Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.11
RM3160E _54 Brake _019692 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0106374 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1225  SM Solenoid Circuit  C1468  SFR Solenoid Circuit  C1469  SFL Solenoid Circuit  C146A  SRR Solenoid Circuit  C146B  SRL Solenoid Circuit  


DESCRIPTION

These solenoids turn on when signals are received from the skid control ECU (brake actuator assembly) and they control the pressure acting on the wheel cylinders to control the braking force.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1225 SM Solenoid Circuit Any of the following is detected:
1.

While master cylinder cut solenoid outputs ON, overcurrent continues for 0.1 seconds or more.

2.

While master cylinder cut solenoid outputs OFF, open circuit continues for 0.05 seconds or more.

3.

While master cylinder cut solenoid outputs ON, open circuit continues for 0.05 seconds or more.

4.

While master cylinder cut solenoid outputs OFF, current is maintained for 0.05 seconds or more.

5.

Difference in master cylinder cut solenoid output accuracy continues for 0.2 seconds or more.


Brake actuator assembly
C1468 SFR Solenoid Circuit Any of the following is detected:
1.

Open or short circuit in decompression solenoid continues for 0.05 seconds or more.

2.

While holding solenoid outputs OFF, open circuit continues for 0.05 seconds or more.

3.

While holding solenoid outputs OFF, current is maintained for 0.05 seconds or more.

4.

While holding solenoid outputs ON, overcurrent continues for 0.1 seconds or more.

5.

While holding solenoid outputs ON, open circuit continues for 0.05 seconds or more.

6.

Difference in holding solenoid LH and RH accuracy continues for 0.2 seconds or more.


Brake actuator assembly
C1469 SFL Solenoid Circuit Any of the following is detected:
1.

Open or short circuit in decompression solenoid continues for 0.05 seconds or more.

2.

While holding solenoid outputs OFF, open circuit continues for 0.05 seconds or more.

3.

While holding solenoid outputs OFF, current is maintained for 0.05 seconds or more.

4.

While holding solenoid outputs ON, overcurrent continues for 0.1 seconds or more.

5.

While holding solenoid outputs ON, open circuit continues for 0.05 seconds or more.

6.

Difference in holding solenoid LH and RH accuracy continues for 0.2 seconds or more.


Brake actuator assembly
C146A SRR Solenoid Circuit Any of the following is detected:
1.

Open or short circuit in decompression solenoid continues for 0.05 seconds or more.

2.

While holding solenoid outputs OFF, open circuit continues for 0.05 seconds or more.

3.

While holding solenoid outputs OFF, current is maintained for 0.05 seconds or more.

4.

While holding solenoid outputs ON, overcurrent continues for 0.1 seconds or more.

5.

While holding solenoid outputs ON, open circuit continues for 0.05 seconds or more.

6.

Difference in holding solenoid LH and RH accuracy continues for 0.2 seconds or more.


Brake actuator assembly
C146B SRL Solenoid Circuit Any of the following is detected:
1.

Open or short circuit in decompression solenoid continues for 0.05 seconds or more.

2.

While holding solenoid outputs OFF, open circuit continues for 0.05 seconds or more.

3.

While holding solenoid outputs OFF, current is maintained for 0.05 seconds or more.

4.

While holding solenoid outputs ON, overcurrent continues for 0.1 seconds or more.

5.

While holding solenoid outputs ON, open circuit continues for 0.05 seconds or more.

6.

Difference in holding solenoid LH and RH accuracy continues for 0.2 seconds or more.


Brake actuator assembly

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.RECONFIRM DTC
HINT:

These codes are detected when a problem is determined in the skid control ECU (brake actuator assembly).

The solenoid circuits are in the brake actuator assembly.

Therefore, solenoid circuit inspection and solenoid unit inspection cannot be performed. Be sure to check if any DTCs are output before replacing the skid control ECU (brake actuator assembly).


a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Perform a road test.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTCs C1225, C1468, C1469, C146A and C146B are not output. A
DTCs C1225, C1468, C1469, C146A and/or C146B are output. B


HINT:
·

The skid control ECU (brake actuator assembly) performs self diagnosis of the solenoid circuit after the ignition switch is turned to ON.

·

If the normal system code is output (no DTCs are output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU (brake actuator assembly).

·

If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

If no DTCs were output when reconfirming DTCs, checking for intermittent problems is necessary because it is suspected that the original DTCs were stored due to the poor connection of a connector terminal.





A

B