Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) › from 2016.11
RM3160E _58 Vehicle Interior _019714 HEATING / AIR CONDITIONING _0109952 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  B1422  Compressor Lock Sensor Circuit  


DESCRIPTION

The ECM sends the engine speed signal to the air conditioning amplifier assembly via CAN communication.

The air conditioning amplifier assembly reads the difference between compressor speed and engine speed. When the difference becomes too large, the air conditioning amplifier assembly determines that the compressor is locked, and turns the magnetic clutch assembly off.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1422 Compressor Lock Sensor Circuit Open or short in A/C lock sensor circuit
·

Magnetic clutch assembly

·

Cooler compressor assembly

·

Harness or connector between cooler compressor assembly and air conditioning amplifier assembly

·

Air conditioning amplifier assembly


Memorized
(3 sec. or more)*

*: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.


WIRING DIAGRAM

E287484E02
1.125,1.083 1.583,1.281 0.458,0.198 10 false ECM 0.135,1.677 0.958,1.875 0.823,0.198 10 false from Battery 0.135,2.177 0.958,2.375 0.823,0.198 10 false from Battery 0.021,2.75 1,3.292 0.979,0.542 10 false from IG1 NO. 3 Relay 1.385,2.885 2.052,3.083 0.667,0.198 10 false IG1 NO. 3 1.531,2.354 2.167,2.552 0.635,0.198 10 false ALT 2.198,1.708 2.583,1.875 0.385,0.167 10 false 1H 2.208,2.74 2.594,2.906 0.385,0.167 10 false 1D 2.198,2.219 2.583,2.385 0.385,0.167 10 false 1A 2.198,3.26 2.583,3.427 0.385,0.167 10 false 1D 2.198,3.719 2.583,3.885 0.385,0.167 10 false 1G 3.563,1.719 3.906,1.927 0.344,0.208 10 false 1D 3.563,2.219 3.906,2.427 0.344,0.208 10 false 1D 2.24,1.5 2.583,1.667 0.344,0.167 10 false 1 2.25,2.01 2.594,2.177 0.344,0.167 10 false 1 2.208,2.521 2.583,2.688 0.375,0.167 10 false 11 2.208,3.031 2.583,3.198 0.375,0.167 10 false 14 2.25,3.51 2.594,3.677 0.344,0.167 10 false 5 2.646,5.323 4.427,5.552 1.781,0.229 10 false : CAN Communication Line 2.417,4.031 3.635,4.396 1.219,0.365 10 false Semiconductor Pwr Integration ECU 2.583,1.698 3.052,1.865 0.469,0.167 10 false BATT 2.583,2.198 3.052,2.365 0.469,0.167 10 false ALT 2.583,2.719 3.052,2.885 0.469,0.167 10 false IGN 2.583,3.25 3.052,3.417 0.469,0.167 10 false GND1 2.583,3.719 3.052,3.885 0.469,0.167 10 false GND2 3,1.729 3.448,1.948 0.448,0.219 10 false ACOS 3,2.229 3.667,2.542 0.667,0.313 10 false ACOP 3.604,1.521 3.948,1.688 0.344,0.167 10 false 4 3.573,2.021 3.917,2.188 0.344,0.167 10 false 12 4.167,2.125 4.51,2.292 0.344,0.167 10 false 3 4.333,2.125 4.677,2.333 0.344,0.208 10 false MG+ 4.365,3.583 5.615,3.792 1.25,0.208 10 false A/C Lock Sensor 4.156,3.302 4.5,3.469 0.344,0.167 10 false 2 5.104,3.292 5.521,3.5 0.417,0.208 10 false SSR+ 4.333,3.292 4.75,3.5 0.417,0.208 10 false SSR- 5.573,3.292 5.917,3.458 0.344,0.167 10 false 1 4.25,3.875 4.667,4.083 0.417,0.208 10 false C12 4.25,4.042 6.083,4.333 1.833,0.292 10 false Cooler Compressor Assembly 5.5,4.875 5.917,5.083 0.417,0.208 10 false F80 5.5,5.042 7.083,5.417 1.583,0.375 10 false Air Conditioning Amplifier Assembly 6,1.583 6.375,1.75 0.375,0.167 10 false 20 6.052,3.292 6.427,3.458 0.375,0.167 10 false 8 6.01,4.5 6.385,4.667 0.375,0.167 10 false 13 6.313,1.688 6.729,1.896 0.417,0.208 10 false MGC 6.313,3.396 6.729,3.604 0.417,0.208 10 false LOCK 6.313,4.635 6.729,4.844 0.417,0.208 10 false SG-2 4.448,2.625 5.5,3 1.052,0.375 10 false Magnetic Clutch Assembly 4.729,2.115 5.073,2.281 0.344,0.167 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

ECM malfunctions can affect the storage of this DTC. Therefore, check all SFI system DTCs and confirm that the system is normal before performing the following inspection.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Using the GTS, check if the CAN communication system is functioning normally.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
Result Proceed to
CAN communication system DTCs are not output A
CAN communication system DTCs are output B



A

2.PERFORM ACTIVE TEST USING GTS

B

2.PERFORM ACTIVE TEST USING GTS
a.

Disconnect the magnetic clutch assembly connector.


b.

Install SST to the connector on the magnetic clutch relay side.


SST
09843-18040  

c.

Connect the GTS to the DLC3.


d.

Start the engine.


e.

Turn the GTS on.


f.

Enter the following menus: Body Electrical / Air Conditioner / Active Test.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Magnetic Clutch Relay Air conditioning system operation OFF or ON -

g.
E248804C02
0.667,0.292 1.271,0.823 0.604,0.531 10 false *a
*a Front view of wire harness connector
(to Magnetic Clutch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 - Body ground
·

Engine is running

·

Active Test above is being performed


11 to 14 V


HINT:

When performing the Active Test, voltage between 11 and 14 V is output for approximately 3 seconds.



Result:
Proceed to
OK
NG



OK

3.INSPECT MAGNETIC CLUTCH ASSEMBLY

NG

3.INSPECT MAGNETIC CLUTCH ASSEMBLY
a.

Connect the magnetic clutch assembly connector.


b.

Disconnect the C12 cooler compressor assembly connector.


c.
E285435C01
1.271,1.75 1.646,1.448 false 0.167,0.146 0.479,0.302 0.313,0.156 10 false *a 1.115,1.76 1.594,2.052 0.479,0.292 10 false MG+
*a Component without harness connected
(Magnetic Clutch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (MG+) - Body ground 20°C (68°F) 3.8 to 4.2 Ω



d.

Connect a positive (+) lead from the battery to terminal 3 (MG+) and check that the following occurs: 1) the magnetic clutch assembly operating sound can be heard, and 2) the magnetic clutch hub and rotor lock.


Result:
Proceed to
OK
NG



OK

4.INSPECT COOLER COMPRESSOR ASSEMBLY

NG

4.INSPECT COOLER COMPRESSOR ASSEMBLY
E285435C02
1.125,0.708 1.531,1.188 false 2.146,0.729 1.844,1.167 false 0.146,0.208 0.458,0.365 0.313,0.156 10 false *a 0.729,0.604 1.219,0.885 0.49,0.281 10 false SSR- 2.25,0.625 2.74,0.906 0.49,0.281 10 false SSR+
*a Component without harness connected
(Cooler Compressor Assembly)


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SSR+) - 2 (SSR-) 20°C (68°F) 160 to 320 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (COOLER COMPRESSOR ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

5.CHECK HARNESS AND CONNECTOR (COOLER COMPRESSOR ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the F80 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C12-1 (SSR+) - F80-8 (LOCK) Always Below 1 Ω
C12-2 (SSR-) - F80-13 (SG-2) Always Below 1 Ω
C12-1 (SSR+) or F80-8 (LOCK) - Body ground Always 10 kΩ or higher
C12-2 (SSR-) or F80-13 (SG-2) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (When troubleshooting according to Problem Symptoms Table) A
OK (When troubleshooting according to the DTC) B
NG C



A

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR