSOR SOLENOID) - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C16-1 (SOL-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (COOLER COMPRESSOR ASSEMBLY (COMPRESSOR SOLENOID) - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (COOLER COMPRESSOR ASSEMBLY (COMPRESSOR SOLENOID) - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the F80 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C16-2 (SOL+) - F80-2 (SOL+) Always Below 1 Ω
C16-2 (SOL+) or F80-2 (SOL+) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (When troubleshooting according to Problem Symptoms Table) A
OK (When troubleshooting according to the DTC) B
NG C



A

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT COMPRESSOR ASSEMBLY WITH PULLEY (COMPRESSOR SOLENOID)
E116970C07
1.51,0.729 1.885,0.969 0.375,0.24 1.115,2.427 1.531,2.01 false 2.344,2.448 1.99,2.01 false 0.24,0.219 0.552,0.375 0.313,0.156 10 false *a 0.875,2.458 1.396,2.656 0.521,0.198 10 false SOL+ 2.24,2.479 2.583,2.646 0.344,0.167 10 false SOL- 1.583,0.771 2.042,0.969 0.458,0.198 10 false C16
*a Component without harness connected
(Compressor Assembly with Pulley (Compressor Solenoid))


a.

Disconnect the C16 compressor assembly with pulley (compressor solenoid) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C16-1 (SOL-) - C16-2 (SOL+) 25°C (77°F) 10.1 to 11.1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (COMPRESSOR ASSEMBLY WITH PULLEY (COMPRESSOR SOLENOID) - BODY GROUND)

NG

REPLACE COMPRESSOR ASSEMBLY WITH PULLEY (COMPRESSOR SOLENOID)

6.CHECK HARNESS AND CONNECTOR (COMPRESSOR ASSEMBLY WITH PULLEY (COMPRESSOR SOLENOID) - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C16-1 (SOL-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (COMPRESSOR ASSEMBLY WITH PULLEY (COMPRESSOR SOLENOID) - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (COMPRESSOR ASSEMBLY WITH PULLEY (COMPRESSOR SOLENOID) - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the F80 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C16-2 (SOL+) - F80-2 (SOL+) Always Below 1 Ω
C16-2 (SOL+) or F80-2 (SOL+) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (When troubleshooting according to Problem Symptoms Table) A
OK (When troubleshooting according to the DTC) B
NG C



A

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR