Home › Drivetrain › UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › DIFFERENTIAL OIL SEAL(for RH Side) › from 2016.11
RM3160E _52 Drivetrain _060165 UA80F AUTOMATIC TRANSMISSION / TRANSAXLE _0300781 DIFFERENTIAL OIL SEAL(for RH Side) A

UA80F AUTOMATIC TRANSMISSION / TRANSAXLE  DIFFERENTIAL OIL SEAL(for RH Side)  REPLACEMENT  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

If automatic transaxle assembly parts are replaced, refer to Parts Replacement Compensation Table to determine if any additional operations are necessary.

Click hereDrivetrain>UA80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


Hide 36100 2.REMOVE TRANSFER ASSEMBLY

Hide 31105H 3.REMOVE TRANSAXLE CASE OIL SEAL

a.
C339268C01
1.219,0.292 1.531,0.292 1.531,0.292 2.26,1.125 true 1.052,0.177 1.365,0.333 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped with protective tape, remove the transaxle case oil seal from the transaxle housing.

NOTICE:

Be careful not to damage the front differential case or transaxle housing.



Hide 43410M 4.REMOVE FRONT DRIVE SHAFT OIL SEAL RH

a.
C343635N01
0.729,1.458 1.313,1.458 false 0.427,1.375 0.885,1.573 0.458,0.198 10 false SST

Using SST, remove the front drive shaft oil seal RH from the front differential case.

SST
09308-00010  

NOTICE:

Be careful not to damage the front differential case.



Hide 43410M 5.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.

Coat the lip of a new front drive shaft oil seal RH with MP grease.


b.
C363242C01
1.156,1.885 1.344,2.469 1.344,2.469 1.396,1.698 true 2.219,2.438 2.531,2.635 0.313,0.198 10 false *a 1.208,2.542 1.521,2.74 0.313,0.198 10 false SST
*a Depth


C343636C01
2.042,1.563 1.594,2.208 1.594,2.208 2.385,1.667 true 2.26,2.406 2.573,2.563 0.313,0.156 10 false *a 1.281,2.135 1.74,2.333 0.458,0.198 10 false SST
*a Depth


Using SST and a hammer, install the front drive shaft oil seal RH to the front differential case.

SST
09950-60010  (09951-00410)
09950-70010  (09951-07200)

Standard Depth:

21.5 to 22.5 mm (0.846 to 0.886 in.)


NOTICE:

Do not damage the lip of the front drive shaft oil seal RH.



Hide 31105H 6.INSTALL TRANSAXLE CASE OIL SEAL

a.

Coat the lip of a new front drive shaft oil seal RH with MP grease.


b.
C363242C01
1.156,1.885 1.344,2.469 1.344,2.469 1.396,1.698 true 2.219,2.438 2.531,2.635 0.313,0.198 10 false *a 1.208,2.542 1.521,2.74 0.313,0.198 10 false SST
*a Depth


C343637C01
0.792,1.917 0.969,2.521 0.969,2.521 1.083,1.688 true 2.24,2.385 2.552,2.583 0.313,0.198 10 false *a 0.844,2.563 1.302,2.76 0.458,0.198 10 false SST
*a Depth


Using SST and a hammer, install the transaxle case oil seal to the transaxle housing.

SST
09649-17010  
09950-70010  (09951-07200)

Standard Depth:

5.5 to 6.5 mm (0.217 to 0.256 in.)


NOTICE:
·

Make sure that the transaxle case oil seal is installed in the correct direction.

·

Do not damage the lip of the transaxle case oil seal.




Hide 36100 7.INSTALL TRANSFER ASSEMBLY