While the engine is being cranked, current flows from terminal ST1 of the ignition switch assembly*1 or terminal STAR of the certification ECU (smart key ECU assembly)*2 to the park/neutral position switch assembly and to terminal STA of the ECM (STA signal).
*1: w/o Smart Entry and Start System.
*2: w/ Smart Entry and Start System.
Refer to DTC P0617.
Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>SFI SYSTEM>P0617
Inspect the fuses for circuits related to this system before performing the following procedure.
After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Check if the engine can be cranked.
| Result | Proceed to |
|---|---|
| Engine cannot be cranked | A |
| Engine can be cranked | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.
| Tester Display |
|---|
| Starter Signal |
Check the result when the ignition switch is ON and the engine starts.
| Condition | Starter Signal |
|---|---|
| Ignition switch ON | OFF |
| Cranking | ON |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ST relay.
Click hereEngine / Hybrid System>1AR-FE STARTING>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the starter assembly.
Click hereEngine / Hybrid System>1AR-FE STARTING>STARTER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST relay from the No. 1 engine room relay block and No. 1 junction block assembly.
Disconnect the starter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST relay terminal 3 - C18-1 | Always | Below 1 Ω |
| ST relay terminal 3 or C18-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) battery terminal.
Disconnect the cable from the positive (+) battery terminal.
Disconnect the starter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Positive (+) battery terminal - D2-1 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST relay from the No. 1 engine room relay block and No. 1 junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST relay terminal 1 - Body ground | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (w/o Smart Entry and Start System) | A |
| OK (w/ Smart Entry and Start System) | B |
| NG | C |
A
B
C
Remove the ST relay from the No. 1 engine room relay block and No. 1 junction block assembly.
Disconnect the park/neutral position switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C14-9 (L) - ST relay terminal 2 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ignition switch assembly.
Click hereEngine / Hybrid System>1AR-FE STARTING>IGNITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the ignition switch assembly connector.
Remove the ST relay from the No. 1 engine room relay block and No. 1 junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F50-2 (ST2) - ST relay terminal 5 | Always | Below 1 Ω |
| F50-2 (ST2) or ST relay terminal 5 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST relay from the No. 1 engine room relay block and No. 1 junction block assembly.
Disconnect the park/neutral position switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C14-9 (L) - ST relay terminal 2 | Always | Below 1 Ω |
| A43-22 (STA) - ST relay terminal 2 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the park/neutral position switch assembly.
Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION
| Result | Proceed to |
|---|---|
| OK (w/o Smart Entry and Start System) | A |
| OK (w/ Smart Entry and Start System) | B |
| NG | C |
A
B
C
Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>REMOVAL
Inspect the ignition switch assembly.
Click hereEngine / Hybrid System>1AR-FE STARTING>IGNITION SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the park/neutral position switch assembly connector.
Disconnect the ignition switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F50-6 (ST1) - C14-4 (B) | Always | Below 1 Ω |
| F50-6 (ST1) - C1-63 (NSW) | Always | Below 1 Ω |
| F50-6 (ST1) or C14-4 (B) or C1-63 (NSW) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST relay from the No. 1 engine room relay block and No. 1 junction block assembly.
Disconnect the park/neutral position switch assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST relay terminal 2 - C14-9 (L) | Always | Below 1 Ω |
| ST relay terminal 2 or C14-9 (L) or A43-22 (STA) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the park/neutral position switch assembly connector.
Disconnect the certification ECU (smart key ECU assembly) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F10-10 (STAR) - C14-4 (B) | Always | Below 1 Ω |
| F10-10 (STAR) - C1-63 (NSW) | Always | Below 1 Ω |
| F10-10 (STAR) or C14-4 (B) or C1-63 (NSW) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST relay from the No. 1 engine room relay block and No. 1 junction block assembly.
Disconnect the park/neutral position switch assembly connector.
Disconnect the ECM connector.
Disconnect the certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST relay terminal 2 - C14-9 (L) | Always | Below 1 Ω |
| ST relay terminal 2 or C14-9 (L) or A43-22 (STA) or F10-12 (STA) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.
| Tester Display |
|---|
| Starter Signal |
Check the result when the ignition switch is ON and the engine starts.
| Condition | Starter Signal |
|---|---|
| Ignition switch ON | OFF |
| Cranking | ON |
| Proceed to |
|---|
| OK |
| NG |
OK
NG