Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Smart Entry and Start System) › from 2016.11
RM3160E _58 Vehicle Interior _019706 THEFT DETERRENT / KEYLESS ENTRY _0097123 IMMOBILISER SYSTEM(w/o Smart Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Smart Entry and Start System)  Engine does not Start because No Initial Combustion  


DESCRIPTION

·

When a door control transmitter assembly is inserted into the ignition key cylinder, the transponder key coil receives the key ID code and sends it to the transponder key ECU assembly.

·

If an error in communication between the transponder key coil and transponder key ECU assembly occurs, this symptom may occur.


WIRING DIAGRAM

B329324E26
5.469,2.542 5.927,2.74 0.458,0.198 10 false F66 5.469,2.698 6.948,3.146 1.479,0.448 10 false Transponder Key ECU Assembly 1.292,3.042 1.75,3.24 0.458,0.198 10 false F53 1.281,3.188 3.125,3.49 1.844,0.302 10 false Transponder Key Coil 2.792,0.76 3.552,1.052 0.76,0.292 10 false ANT1 2.781,1.948 3.542,2.24 0.76,0.292 10 false ANT2 5.667,0.896 6.427,1.188 0.76,0.292 10 false ANT1 5.677,2.063 6.438,2.354 0.76,0.292 10 false ANT2 5.51,0.802 5.75,1.042 0.24,0.24 10 false 4 5.427,1.958 5.667,2.198 0.24,0.24 10 false 15 3.25,0.75 3.49,0.99 0.24,0.24 10 false 1 3.229,1.948 3.469,2.188 0.24,0.24 10 false 5

CAUTION / NOTICE / HINT

NOTICE:

If the transponder key ECU assembly or door control transmitter assembly is replaced, refer to Service Bulletin.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234
Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Immobiliser > Trouble Codes
50001 260
Powertrain > Engine and ECT > Trouble Codes
50001 234
Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

3.READ VALUE USING GTS (IMMOBILISER FUEL CUT)

B

3.READ VALUE USING GTS (IMMOBILISER FUEL CUT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Engine and ECT*1 or Engine*2 / Data List.

*1: for 1AR-FE

*2: for 2GR-FKS



e.

Read the Data List according to the display on the GTS.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Immobiliser Fuel Cut Status of immobiliser system fuel cut ON or OFF - -
Powertrain > Engine and ECT > Data List
Tester Display
Immobiliser Fuel Cut
50003 234 505
Powertrain > Engine
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Immobiliser Fuel Cut Status Status of immobiliser system fuel cut ON or OFF - -
Powertrain > Engine > Data List
Tester Display
Immobiliser Fuel Cut Status
50003 372 65
OK:

OFF is displayed after the engine is started.



Result:
Proceed to
OK
NG



OK

NG

4.CHECK SECURITY INDICATOR LIGHT OPERATION
4.CHECK SECURITY INDICATOR LIGHT OPERATION
a.

Check that the security indicator light turns off when a registered door control transmitter assembly is inserted into the ignition key cylinder.

OK:

Security indicator light turns off.



Result:
Proceed to
OK
NG



OK

NG

5.CHECK SECURITY INDICATOR LIGHT OPERATION
5.CHECK SECURITY INDICATOR LIGHT OPERATION
a.

Check that the security indicator light turns off when another registered door control transmitter assembly is inserted into the ignition key cylinder.

OK:

Security indicator light turns off.



Result:
Proceed to
OK
NG



OK

6.CHECK WHETHER ENGINE STARTS

NG

7.REPLACE TRANSPONDER KEY COIL
6.CHECK WHETHER ENGINE STARTS
a.

Using another registered door control transmitter assembly, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Result Proceed to
Engine can be started A
Engine cannot be started B



A

11.REPLACE DOOR CONTROL TRANSMITTER ASSEMBLY

B

7.REPLACE TRANSPONDER KEY COIL

Result:
Proceed to
NEXT



NEXT

8.CHECK WHETHER ENGINE STARTS
8.CHECK WHETHER ENGINE STARTS
a.

Using a registered door control transmitter assembly, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Result Proceed to
Engine can be started A
Engine cannot be started B



A

END (TRANSPONDER KEY COIL WAS DEFECTIVE)

B

9.REPLACE TRANSPONDER KEY ECU ASSEMBLY
9.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to Service Bulletin.


NOTICE:

Key ID code registration is necessary when replacing the transponder key ECU assembly, refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER ENGINE STARTS
10.CHECK WHETHER ENGINE STARTS
a.

Using a registered door control transmitter assembly, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Result Proceed to
Engine can be started A
Engine cannot be started B



A

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

B

11.REPLACE DOOR CONTROL TRANSMITTER ASSEMBLY
11.REPLACE DOOR CONTROL TRANSMITTER ASSEMBLY
a.

Replace the door control transmitter assembly.

NOTICE:

Key ID code registration is necessary when replacing the door control transmitter assembly, refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

12.CHECK WHETHER ENGINE STARTS
12.CHECK WHETHER ENGINE STARTS
a.

Using a registered door control transmitter assembly, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Result Proceed to
Engine can be started A
Engine cannot be started B



A

END (DOOR CONTROL TRANSMITTER ASSEMBLY WAS DEFECTIVE)

B