Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2016.11
RM3160E _58 Vehicle Interior _019708 METER / GAUGE / DISPLAY _0104486 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1500  Fuel Sender Open Detected  


DESCRIPTION

This DTC is stored when the combination meter assembly detects a fuel sender gauge assembly malfunction via a direct line.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
B1500 Fuel Sender Open Detected Diagnosis Condition
·

The ignition switch is ON.

·

IG power source voltage is 9.5 V or more.


Malfunction Status (for 1AR-FE):
·

Average input signal of fuel sender gauge assembly is 550 Ω or more 3 times consecutively


Malfunction Status (for 2GR-FKS):
·

Voltage signal from fuel sender gauge assembly is 0.2 V or less 3 times consecutively

·

Voltage signal from fuel sender gauge assembly is 4.7 V or more 3 times consecutively


·

Harness or connector

·

Fuel sender gauge assembly

·

Combination meter assembly

·

Fuel suction tube with pump and gauge assembly


- -

WIRING DIAGRAM

for 1AR-FE


E230580E50
5.26,3.104 7.146,3.333 1.885,0.229 10 false Combination Meter Assembly 5.719,0.979 5.99,1.135 0.271,0.156 10 false FR 5.719,2.344 6.125,2.5 0.406,0.156 10 false FE 5.552,0.885 6.01,1.271 0.458,0.385 10 false 4 5.469,2.229 5.823,2.573 0.354,0.344 10 false 23 2.323,2.229 2.438,2.375 0.115,0.146 10 false 3 2.323,0.885 2.438,1.031 0.115,0.146 10 false 2 0.365,3.104 4.479,3.281 4.115,0.177 10 false Fuel Suction Tube with Pump and Gauge Assembly 0.781,1.448 1.219,1.615 0.438,0.167 10 false Fuel 2.031,2.229 2.281,2.406 0.25,0.177 10 false FE 2.042,0.885 2.344,1.177 0.302,0.292 10 false FS 5.26,2.948 5.771,3.281 0.51,0.333 10 false F126 0.365,2.948 1.042,3.302 0.677,0.354 10 false M9 1.698,2.01 1.813,2.156 0.115,0.146 10 false 1 1.688,1.354 1.802,1.5 0.115,0.146 10 false 2 0.771,1.625 1.313,1.802 0.542,0.177 10 false Sender 0.771,1.792 1.271,2 0.5,0.208 10 false Gauge 0.771,1.948 1.49,2.146 0.719,0.198 10 false Assembly 0.781,1.271 1.083,1.563 0.302,0.292 10 false A


for 2GR-FKS


E285369E15
0.417,2.833 0.75,3 0.333,0.167 10 false M49 0.417,3 3.583,3.167 3.167,0.167 10 false Fuel Suction Tube with Pump and Gauge Assembly 5.25,2.833 5.625,3.042 0.375,0.208 10 false F126 5.25,3 7.083,3.167 1.833,0.167 10 false Combination Meter Assembly 0.781,1.479 1.25,1.667 0.469,0.188 10 false Sender 1.688,1.188 1.833,1.354 0.146,0.167 10 false 1 1.688,1.844 1.833,2.01 0.146,0.167 10 false 2 2.333,0.74 2.479,0.906 0.146,0.167 10 false 3 2.333,1.406 2.479,1.573 0.146,0.167 10 false 1 2.323,2.083 2.469,2.25 0.146,0.167 10 false 2 2.021,2.083 2.271,2.25 0.25,0.167 10 false FE 2.042,1.406 2.292,1.573 0.25,0.167 10 false FV 2.125,0.74 2.375,0.906 0.25,0.167 10 false S 5.531,0.74 5.781,0.906 0.25,0.167 10 false 4 5.542,1.406 5.792,1.573 0.25,0.167 10 false 3 5.469,2.083 5.719,2.25 0.25,0.167 10 false 23 5.74,0.833 6.156,1.135 0.417,0.302 10 false FR 5.74,1.5 5.99,1.667 0.25,0.167 10 false FV 5.74,2.167 6.031,2.375 0.292,0.208 10 false FE 0.781,1.313 1.094,1.49 0.313,0.177 10 false Fuel 0.781,1.646 1.229,1.854 0.448,0.208 10 false Gauge 0.781,1.813 1.417,2 0.635,0.188 10 false Assembly 1.823,1.417 1.969,1.583 0.146,0.167 10 false 3 0.802,1.125 0.948,1.292 0.146,0.167 10 false A


PROCEDURE

1.READ VALUE USING GTS (FUEL INPUT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Fuel Input Fuel input Min.: 0 L, Max.: 172.5 L Fuel receiver gauge indicates F: 64.8 L
Fuel receiver gauge indicates 3/4: 51.6 L
Fuel receiver gauge indicates 1/2: 36.0 L
Fuel receiver gauge indicates 1/4: 20.4 L
Fuel receiver gauge indicates E: 7.2 L
Unit: Liter
Body Electrical > Combination Meter > Data List
Tester Display
Fuel Input
50003 122 39

Result:
Result Proceed to
Fuel level data can be displayed on the GTS and DTC B1500 is output A
Fuel level data cannot be displayed on the GTS B



A

REPLACE COMBINATION METER ASSEMBLY

B

2.CONFIRM MODEL
2.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for 1AR-FE A
for 2GR-FKS B



A

3.INSPECT FUEL SENDER GAUGE ASSEMBLY

B

7.INSPECT FUEL SENDER GAUGE ASSEMBLY (POWER SOURCE)
3.INSPECT FUEL SENDER GAUGE ASSEMBLY
E254928C21
0.708,1.177 1.094,1.448 0.385,0.271 1.375,2.938 0.979,2.396 true 0.677,2.948 0.854,2.542 true 0.344,0.365 0.656,0.563 0.313,0.198 10 false *a 0.76,1.229 1.219,1.427 0.458,0.198 10 false F126 0.573,2.969 0.917,3.208 0.344,0.24 10 false FE 1.313,2.969 1.625,3.167 0.313,0.198 10 false FR
*a Front view of wire harness connector
(to Combination Meter Assembly)


a.

Disconnect the F126 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F126-4 (FR) - F126-23 (FE) Always 13.5 to 414.5 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY - COMBINATION METER ASSEMBLY)
4.CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the M9 fuel suction tube with pump and gauge assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M9-2 (FS) - F126-4 (FR) Always Below 1 Ω
M9-3 (FE) - F126-23 (FE) Always Below 1 Ω
M9-2 (FS) or F126-4 (FR) - Body ground Always 10 kΩ or higher
M9-3 (FE) or F126-23 (FE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT FUEL SENDER GAUGE ASSEMBLY
a.

Remove the fuel sender gauge assembly.

Click hereEngine / Hybrid System>1AR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL


b.

Inspect the fuel sender gauge assembly.

Click hereEngine / Hybrid System>1AR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>INSPECTION

OK:

Fuel sender gauge assembly is normal.



Result:
Proceed to
OK
NG



OK

6.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

NG

REPLACE FUEL SENDER GAUGE ASSEMBLY

6.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
E158805C66
0.313,1.333 0.74,1.635 0.427,0.302 0.313,3.667 0.729,3.958 0.417,0.292 1.406,1.198 1.156,0.74 false 1.802,1.219 2.125,0.729 false 0.125,0.188 1.563,0.354 1.438,0.167 10 false *a 0.427,1.406 0.76,1.656 0.333,0.25 10 false M9 0.458,3.74 0.792,3.99 0.333,0.25 10 false A 2.156,0.573 2.49,0.823 0.333,0.25 10 false FS 1.021,0.563 1.354,0.813 0.333,0.25 10 false FE
*a Component without harness connected
(Fuel Suction Tube with Pump and Gauge Assembly)


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M9-2 (FS) - A-2 Always Below 1 Ω
M9-3 (FE) - A-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

7.INSPECT FUEL SENDER GAUGE ASSEMBLY (POWER SOURCE)
E284677C31
1.5,0.208 1.906,0.458 0.406,0.25 2.615,1.677 2.469,1 true 0.198,0.156 0.51,0.313 0.313,0.156 10 false *a 1.563,0.25 2,0.469 0.438,0.219 10 false F126 2.552,1.708 2.865,1.865 0.313,0.156 10 false FV
*a Component with harness connected
(Combination Meter Assembly (Meter Circuit Plate))


a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F126-3 (FV) - Body ground Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

8.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY

8.INSPECT FUEL SENDER GAUGE ASSEMBLY
E284677C30
1.5,0.208 1.906,0.458 0.406,0.25 2.188,1.74 2.365,0.969 true 2.198,1.75 2.375,0.979 true 2.188,1.76 2.365,0.99 true 2.646,1.76 2.479,1.073 true 0.198,0.156 0.51,0.313 0.313,0.156 10 false *a 1.552,0.24 2.052,0.521 0.5,0.281 10 false F126 2.583,1.781 2.896,1.938 0.313,0.156 10 false FE 2.094,1.781 2.406,1.938 0.313,0.156 10 false FR
*a Component with harness connected
(Combination Meter Assembly)


a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F126-4 (FR) - F126-23 (FE) Ignition switch ON 0.5 to 4.4 V



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

9.CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY - COMBINATION METER ASSEMBLY)
9.CHECK HARNESS AND CONNECTOR (FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the F126 combination meter assembly connector.


b.

Disconnect the M49 fuel suction tube with pump and gauge assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M49-3 (S) - F126-4 (FR) Always Below 1 Ω
M49-2 (FE) - F126-23 (FE) Always Below 1 Ω
M49-1 (FV) - F126-3 (FV) Always Below 1 Ω
M49-3 (S) or F126-4 (FR) - Body ground Always 10 kΩ or higher
M49-2 (FE) or F126-23 (FE) - Body ground Always 10 kΩ or higher
M49-1 (FV) or F126-3 (FV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.INSPECT FUEL SENDER GAUGE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT FUEL SENDER GAUGE ASSEMBLY
a.

Remove the fuel sender gauge assembly.

Click hereEngine / Hybrid System>2GR-FKS FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL


b.

Inspect the fuel sender gauge assembly.

Click hereEngine / Hybrid System>2GR-FKS FUEL>FUEL SENDER GAUGE ASSEMBLY>INSPECTION

OK:

Fuel sender gauge assembly is normal.



Result:
Proceed to
OK
NG



OK

11.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

NG

REPLACE FUEL SENDER GAUGE ASSEMBLY

11.INSPECT FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
E158805C64
0.333,1.333 0.75,1.583 0.417,0.25 0.333,3.667 0.75,3.917 0.417,0.25 2.083,1.271 2.344,0.917 true 1.719,1.229 1.719,0.75 true 1.354,1.26 1.021,0.906 true 0.125,0.188 1.563,0.354 1.438,0.167 10 false *a 0.406,1.375 0.74,1.625 0.333,0.25 10 false M49 0.5,3.719 0.833,3.969 0.333,0.25 10 false A 0.906,0.76 1.24,1.01 0.333,0.25 10 false S 1.646,0.573 1.979,0.823 0.333,0.25 10 false FE 2.302,0.74 2.635,0.99 0.333,0.25 10 false FV
*a Component without harness connected
(Fuel Suction Tube with Pump and Gauge Assembly)


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M49-1 (FV) - A-3 Always Below 1 Ω
M49-2 (FE) - A-2 Always Below 1 Ω
M49-3 (S) - A-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY