Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Smart Entry and Start System) › from 2016.11
RM3160E _58 Vehicle Interior _019706 THEFT DETERRENT / KEYLESS ENTRY _0097123 IMMOBILISER SYSTEM(w/o Smart Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Smart Entry and Start System)  Engine does not Start but Initial Combustion Occurs  


DESCRIPTION

If the key ID codes of the door control transmitter assembly and transponder key ECU assembly match, the immobiliser system is unset and the engine start permission signal is sent to the ECM. When the ID codes of the transponder key ECU assembly and ECM match, the engine starts.

WIRING DIAGRAM

B366892E24
1.479,1.406 1.833,1.594 0.354,0.188 10 false IMI 1.417,0.771 1.771,0.958 0.354,0.188 10 false IMO 1.24,1.927 1.708,2.167 0.469,0.24 10 false ECM 0.927,1.927 1.396,2.167 0.469,0.24 10 false A43 5.083,1.917 5.552,2.156 0.469,0.24 10 false F66 5.396,1.917 6.469,2.313 1.073,0.396 10 false Transponder Key ECU Assembly 1.792,1.302 2.698,1.521 0.906,0.219 10 false 28*1, 59*2 1.792,0.656 2.698,0.875 0.906,0.219 10 false 29*1, 45*2 2.708,2.052 3.896,2.281 1.188,0.229 10 false *1: for 1AR-FE 2.708,2.354 3.896,2.583 1.188,0.229 10 false *2: for 2GR-FKS 5.479,1.417 5.979,1.625 0.5,0.208 10 false EFIO 5.479,0.771 5.979,0.979 0.5,0.208 10 false EFII 5.229,0.656 5.51,0.865 0.281,0.208 10 false 12 5.219,1.302 5.5,1.51 0.281,0.208 10 false 13

CAUTION / NOTICE / HINT

NOTICE:

If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Immobiliser > Clear DTCs
50002 260
Powertrain > Engine and ECT > Clear DTCs
50002 234
Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Immobiliser > Trouble Codes
50001 260
Powertrain > Engine and ECT > Trouble Codes
50001 234
Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

3.READ VALUE USING GTS (IMMOBILISER FUEL CUT)

B

3.READ VALUE USING GTS (IMMOBILISER FUEL CUT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Engine and ECT*1 or Engine*2 / Data List.

*1: for 1AR-FE

*2: for 2GR-FKS



e.

Read the Data List according to the display on the GTS.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Immobiliser Fuel Cut Status of immobiliser system fuel cut ON or OFF - -
Powertrain > Engine and ECT > Data List
Tester Display
Immobiliser Fuel Cut
50003 234 505
Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Immobiliser Fuel Cut Status Status of immobiliser system fuel cut ON or OFF - -
Powertrain > Engine > Data List
Tester Display
Immobiliser Fuel Cut Status
50003 372 65
OK:

OFF is displayed after the engine is started.



Result:
Proceed to
OK
NG



OK

NG

4.CHECK WHETHER ENGINE STARTS
4.CHECK WHETHER ENGINE STARTS
a.

Using a registered door control transmitter assembly, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Result Proceed to
Engine can be started A
Engine cannot be started B



A

B

5.CHECK ECM (TERMINAL IMI)
5.CHECK ECM (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform.

B354439C22
2.406,0.344 2.771,0.594 0.365,0.25 5.417,0.344 5.781,0.594 0.365,0.25 5.417,2.219 5.125,1.208 false 4.51,2.208 5.01,1.375 false 0.354,0.25 0.667,0.448 0.313,0.198 10 false *a 2.24,3.01 2.552,3.208 0.313,0.198 10 false *b 3.365,4.115 3.677,4.313 0.313,0.198 10 false *c 5.323,2.24 5.719,2.479 0.396,0.24 10 false IMI 2.51,0.375 2.906,0.615 0.396,0.24 10 false C1 1.021,4.031 1.417,4.271 0.396,0.24 10 false GND 5.479,0.375 5.875,0.615 0.396,0.24 10 false A43 4.344,2.24 4.625,2.469 0.281,0.229 10 false IMI 5.542,2.229 5.917,2.469 0.375,0.24 12 false *A 4.563,2.219 4.938,2.458 0.375,0.24 12 false *B
*A for 1AR-FE *B for 2GR-FKS
*a Component with harness connected
(ECM)
*b Waveform 1
*c Waveform 2 - -


OK
Tester Connection Condition Tool Setting Specified Condition
A43-28 (IMI) - Body ground*1 Ignition switch ON 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)
A43-59 (IMI) - Body ground*2

*1: for 1AR-FE

*2: for 2GR-FKS



Result:
Result Proceed to
Normal waveform A
Waveform 1 not output, or has abnormal wavelength or shape B
Waveform 2 not output, or has abnormal wavelength or shape C



A

6.CHECK ECM (TERMINAL IMO)

B

12.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)

C

13.REPLACE TRANSPONDER KEY ECU ASSEMBLY
6.CHECK ECM (TERMINAL IMO)
a.

Using an oscilloscope, check the waveform.

B319577C64
2.427,0.365 2.844,0.646 0.417,0.281 5.448,0.354 5.865,0.635 0.417,0.281 5.292,2.052 5.01,1.208 false 4.51,2.063 4.917,1.281 false 0.219,0.219 0.531,0.417 0.313,0.198 10 false *a 1.01,4.042 1.396,4.292 0.385,0.25 10 false GND 2.938,4.094 3.323,4.344 0.385,0.25 10 false *b 2.552,0.406 2.938,0.656 0.385,0.25 10 false C1 5.115,2.083 5.646,2.313 0.531,0.229 10 false IMO 5.531,0.406 5.833,0.594 0.302,0.188 10 false A43 4.323,2.094 4.854,2.323 0.531,0.229 10 false IMO 4.594,2.073 4.969,2.313 0.375,0.24 12 false *B 5.406,2.073 5.781,2.313 0.375,0.24 12 false *A
*A for 1AR-FE *B for 2GR-FKS
*a Component with harness connected
(ECM)
*b Waveform


OK
Tester Connection Condition Tool Setting Specified Condition
A43-29 (IMO) - Body ground*1 Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal 2 V/DIV., 500 ms./DIV. Pulse generation
(See waveform)
A43-45 (IMO) - Body ground*2

*1: for 1AR-FE

*2: for 2GR-FKS



Result:
Result Proceed to
Normal waveform A
Waveform not output, or has abnormal wavelength or shape B



A

7.REGISTER ECU COMMUNICATION ID

B

9.REPLACE ECM
7.REGISTER ECU COMMUNICATION ID
a.

Register the communication ID between the transponder key ECU assembly and ECM.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

8.CHECK WHETHER ENGINE STARTS
8.CHECK WHETHER ENGINE STARTS
a.

Using a registered door control transmitter assembly, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Result Proceed to
Engine can be started A
Engine cannot be started B



A

END (REGISTERED COMMUNICATION ID WAS DEFECTIVE)

B

13.REPLACE TRANSPONDER KEY ECU ASSEMBLY
9.REPLACE ECM
a.

Temporarily replace the ECM with a new one.

for 1AR-FE: Click hereEngine / Hybrid System>1AR-FE ENGINE CONTROL>ECM>REMOVAL

for 2GR-FKS: Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>ECM>REMOVAL


Result:
Proceed to
NEXT



NEXT

10.REGISTER ECU COMMUNICATION ID
10.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

11.CHECK WHETHER ENGINE STARTS
11.CHECK WHETHER ENGINE STARTS
a.

Using a registered door control transmitter assembly, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (ECM WAS DEFECTIVE)

NG

12.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM)
a.

Disconnect the F66 transponder key ECU assembly connector.


b.

Disconnect the A43 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F66-13 (EFIO) - A43-28 (IMI)*1 Always Below 1 Ω
F66-13 (EFIO) - A43-59 (IMI)*2 Always Below 1 Ω
A43-28 (IMI) or F66-13 (EFIO) - Body ground*1 Always 10 kΩ or higher
A43-59 (IMI) or F66-13 (EFIO) - Body ground*2 Always 10 kΩ or higher


*1: for 1AR-FE

*2: for 2GR-FKS



Result:
Proceed to
OK
NG



OK

13.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

NOTICE:

Key ID code registration is necessary when replacing the transponder key ECU assembly, refer to Service Bulletin.


HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

14.CHECK WHETHER ENGINE STARTS
14.CHECK WHETHER ENGINE STARTS
a.

Using a registered door control transmitter assembly, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

NG